Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for OLIMEX MSP430-CCRF
Summary of Contents for OLIMEX MSP430-CCRF
-
Page 1: Users Manual
MSP430-CCRF development board Users Manual All boards produced by Olimex are ROHS compliant Revision A, June 2011 Copyright(c) 2011, OLIMEX Ltd, All rights reserved Page 1... -
Page 2: Board Features
Dimensions: 78.49 x 39.12mm (3.09 x 1.54") ELECTROSTATIC WARNING: The MSP430-CCRF board is shipped in protective anti-static packaging. The board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. -
Page 3: Board Use Requirements
Hardware: MSP-JTAG-ISO MSP-JTAG MSP-JTAG-RF , or other compatible programming/debugging tool. You can also use other Olimex's board MSP-CCRF, or MSP-CCRF-LCD for radio communication. PROCESSOR FEATURES: MSP430-CCRF board use microcontroller CC430F5137IRGZFBD100 with these features: − True System-on-Chip (SoC) for Low-Power Wireless Communication Applications −... - Page 4 − Serial Onboard Programming, No External Programming Voltage Needed − Embedded Emulation Module (EEM) − High-Performance Sub-1-GHz RF Transceiver Core − Wide Supply Voltage Range: 2.0 V to 3.6 V − Frequency Bands: 300 MHz to 348 MHz, 389 MHz to 464 MHz, and 779 MHz to 928 MHz.
-
Page 5: Block Diagram
BLOCK DIAGRAM: Page 5... -
Page 6: Memory Organization
MEMORY ORGANIZATION: (1) All memory regions not specified here are vacant memory, and any access to them causes a Vacant Memory Interrupt. Page 6... - Page 7 SCHEMATIC: GYX-SD-TC0805SURK(RED) 100nF 100nF 10uF/6.3V 100nF 100nF 10uF/6.3V 100nF 100nF 10uF/6.3V 100nF 100nF 100nF 10uF/6.3V 10uF/16V 100nF IT1185AU2 Page 7...
-
Page 8: Board Layout
The programmed board power consumption is about 25 mA with all peripherals enabled. RESET CIRCUIT: MSP430-CCRF reset circuit includes R2 (330Ω), R1 (33k), C1 (2.2nF), JTAG pin 11 and CC430F5137IRGZ pin 40 (#RST/SWBTDIO). CLOCK CIRCUIT: Quartz crystal Q1 32.768 kHz is connected to CC430F5137IRGZ pin 44 (P5.0/XIN) and pin 43 (P5.1/XOUT). -
Page 9: Jumper Description
JUMPER DESCRIPTION: This jumper, when is in position 1-2 – UEXT pin 3 (signal TX) is connected to CC430F5137IRGZ pin 5 (signal BSLTX/UCA0TXD); when the jumper is in position 2- - UEXT pin 3 (signal TX) is connected to CC430F5137IRGZ pin 6 (signal BSLRX/UCA0RXD) Default state is shorted in position 2-3. -
Page 10: External Connectors Description
EXTERNAL CONNECTORS DESCRIPTION: JTAG: Pin # Signal Name Pin # Signal Name JTAG power supply Not Connected TEST/SWBTCK Not Connected #RST/SWBTDIO BSLTX/UCA0TXD Not Connected BSLRX/UCA0RXD PWR: Pin # Signal Name Page 10... - Page 11 UEXT: Pin # Signal Name UCB0_MISO/SC UCB0_MOSI/SD UCB0_CLK UCB0_STE Page 11...
- Page 12 Pin holes: Pin # Signal Name Pin # Signal Name PJ.0 P2.6 P2.6 PJ.1 P2.7 P2.7 PJ.2 P3.0 P3.0 PJ.3 P3.1 P3.1 TEST TEST/SWBTCK P3.2 P3.2 #RST/SWBTDIO P3.3 P3.3 3.3V P3.4 P3.4 P3.5 P3.5 P2.5 P2.5 P3.6 P3.6 P2.4 P2.4 P3.7 P3.7 P2.3...
-
Page 13: Mechanical Dimensions
MECHANICAL DIMENSIONS: Page 13... -
Page 14: Available Demo Software
AVAILABLE DEMO SOFTWARE: Blinking Led sourced by DCO Blinking Led sourced by RTC Blinking Led sourced by RTC and USART Echo Toggle LED when BUT is pressed RF Connection_ press BUT to send a packet and toggle LED when packet is ... -
Page 15: Order Code
Rev. A, June 2011 - in BOARD FEATURES - added Supported radio frequencies bands, Maximal permissible distance between two MSP430-CCRF boards, RTC crystal and “Not typical power jack” changed to “PWR jack for 2 x 1.5V AA batteries “ Page 15... - Page 16 This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product.