Sharp LC-32LE631E Service Manual page 71

Circuit Descriptions (continued)
• the switching frequency of the +5V-DVBS to +1-DVBS
switched mode converter is 900 kHz (item no. 7T00)
• a delay line for the +2V5-DVBS and +1V-DVBS lines is
created with item no. 3T03 (R=10k) and 2T06 (C=100n)
• a 3.3V to 2.5V linear stabiliser is built around item no. 7T01
• a 5V to 3.3V linear stabiliser is built around item no. 7T02.
Diagram B08B contains the DVB-S2 LNB supply:
• the +V-LNB signal comes from item no. 7T03
• the V0-CTRL signal goes to item no. 7T03
• the LNB-RF1 goes to the LNB.
Figures gives a graphical representation of the DC/DC
converters with its current consumptions:
+ 5V 5-TUN
+ 5V
+ 5V
dc -dc
+ 12V + 3V 3
+ 3V 3
2919 m A
dc -dc
+ 1V 8
+ 1V 8
dc -dc
+ 1V 1
+ 1V 1
dc -dc
Figure 7-3 DC/DC converters
7.4 Front-End Analogue and DVB-T, DVB-C;
ISDB-T reception
7.4.1 European/China region
The Front-End for the European/China region consist of the
following key components:
• Hybrid Tuner
• Switchable SAW filter 7/8 MHz (Eur.), or single SAW filter
(8 MHz) (China)
• Bandpass filter
• Amplifier
• PNX855xx SoC TV processor with integrated DVB-T and
DVB-C channel decoder and analogue demodulator.
Below find a block diagram of the front-end application for this
region.
Figure 7-4 Front-End block diagram European/China region
196 m A
+ 5V 5-TUN + 5V -TUN
+ 5V -TUN
2179 m A 196 m A
s tabiliz er
+ 3V 3 + 2V 5
+ 2V 5
2371 m A 450 m A
s tabiliz er
+ 1V 8 + 1V 2
+ 1V 2
2450 m A 550 m A
s tabiliz er
5100 m A
18770_226_100127.eps
100426
18770_235_100127.eps
100219
7.5 Front-End DVB-S(2) reception
The Front-End for the DVB-S(2) application consist of the
following key components:
2
• Satellite Tuner; I C address 0xC6 (bridged via channel
decoder)
2
• Channel decoder; I C address 0xD0
• LNB switching regulator; I
• Amplifier
• PNX855xx SoC TV processor with integrated DVB-T and
DVB-C channel decoder and analogue demodulator.
Below find a block diagram of the front-end application for
DVB-S(2) reception.
Figure 7-5 Front-End block diagram DVB-S(2) reception
This application supports the following protocols:
• Polarization selection via supply voltage (18V = horizontal,
13V = vertical)
• Band selection via "toneburst" (22 kHz): tone "on" = "high"
band, tone "off" = "low" band
• Satellite (LNB) selection via DiSEqC 1.0 protocol
• Reception of DVB-S (supporting QPSK encoded signals)
and DVB-S2 (supporting QPSK, 8PSK, 16APSK and
32APSK encoded signals), introducing LDPC low-density
parity check techniques.
7.6 HDMI
In this platform, the Silicon Image Sil9x87 HDMI multiplexer is
implemented. Refer to figure
the application.
71
LC-32LE631
LC-40LE631
LC-46LE631
2
C address 0x14
18770_237_100127.eps
100219
7-6 HDMI input configuration for