Adjusting The 3D-Phonic Modes - JVC RX-8010RBK Service Manual

4. Press LEVEL +/– to adjust the
speaker output levels (–10 dB to
+10 dB).
5. Press SOUND.
• To adjust other speaker output levels, repeat
steps 3 and 4.
6. Press CTR TONE to select the
center tone level you want — for
5 CH Stereo mode only.
• Each time you press the button, the display
changes to show the following:
CTR TONE 2
CTR TONE 1
(Softer)
CTR TONE 5
(Sharper)
To make the dialogue softer, select "CTR TONE 1" or "CTR
TONE 2."
To make the dialogue clearer, select "CTR TONE 4" or "CTR
TONE 5."
When "CTR TONE 3" is selected, no adjustment is applied.

Adjusting the 3D-PHONIC Modes

Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 17).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
• You cannot adjust the center speaker output level when you have
set "CTR SPK" to "NONE," See page 17.
• To adjust the front speaker output balance and subwoofer output
level, see pages 16 and 17.
On the front panel:
1. Press DSP MODE repeatedly until
"3D ACTION" or "3D DIGITAL"
appears on the display.
The DSP MODE lamp on the front panel
button lights up, and the 3D-PHONIC and DSP indicators also
light up on the display.
2. Adjust the center speaker output level.
1) Press LEVEL ADJUST repeatedly
until "CENTER" appears on the
display.
2) Press CONTROL UP 5/DOWN ∞ to
adjust the center speaker output level
(from –10 dB to +10 dB).
37
∗
BAL L
+
∗
CH/ LEVEL
−
∗
BAL R
SOUND
CTR TONE
5
ENTER
CTR TONE 3
(Soft) (Flat)
CTR TONE 4
(Sharp)
DSP MODE
L LEVEL
ADJUST
CONTROL
DOWN UP
3. Adjust the center tone.
1) Press EFFECT repeatedly until "CTR
TONE" appears on the display.
The display shows the current setting.
2) Press CONTROL UP 5/DOWN ∞
to select the center tone level you
want.
The center tone adjustment affects the
mid-frequency range, which the human
voice is mostly made up of.
• Each time you press the button, the
display changes to show the following:
CTR TONE 2
CTR TONE 1
(Softer)
CTR TONE 5
(Sharper)
To make the dialogue softer, select "CTR TONE 1" or
"CTR TONE 2."
To make the dialogue clearer, select "CTR TONE 4" or
"CTR TONE 5."
When "CTR TONE 3" is selected, no adjustment is applied.
4. Adjust the overall levels of the effect.
1) Press EFFECT repeatedly until
"EFFECT" appears on the display.
The display shows the current setting.
2) Press CONTROL UP 5/DOWN ∞
to select the effect level you want.
• Each time you press the button, the
display changes to show the following:
EFFECT 1 EFFECT 2
EFFECT 5
As the number increases, the selected 3D effect mode
becomes stronger. (Normally set it to "EFFECT 3.")
From the remote control:
1. Press DSP MODE repeatedly until
"3D ACTION" or "3D DIGITAL"
appears on the display.
The DSP MODE lamp on the front panel button lights up, and
the 3D-PHONIC and DSP indicators also light up on the display.
2. Press SOUND.
The 10 keys are activated for sound
adjustments.
3. Press CENTER to select the center
speaker.
• "CTR" appears on the remote control display
window.
4. Press LEVEL +/– to adjust the
center speaker output levels (from
–10 dB to +10 dB).
5. Press SOUND.
EFFECT SETT
CONTROL
DOWN UP
CTR TONE 3
(Soft) (Flat)
CTR TONE 4
(Sharp)
EFFECT SETT
CONTROL
DOWN UP
EFFECT 3
EFFECT 4
DSP
MODE
SOUND
∗
CENTER
9
∗
BAL L
+
∗
CH/ LEVEL
−
∗
BAL R
SOUND