Page 1
Ver 1.2 2006.09 AEP Model UK Model E Model Australian Model • HCD-LF1 is DVD/CD DECK system in DAV-LF1. * Manufactured under license from Dolby Laboratories. Model Name Using Similar Mechanism “Dolby”, “Pro Logic”, and the double-D symbol are trademarks Mechanism Type CDM80AT-DVBU29T of Dolby Laboratories.
Page 2
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
HCD-LF1 SECTION 1 SERVICING NOTES NOTE 1: Regarding the notification symbol “R” NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK Because the number of the operating buttons of this product OR BASE UNIT are limited, some operations require use of the operating...
Page 5
HCD-LF1 • NOTE * The performance of the main unit can be connected with the remote controller, even if the panel is not connected. • CAUTION-1 (REPLACING THE TOUCH KEY BOARD) TOUCH PAD (B) BOARD CL405 CL406 CL404 CL414 CL415...
Page 6
HCD-LF1 • CAUTION-2 (REPLACING THE CONNECTING CORD) * When replacing the connecting cord, fix it at the position in the figure so that the copper conductor of the cord and the steel plate contact (GND) adequately. copper conductor of the cord connecting cord •...
Page 7
HCD-LF1 • SERVICING POSITION-2 (DMB07 BOARD) * Connect the I/O BOARD and the DMB07 BOARD by using the three extension cables, and inspect the DMB07 BOARD. extension cable J-2501-199-A (25P/L300) extension cable J-2501-225-A (9P/L300) extension cable J-2501-243-A (17P/L300) I/O BOARD...
HCD-LF1 SECTION 2 GENERAL This section is extracted from instruction manual. Front Panel FUNCTION VOL. Top Panel A DISC indicator H [/1 (power) switch/standby indicator (39) B Touch Panel Sensor (41) I Disc slot (39) C Front panel display (104)
Page 9
P ENTER Q TUNER MENU (79, 81) R TV [/1 (on/standby) (74) S "/1 (standby) (34, 39, 80) T SONY TV DIRECT (76) U TUNER/BAND (79, 80, 81) V FUNCTION (39, 78, 80, 81) W m/M/SLOW , TUNING –/+ (47, 52, 79, 80) Open the cover.
HCD-LF1 SECTION 3 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. • The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are completed.
HCD-LF1 3-2. STAND SECTION 2 four claws 1 two screws (HEX 4 × 10) 4 stand section 3 cover (rear) 3-3. COVER (MAIN/CDM) 9 four covers (SH) 3 two screws q; four screws (+BVTP 3 × 8) 6 four claws...
HCD-LF1 3-13. LEVER (LOADING R/L) spr-T (loading L) spr-T (loading R) 5 lever (loading R) 2 two hooks 4 two hooks 3 lever (loading L) PRECAUTION DURING LEVER (LOADING R / L) INSTALLATION Align the horizontal position. lever (loading L) lever (loading R) Install the both levers so that they move symmetrically.
HCD-LF1 3-14. DISC STOP LEVER, DISC SENSOR LEVER 1 gear (cap) 2 gear (IDL L) PRECAUTION DURING DISC STOP LEVER INSTALLATION chassis (top) hole 5 two hooks 3 two claws disc stop lever 6 disc stop lever hole Install the disc stop lever so that the both holes are aligned.
HCD-LF1 3-18. BASE UNIT 4 floating screw (+PTPWHM 2.6) 6 base unit 3 holder down spring 5 floating screw (+PTPWHM 2.6) 2 lever (CL UP2) 1 screw (+BVTP 2.6 × 8) 3-19. LEVER (BU LOCK) 6 lever (BU lock) 5 three hooks...
HCD-LF1 3-20. CLOSE LEVER 1 washer (3-1-0.4) 5 close lever 3 claw 2 close lever spring 4 shaft disc stop 3-21. DIR LEVER, GEAR (IDL-B) 2 claw 3 gear puley 4 gear (cap) 5 gear (IDL-A) 8 stopper 9 DIR lever q;...
HCD-LF1 SECTION 4 TEST MODE 4. TEST MODE Note 1: Regarding the notification symbol “R” The test mode is prepared in this product. Refer to item 5. TEST Because the number of the operating buttons of this product are MODE IN for the procedure how to enter the test mode, and to item limited, some operations require use of the operating buttons of 6.
Page 24
HCD-LF1 8. Key Test Mode 14. VACS ON/OFF Procedure: 1. Press the TEST MODE key (S301) inside the product or the RETURN O “R” button. 1. Press the TEST MODE key (S301) inside the product or the RETURN O “R” button.
Page 25
HCD-LF1 [OPERATING TEST MODE] DVD SECTION 0. SYSCON DIAGNOSIS [GENERAL DESCRIPTION] The same contents as board detail check by serial interface can be The Test Mode allows you to make diagnosis and adjustment easily checked from the remote commander operation.
Page 26
HCD-LF1 Check Items List: 1. DRIVE AUTO ADJUSTMENT 0-2. Version On the Test Mode Menu screen, press the 1 “R” key on the remote 0-2-1. All commander, and the Adjustment Menu will be displayed. 0-2-2. Revision ## Drive Auto Adjustment ## 0-2-3.
Page 27
HCD-LF1 EQ boost adjust Wait 500 msec Auto loop filter offset adjust Tracking on Auto track gain adjust Wait 500 msec Search Check Sled on 24. 32 track jump forward Check CLV lock 25. 32 track jump reverse Auto loop filter offset adjust, Auto focus adjust 26.
Page 28
HCD-LF1 FZC Count : The number of times which focus zero cross points Note: of each layer when lens down. 1. Set correctly the disc type to be used on the Disc PI Reference : The average of PI reference voltage. (hexadecimal Type screen.
Page 29
HCD-LF1 [1] LD [1] Focus Offset Turn on/off the laser. : Adjusts focus offset. [2] Focus [2] Focus Gain Search the focus and turn on the focus. : Adjusts focus gain. [3] SPDL [3] TRK. Offset Turn on/off the spindle.
Page 30
HCD-LF1 2-9. SACD Water Mark Check EEPROM Data 2/2 CDRW DVDRW SACD Water Mark Check Focus Gain Trk. Gain Focus Offset Trk. Offset PSP AMP Boost Next:UP Default:CLR Exit:RET Start: ENTER Stop: RETURN On this screen, current servo adjusted data stored in the EEPROM On this screen, measure the PSP AMP value and PSN value of SACD are displayed.
Page 31
HCD-LF1 • Clearing History Information aa: Initialization is completed or not. Clearing laser hours: : Complete. Press the DISPLAY “R” and CLEAR “R” keys in thisorder. other number : Not complete. Then both CD and DVD data are cleared. bb: Operating status of mechanism deck at an error occurred.
HCD-LF1 Ver 1.1 SECTION 5 ELECTRICAL ADJSTMENT DVD SECTION AUTO SERVO ADJUSTMENT After parts related to the servo circuit (RF amplifier (IC001), DSP (IC509), motor driver (IC501), EEPROM (IC903) so on) are replaced, re-adjusting the servo circuit is necessary. Select “ALL”...
HCD-LF1 Ver. 1.2 SECTION 6 DIAGRAMS • Circuit Boards Location THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams. For Printed Wiring Boards.
HCD-LF1 — MAIN SECTION — IC201 VIDEO AMP CR/B Cr out CB/R 4 CVBS in Cb out IC101 TO SA-WSLF1 T451 (SYSTEM CONNECTOR) DC/DC CONVERTER C in CY out FRONT-L C/CUBS 10 CY in CVBS out 6.5V DVD DSP CB/B...
HCD-LF1 • See page 65, 66 for IC Block Diagrams. • See page 62 for Waveforms. • See page 79 for IC Pin Function Description. 6-13. SCHEMATIC DIAGRAM — DMB07 SECTION (6/10) — (2/10) (Page 44) SAMBA_CTRL_BUS (6/10) (Page 45)
HCD-LF1 • See page 67 for IC Block Diagrams. 6-17. SCHEMATIC DIAGRAM — DMB07 SECTION (10/10) — (10/10) (LFE) BA33BC0FP-E2 NO MARK : DVD STOP HCD-LF1...
Page 67
HCD-LF1 IC302 PCM1609KPTR 32 31 30 36 35 34 33 VCC3 FUNCTION AGND3 CONTROL VCC4 INTERFACE AGND4 SYSTEM SCKI CLOCK SCKO MANAGER VOUT8 AGND6 VCC5 LRCK AGND5 TEST 4X/8X ENHANCED VOUT7 OVER SAMPLING MULTI- SERIAL DIGITAL LEVEL INPUT FILTER DELTA-...
Page 68
HCD-LF1 • IC Pin Function Description • DMB07 BOARD IC207 ZIVA5X-C1F (DVD SYSTEM PROCESSOR) Pin No. Pin Name Description VDDP — Power supply terminal (+3.3V) Address signal output to the programmable ROM and address latch Two-way data bus (address signal multiplexed) with the programmable ROM and...
Page 69
HCD-LF1 Pin No. Pin Name Description GND25 — Ground terminal MDQM2 Write mask signal output to the SD-RAM VDD25 — Power supply terminal (+3.3V) 88 to 95 MD20 to MD27 Two-way data bus with the SD-RAM GND25 — Ground terminal...
Page 70
HCD-LF1 Pin No. Pin Name Description AVDD2 — Power supply terminal (+3.3V) AVDD1 — Power supply terminal (+3.3V) AVSS1 — Ground terminal — Power supply terminal (+1.8V) — Ground terminal Audio system clock output to the A/D converter and digital audio processor LRCK L/R sampling clock signal (44.1 kHz) output to the digital audio processor...
Page 71
HCD-LF1 Pin No. Pin Name Description HCS0 Chip select signal output to the programmable ROM VDDP — Power supply terminal (+3.3V) TRST Reset signal input terminal (for JTAG) Data output terminal (for JTAG) Data input terminal (for JTAG) Not used...
Page 72
HCD-LF1 • DMB07 BOARD IC701 TMC57929PGF-RDP (DVD DECODER) Pin No. Pin Name Description 1, 2 D5, D6 Two-way data bus with the mechanism controller — Ground terminal Two-way data bus with the mechanism controller Address signal input from the mechanism controller —...
Page 73
HCD-LF1 Pin No. Pin Name Description Serial data request signal input from the DVD system processor and DSD XHAC decoder HINT Not used XS16 Not used Not used XPDI Not used VDDS — Power supply terminal (+5V) 59, 60 HA0, HA2 Not used —...
Page 74
HCD-LF1 Pin No. Pin Name Description RFIN RF signal input from the CD/DVD/SACD RF amplifier 118, 119 VCCA5, VCCA4 — Power supply terminal (+3.3V) VCOR1 — VCO oscillating range setting resistor connected terminal VCOIN VCO input terminal 122, 123 GNDA4, GNDA3 —...
Page 75
HCD-LF1 Pin No. Pin Name Description XTA2 System clock (33.8688 MHz) output terminal XTA1 System clock (33.8688 MHz) input from the clock generator — Power supply terminal (+3.3V) 172 to 176 D0 to D4 Two-way data bus with the mechanism controller...
Page 76
HCD-LF1 • DMB07 BOARD IC801 CXD2753R (DSD DECODER) Pin No. Pin Name Description VSCA0 — Ground terminal (for core) XMSLAT Serial data latch pulse signal input from the mechanism controller MSCK Serial data transfer clock signal input from the mechanism controller...
Page 77
HCD-LF1 Pin No. Pin Name Description PHREFI Phase reference signal input terminal for DSD output phase modulation Not used Phase reference signal output terminal for DSD output phase modulation PHREFO Not used ZDFL Front L-ch Zero data flag detection signal output terminal...
Page 78
HCD-LF1 Pin No. Pin Name Description WRFD Not used Operation clock signal input for PSP physical disc mark detection from the DVD decoder 124, 125 WAVDD0, WAVDD1 — A/D power supply terminal (+2.5V) (for PSP physical disc mark detection) Analog RF signal input for PSP physical disc mark detection from the CD/DVD/...
Page 79
HCD-LF1 • DMB07 BOARD IC901 CXP973064-245R (MECHANISM CONTROLLER) Pin No. Pin Name Description NO_USE Not used SDEN Serial data enable signal output to the CD/DVD/SACD RF amplifier Digital out on/off control signal output to the DSP and DSD decoder DOCTRL/ISBTEST “L”: digital out off, “H”: digital out on...
Page 80
HCD-LF1 Pin No. Pin Name Description SQCK Subcode Q data reading clock signal output to the DSP — Ground terminal CONTROL_2, 56, 57 Not used CONTROL_1 GFS_DVD Guard frame sync signal input from the DVD decoder MUTE_CD Muting on/off control signal output to the DSP “H”: muting on...
Page 81
HCD-LF1 • DVD-POW BOARD IC301 uPD703033BYGF-M57-3BA-A (SYSTEM CONTROLLER) Pin No. Pin Name Description UCOM-DO Ucom data output to Subwoofer UCOM-CLK Not used I2C-DATA 12c-data signal output to DVD system processor ZIVA-RST Reset signal output to DVD system processor I2C-CLK 12c-clock signal output to DVD system processor...
Page 82
HCD-LF1 Pin No. Pin Name Description — Not used — Not used QUA SI0 Touch key scan data output to touch key driver QUA SI1 Touch key scan data output to touch key driver QUA SI2 Touch key scan data output to touch key driver...
Page 83
HCD-LF1 Pin No. Pin Name Description V SW Mute signal output to the Video Amp V MUTE RCS signal output to the Video Amp — Not used — Not used AMPMCOM — Not used UCOM-DI Ucom data input to Subwoofer...
HCD-LF1 Ver. 1.2 SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Abbreviation The components identified by mark 0 or may have some difference from the original : Australian model dotted line with mark 0 are critical for safety.
HCD-LF1 Ver. 1.2 SECTION 8 ELECTRICAL PARTS LIST DISPLAY NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, uH: µH parts list may be different from the parts please include the board name.
Page 92
HCD-LF1 Ver. 1.2 DISPLAY DLED DMB07 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R468 1-216-841-11 METAL CHIP 1/10W C238 1-164-943-11 CERAMIC CHIP 0.01uF R469 1-216-841-11 METAL CHIP 1/10W R471 1-216-295-91 SHORT CHIP C239 1-164-943-11 CERAMIC CHIP 0.01uF...
HCD-LF1 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2004.08...