E Model Australian Model Chinese Model HCD-LF1H is control unit (DVD player) in DAV-LF1H. This system incorporates with Dolby* Digital and Dolby Pro Logic (II) Model Name Using Similar Mechanism adaptive matrix surround decoder and the DTS** Digital Surround System.
Page 2
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
HCD-LF1H Ver. 1.4 SECTION 1 3 7 63 1515 0 SERVICING NOTES Note about CDs/DVDs DISC SLOT LOCK The system can play CD-ROMs/CD-Rs/CD-RWs recorded in the The disc slot lock function for the antitheft of an demonstration following formats: disc in the store is equipped.
Page 5
HCD-LF1H 3 7 63 1515 0 • PRECAUTION FRONT PART The front part is easy to be scratched. Attach a protective sheet on the front part or remove the front part before the repair work. front part protective sheet •...
Page 6
HCD-LF1H 3 7 63 1515 0 • TO TAKE OUT DISC WHEN POWER SWITCH TURNS OFF (FORCE EJECT) 1. Load the disc using an external power supply. 1 Disconnect FFC 50P (160), and them remove the mech module (AUR-M1).
Page 7
HCD-LF1H 3 7 63 1515 0 • SERVICE POSITION (MECH MODULE (AUR-M1)) DMB14 board MAIN board FL board mech module (AUR-M1) L 13942296513 • SERVICE POSITION (DMB14 BOARD AND MAIN BOARD) mech module (AUR-M1) MAIN board FL board DMB14 board u163 http://www.xiaoyu163.com...
HCD-LF1H SECTION 2 This section is extracted 3 7 63 1515 0 GENERAL from instruction manual. Front Panel (control unit) Top Panel L 13942296513 A Soft-touch button indicators (42) I [/1 (on/standby) (42) B Front panel display (115) J Disc slot (42)
Page 9
HCD-LF1H 3 7 63 1515 0 Front Panel Display When playing back a DVD Lights up when the MOVIE or MUSIC mode is selected (page 47). Playing status Lights up when the system Lights up when the sleep outputs the progressive timer is set (page 82).
Page 10
HCD-LF1H 3 7 63 1515 0 Remote control N m/M (51) (51) TUNING –/+ (75) O REPEAT (58) P VOLUME +/– (42, 76, 98) TV VOL +/– (79) Q MUTING (42) R AUDIO (59) S PICTURE NAVI (53) T PROGRESSIVE (94)
HCD-LF1H SECTION 3 3 7 63 1515 0 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. • The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are completed.
HCD-LF1H 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-2. COVER (REAR) ASSY, HOLDER (HDMI) PRECAUTION THE MAIN UNIT DISASSEMBLY The front part is easy to be scratched. 1 cover (screw) Attach a protective sheet on the front...
HCD-LF1H 3 7 63 1515 0 3-9. DVD MECHANISM [MECH MODULE (AUR-M1)] SECTION-1 PRECAUTION DVD MECHANISM [MECH MODULE (AUR-M1)] DISASSEMBLY When removing the mech module (AUR-M1), create a solder bridge to prevent the optical pick-up from breaking. 6 two screws (+BVTP 3 ×...
HCD-LF1H 3 7 63 1515 0 3-10. DVD MECHANISM [MECH MODULE (AUR-M1)] SECTION-2 2 panel (CDM) 1 five claws L 13942296513 5 mech module (AUR-M1), bracket (CDM-L), etc. 3 four shafts (insulator) Do not hold the A part of mech module (AUR-M1).
HCD-LF1H SECTION 4 3 7 63 1515 0 TEST MODE 3. Disc Slot Lock Note 1: Regarding the notification symbol “R” The disc slot lock function for the antitheft of an demonstration Because the number of the operating buttons of this product disc in the store is equipped.
Page 24
HCD-LF1H Ver. 1.4 3 7 63 1515 0 8. RELEASING THE DEMO PLAY LOCK DVD SECTION Releasing Procedure : 9. Mirror Time Check 1. Press the ?/1 button to turn on the system. [TEST DISC LIST] 2. Insert the dedicated DEMO disc.
Page 25
HCD-LF1H Ver. 1.1 3 7 63 1515 0 9-4. MIRROR TIME ADJUSTMENT (2)Select “2. Drive Manual Operation”, by pressing the 2 “R” button. To enter Mirror Time Adjustment, press 5 “R” button on the remote Drive Manual Operation commander. The screen will appear as shown.
HCD-LF1H Ver. 1.3 SECTION 5 3 7 63 1515 0 ELECTRICAL ADJUSTMENT (12) Confirm the same values are displayed. If it is not same, DVD SECTION return to step (7). When the base unit is replaced, perform the adjustment and the MIRR time Adjust Menu measurement as shown below in this order.
Page 27
HCD-LF1H Ver. 1.2 SECTION 6 3 7 6 3 1 5 1 5 0 DIAGRAMS • Circuit Boards Location THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams.
HCD-LF1H Ver. 1.1 6-2. BLOCK DIAGRAM — MAIN SECTION — 3 7 6 3 1 5 1 5 0 IC601 VIDEO AMP CR/B Y in Cr out CB/R 4 CVBS in Cb out IC511 SYSTEM CONTROL T951 CY/G COARD...
Page 53
HCD-LF1H 3 7 63 1515 0 – DMB14 Board – IC501 AK4358VQ-L AVSS AVDD VREFH LOUT1– 1 LOUT1+ 2 ROUT4+ ROUT4– DZF3 3 DATT DATT DATT DATT DATT DATT DATT DATT DZF2 4 DZF1 5 Audio DIF0 CAD0 6...
Page 54
HCD-LF1H 3 7 63 1515 0 – DMB14 Board – IC706 BR24L16F-WE2 1 A0 16 K bit EEPROM ARRAY 11 bit 8 bit 2 A1 ADDRESS SLAVE WORD DATA 11 bit DECODER ADDRESS REGISTER REGISTER START STOP 3 A2...
Page 55
HCD-LF1H 3 7 63 1515 0 – MAIN Board – IC601 MM1623BFBE S-DC OUT 28 VCC2 S1/S2 27 S-DC OUT 150kΩ 75Ω VCC1 BIAS 6.75MHz DRIVER LOW-PASS C IN 26 C OUT FILTER MUTE 1 25 S1 CLAMP –6dB...
Page 56
HCD-LF1H 3 7 63 1515 0 • IC Pin Function Description DMB14 BOARD IC101 CXD9804R (CD/DVD RF AMP, FOCUS/TRACKING ERROR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description AGND — Ground terminal DVDA AC coupled input path A...
Page 57
HCD-LF1H 3 7 63 1515 0 Pin No. Pin Name Description SPFG Motor hall sensor input Mute signal control output IOPMON Power monitor signal input TG EJ SW Servo 1 signal input EEWP WF signal output to EEPROM (IC103) DVDD18 —...
Page 58
HCD-LF1H 3 7 63 1515 0 Pin No. Pin Name Description XIFSSY DQM signal input Data bus 7 from SD-RAM (IC104) DVSS — Ground terminal 117, 118 RD 6, 5 Data bus 6, 5 from SD-RAM (IC104) DVSS —...
Page 59
HCD-LF1H 3 7 63 1515 0 Pin No. Pin Name Description DVDD3 — Power supply (SW+3.3V) STBY MUTE signal output to Motor Driver (IC203) GVSW MUTE123 signal output to Motor Driver (IC203) REW signal output to Motor Driver (IC201) (not used)
Page 60
HCD-LF1H 3 7 63 1515 0 Pin No. Pin Name Description JITFN Negative input of operation amplifier for RF jitter meter (not used) PLLVSS — Ground terminal IDAC — Not used PLLVDD3 — Power supply (RF+3.3V) LPFON Negative output of loop filter amplifier...
Page 61
HCD-LF1H 3 7 63 1515 0 MAIN BOARD IC301 M30620MCP-A16FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description FL_DOUT FL serial data output FL_CLK FL serial clock output — Not used SIRCS_IN SIRCS input 5, 6 — Not used FL_LAT...
Page 62
HCD-LF1H 3 7 63 1515 0 Pin No. Pin Name Description STOP_KEY STOP KEY signal input PLAY_KEY PLAY KEY signal input 54 to 61 — Not used VCC2 — Power supply (BUP+ 3.3V) — Not used — Ground terminal 65 to 73 —...
HCD-LF1H Ver. 1.2 SECTION 7 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they : Mexican model The components identified by mark 9 contain may have some difference from the original : Russian model confidential information.
Page 79
HCD-LF1H 3 7 63 1515 0 US Model Canadian Model SERVICE MANUAL AEP Model UK Model E Model Ver. 1.1 2006.09 Australian Model SUPPLEMENT-1 Subject: Addition of “EXECUTING IOP MEASUREMENT” and “EMERGENCY HISTORY” for TEST MODE This SUPPLEMENT-1 describes the “EXECUTING IOP MEASUREMENT” and “EMERGENCY HISTORY”...
Page 80
HCD-LF1H TEST MODE 3 7 63 1515 0 8-4-2. EXECUTING IOP MEASUREMENT (5) Wait until a hexadecimal number appear. Manual Adjust In order to execute IOP measurement, the following standard procedures must be followed. 1. Track Balance Adjust: 2. Track Gain Adjust:...
Page 81
HCD-LF1H 3 7 63 1515 0 • Error Code 8-5-2. Clear the Emergency History Press TOP MENU “R” button and then press CLEAR “R” button. The error code for all emergency history would be reset. Emg.History Check Laser Hours...
Page 82
HCD-LF1H 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Need help?
Do you have a question about the HCD-LF1H and is the answer not in the manual?
Questions and answers