Bosch GBM 1600 RE Original Instructions Manual page 12

OBJ_BUCH-2420-003.book Page 12 Wednesday, July 27, 2016 1:18 PM
12 | English
Safety Warnings for Drills
 Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
 Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 Switch off the power tool immediately when the tool in-
sert jams. Be prepared for high reaction torque that
can cause kickback. The tool insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Additional safety warnings
 Do not use the power tool for explosive materials (e. g.,
easily inflammable solvents). Power tools produce
sparks which could ignite developing vapours.
 In case the power tool should fall into the material to be
stirred, pull the plug immediately and have the power
tool checked by an after-sales service agent. Material
that has penetrated the power tool can cause damage and
lead to an electric shock.
 Do not mix food. Power tools and their accessories are not
designed for processing food.
 Keep the cord away from the working area. The cord
may be entangled by the stirrer paddle.
 The mixing container must be suitable for mixing and
must stand securely. A container that is not properly se-
cured may move uncontrolled.
1 609 92A 2GV | (27.7.16)
 Ensure that no liquid splashes against the housing of
the power tool. Liquid that has penetrated the power tool
can cause damage and lead to electric shock.
 Follow the instructions and warnings in the Material
Safety Data Sheets (MSDS) of the material to be mixed.
Material to be mixed may be harmful.
 In the event of a power interruption, release the lock-
ing switch by pressing the on/off switch. This will pre-
vent the power tool from restarting unintentionally (risk of
injury).
 Do not use the power tool in a stand.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for drilling in wood, metal, ceramic
and plastic.
The machine is intended for mixing pulverised building mate-
rials such as mortar, plaster, adhesives, as well as solvent-
free paint, varnish and similar substances.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Key chuck*
2 Auxiliary handle (insulated gripping surface)
3 Thread for auxiliary handle
4 Auxiliary handle (insulated gripping surface)
5 Lock-on button for On/Off switch
6 On/Off switch
7 Rotational direction switch
8 Handle (insulated gripping surface)
9 Chuck key*
10 Securing screw for key type drill chuck
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Rotary drill
Article number
Rated power input
No-load speed
Rated torque
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
GBM 1600 RE
3 601 AB0 0..
W 850
-1
min 630
Nm 11
Bosch Power Tools