Table of Contents
Advertisement
Cleaning agent
en
The descaling programme can only be started once the
cooking compartment has completely cooled down. If
the temperature in the cooking compartment is too
high, a message appears on the display. Wait until the
cooking compartment has cooled down. Then restart
the process.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
Mix 500 ml water with 150 ml liquid descaler to
1.
make a descaling solution.
Press the On/Off button.
2.
Remove the water tank and fill with descaling
3.
solution.
Fully insert the water tank filled with the descaling
4.
solution.
Close the control panel.
5.
Press the Menu button.
6.
The operating modes menu opens.
Select the Descale operating mode.
7.
If you touch the "Next" field, information on the
cleaning operation is displayed.
The duration of the descaling programme is
displayed. It cannot be changed.
Press the "Start/Stop" button to start the cleaning
8.
operation.
The appliance is descaled. You can see the duration
counting down in the status bar. As soon as the
descaling programme has finished, an audible
signal sounds.
First rinsing cycle
Open the control panel.
1.
Remove the water tank, rinse thoroughly, fill with
2.
water and reinsert.
Close the control panel.
3.
Press the Start/Stop button to start.
4.
The appliance rinses. As soon as the rinsing cycle
has run through, a signal sounds.
Second rinsing cycle
Open the control panel.
1.
Remove the water tank, rinse thoroughly, fill with
2.
water and reinsert.
Close the control panel.
3.
Press the Start/Stop button to start.
4.
The appliance rinses. As soon as the rinsing cycle
has run through, a signal sounds.
Final cleaning
Open the control panel.
1.
Empty and dry the water tank.
2.
Switch off the appliance.
3.
Descaling is complete and the appliance is ready for
use again.
28
DCleaning agent
With good care and cleaning, your appliance will retain
C l e a n i n g a g e n t
its appearance and remain fully functioning for a long
time to come. We will explain here how you should
correctly care for and clean your appliance.
Suitable cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Depending on the appliance
model, not all of the areas listed may be on/in your
appliance.
Caution!
Risk of surface damage
Do not use:
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners,
■
Special cleaners for cleaning the appliance while it is
■
hot.
Wash new sponge cloths thoroughly before use.
Highly recommended cleaning and care products
Tip:
can be purchased through the after-sales service.
Observe the respective manufacturer's instructions.
:
Warning
Risk of burns!
The appliance becomes very hot. Never touch the
interior surfaces of the cooking compartment or the
heating elements. Always allow the appliance to cool
down. Keep children at a safe distance.
Area
Cleaning
Appliance exterior
Stainless steel
Hot soapy water:
front
Clean with a dish cloth and then dry with a soft
cloth.
Remove flecks of limescale, grease, starch and
albumin (e.g. egg white) immediately. Corrosion
can form under such flecks.
Special stainless steel cleaning products suitable
for hot surfaces are available from our after-sales
service or from specialist retailers. Apply a very
thin layer of the cleaning product with a soft cloth.
Plastic
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use glass cleaner or a glass scraper.
Painted surfaces
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Control panel
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use glass cleaner or a glass scraper.
Advertisement
Table of Contents
