Menus; Test Pool Pilot; View Setup; Owner Options - Aquacal DIG-220 Owner's Manual

Menus:

Salt
Salt Needed
Temperature
Cell V/A
Amp Hrs *
Software Version
Cell Type
Power Level
Pump Configuration
Pool Size
Reverse Time
Temp Adjust
Salt Adjust
Pump Prog 1 (if active)
Pump Prog 2 (if active)
Freeze Protect
* Only available when "Test Pool Pilot" is selected under "Maintenance" menu .
Test Pool Pilot (Diagnostic Menu):
1 Press MENU.
2 "Test Pool Pilot" is automatically displayed; then press SELECT .
3 The display will automatically toggle through the following displays (
the remaining displays and exit back to normal operation):
"Salt =XXXX ppm (X.x g/l)" (The optimum salt level is 3000 ppm (3.0 g/l). 4500 ppm for maximum chlorine production)
"Add Salt xx Lbs (xx Kg)" (The amount of salt needed to maintain 3000 ppm (3.0 g/l))
"Temperature XX° F (XX° C)" (The temperature of the water flowing through the Tri-sensor)
"Cell = XX V XX.x A" (The measured voltage and current sent to the Pool Pilot Cell)
"Amp-Hrs = xxxxxx" (The amount of amps received by the Pool Pilot Cell per hour) . This is only viewable if "Test Pool Pilot" was selected under the "Maintenance
Menu."
4. The controller will automatically leave the menu and revert to normal operation.
View Setup (Program and parameter menu to view the current programmed settings):
1. Press MENU, press
2. The display will automatically toggle through the following displays or pressing
will override the remaining displays and exit back to normal operation):
"Software V X.Xx" (The version number of Digital #DIG-200 software)
"Cell = XX-XX" (cell type: PPC1, PPC3, PPC4, PPC5)
"Power Level" (1-lowest, 2, and 3-highest; factory setting is 1)
Pump Configuration (External Timer, one-speed pump, two-speed pump, or remote runs pump. Factory setting is External Timer.)
"XX,XXX gallons( liters)" (The pool volume programmed in Installation Menu; 15,000 is the factory setting; page-22)
"Reverse = X hrs" (The reverse rate programmed in Installation Menu: 4-hrs is factory setting)
"Temp. adjust = X" (The temperature adjustment variation of actual Tri-sensor reading; page-22)
"Salt adjust + X %" (The salt calibration adjustment variation of actual Tri-sensor reading; page-22 )
"Pump program 1" (Only appears if pump control has been set to one-speed or two-speed)
"Pump program 2" (Only appears if pump control has been set to two-speed or two-speed)
Freeze protect (can only be enabled when the pump control is set to one-speed pump mode)
3. The DIG-220 will automatically leave the menu and revert to normal operation.

Owner Options:

1. Press MENU, press
2. Press or for desired selections, followed by SELECT
3. Once all modifications are complete, press

Select Language:

(Allows for personal preference language display)
1. Press or until "Select Language" is displayed; then press SELECT (English is the factory setting).
2. Press or until desired language "English," "Espanol," "Italiano", or "Francais," is displayed; then press SELECT .
20
PROGRAMMING
Test Pool Pilot (pg 20)
View Setup (pg 20)
Owner Options (pg 20)
Select Language
Select Units
Temperature Unit
12/24 Hour Clock
Set time of day
Pump Prog 1 (if active)
Pump Prog 2 (if active)
Exit Menu Mode
or until "View Setup" is displayed, then press SELECT .
or until "Owner Options" is displayed; then press SELECT .
or until "Exit Menu Mode" is displayed; then press SELECT. The menu will also time out after 20 seconds of no key activity.
(CONTINUED)

Test Pool Pilot

Set time of day
Pump Prog 1 (if active)
Pump Prog 2 (if active)
Force Reverse
Main Menu
Test Pool Pilot Set Reverse Time

View Setup

Replace Cell
Owner Options
Calibrate Temperature
Maintenance Menu Calibrate Salt
Installer Menu
Exit Menu Mode
Exit Menu Mode
Select Language
Select Units
Temperature Unit
12/24 Hour Clock
Set Pool Volume
Set cell type
Set cell power
Set pump control
Set time of day
Select remote
Select minerals
Pump Program 1 (if One or Two Speed Pump)
Pump Program 2 (if One or Two Speed Pump)
Enable Demo
Exit Menu Mode
or allows manual control forward and back. While in this feature, pressing MENU will override
or allows manual control forward and back. While in this feature, pressing MENU
Maintenance Menu (pg 21)
Installer Menu (pg 22)
Continued Next Page...