PIONEER DJ DJM-750MK2 Operating Instructions Manual page 15

REVERB
1
This function adds a reverberation effect to the input sound.
! Lowering the channel faders and cutting the input volume leaves a
delay sound.
Direct sound
Early reflected sound
Level
Reverberations
1%
100%
BEAT c, d buttons Sets the extent of the reverberation effect, from
1 – 100 %.
(parameter 1)
Use this to set the degree of the reverb effect.
TIME control (parameter 2)
1 – 100 (%)
LEVEL/DEPTH control Sets the balance between the original sound and the
(parameter 3) effect sound.
TRANS
The sound is cut according to the beat fraction set with the [BEAT c, d]
buttons.
Cut
1/1 beat
BEAT c, d buttons Sets the beat fraction between 1/16 and 16 with
(parameter 1) respect to 1 beat of BPM time.
Sets the effect time.
TIME control (parameter 2)
10 to 16000 (ms)
LEVEL/DEPTH control Sets the duty ratio and balance between the original
(parameter 3) sound and effect sound.
FLANGER
A 1-cycle flanger effect is produced according to the beat fraction set
with the [BEAT c, d] buttons.
Short delay
Cycle
Sets the effect time between 1/16 and 64 beats with
BEAT c, d buttons
(parameter 1) respect to 1 beat of BPM time.
Use this to set the cycle by which the flanger effect
TIME control (parameter 2) moves.
10 to 32000 (ms)
The further the control is turned clockwise, the more
LEVEL/DEPTH control the effect is stressed.
(parameter 3) When turned all the way counterclockwise, only the
original sound is output.
PITCH
Changes the pitch of the source sound.
BEAT c, d buttons Sets the pitch of the effect sound.
-50 to 100 (%)
(parameter 1)
Sets the pitch of the effect sound.
TIME control (parameter 2)
-50 to 100 (%)
LEVEL/DEPTH control Sets the pitch of the effect sound. Turn fully left to
(parameter 3) return to the original sound.
Time
Cut
Time
Time
ROLL
The sound being input at the point when the [ON/OFF] button is pressed
is recorded, and the recorded sound is output repeatedly according to
the beat fraction set with the [BEAT c, d] buttons.
Original
Effect turned on
1/1 roll
Repeated
BEAT c, d buttons Sets the effect time between 1/16 and 16 beats with
respect to 1 beat of BPM time.
(parameter 1)
Sets the effect time.
TIME control (parameter 2)
10 to 4000 (ms)
LEVEL/DEPTH control Sets the balance between the original sound and
(parameter 3)
ROLL.
VINYL BRAKE
The playback speed of the input sound changes according to the beat
fraction set with the [BEATc, d] buttons, slowing steadily, until play-
back stops.
BEAT c, d buttons Sets the effect time between 1/16 and 16 beats with
(parameter 1) respect to 1 beat of BPM time.
Sets the effect time.
TIME control (parameter 2)
10 to 4000 (ms)
Sets the playback speed of the input sound. Turn fully
LEVEL/DEPTH control left to return steadily to the original sound. Turn right
(parameter 3) from the fully left position to slow playback steadily,
resulting in an effect that stops playback.
HELIX
The sound being input at the point when the [ON/OFF] button is pressed
is recorded, and the recorded sound is output repeatedly according to
the beat fraction set with the [BEAT c, d] buttons.
Turn the [LEVEL/DEPTH] control right from the fully left position to
record the input sound. Also, turning it fully right fixes the output sound.
Altering the effect time changes the pitch of the sound recorded up to
that point.
BEAT c, d buttons Sets the effect time between 1/16 and 16 beats with
(parameter 1) respect to 1 beat of BPM time.
Sets the effect time.
TIME control (parameter 2)
10 to 4000 (ms)
Sets the ratio of sound overlay. Turn fully left to return
LEVEL/DEPTH control
to the original sound. Turn right from the fully left
(parameter 3)
position to record the input sound in its default state
1 When [1] to [4] is selected with the effect channel selector switch,
the effect sound cannot be monitored even if the [CUE] button of the
selected channel is pressed.
15
En