Summit FS21L Instruction Manual

Compact freezer
Hide thumbs Also See for FS21L:

Advertisement

Quick Links

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES
AND OPERATING INSTRUCTIONS. KEEP THIS MANUAL IN A SECURE LOCATION.
Write Serial Number (on back of unit) here:
_______________________________
COMPACT FREEZER
Model No.
Instruction Manual
FS21L
Felix Storch, Inc.
770 Garrison Avenue
Bronx, New York 10474
www.summitappliance.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FS21L and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Summit FS21L

  • Page 1 COMPACT FREEZER FS21L Model No. Instruction Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. KEEP THIS MANUAL IN A SECURE LOCATION. Felix Storch, Inc. Write Serial Number (on back of unit) here: 770 Garrison Avenue...
  • Page 2: Table Of Contents

    Reversing the Door Swing of Your Freezer ..........8 Locking the Freezer .................. 8 Troubleshooting ....................9 Limited Warranty .................... 11 TECHNICAL INFORMATION Model Number: FS21L Capacity: 1.42 cubic feet Electrical Rating: 110V AC / 60Hz Input Power: 87 watts...
  • Page 3: Important Safeguards

    IMPORTANT SAFEGUARDS Before the freezer is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the freezer, follow basic precautions, including the following: ...
  • Page 4  This unit is not designed to operate in enclosed spaces. When placing your unit, make sure you allow at least 4” of clearance on all sides.  Use two or more people to move and install freezer. Failure to do so can result in back or other injury.
  • Page 5: Location Of Parts

    LOCATION OF PARTS INSTALLATION  Installation of Your Unit Place your unit on a floor that is strong enough to support the unit when it is fully loaded. ● To level your unit, adjust the legs at the bottom. Allow 5 inches of space between the back and sides of the unit, which allows the proper ●...
  • Page 6: Operation

    OPERATION  Setting the Temperature Control  The cabinet temperature is controlled by the thermostat located at the back of the unit in the lower left corner. Rotate the dial to adjust the cabinet temperature.  The setting O indicates that the device is turned off. ...
  • Page 7: Food Storage

    CAUTION Do not use boiling water to speed defrosting because it may damage plastic parts. In addition, never use a sharp or metallic instrument to remove frost as it may damage the cooling system and will void the warranty. We recommend using a plastic scraper.
  • Page 8: Cleaning And Maintenance

    CARE AND MAINTENANCE  Cleaning Your Unit  Turn the temperature control to O, unplug the unit and remove the food and shelf.  Wash the inside with a solution of warm water and baking soda. The solution should consist of about 2 tablespoons of baking soda per quart of water. ...
  • Page 9: Reversing The Door Swing Of Your Freezer

    The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, you can refer to the diagram below. If you have a problem, call SUMMIT Customer Service at 1-800-932-4267.  Locking the Freezer Your freezer comes with two keys and a lock at the bottom center of the door.
  • Page 10: Troubleshooting

    The shelf or water drip tray are out of position. If your freezer shows other symptoms than those described above, or if you have checked all items listed as the cause and the problem still exists, then call SUMMIT® Customer Service at 1-800-932-4267...
  • Page 11 NOTES...
  • Page 12: Limited Warranty

    LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company.

Table of Contents