Table of Contents
Advertisement
B Adjusting the Color Temperature — COLOR TEMP ADJ Menu
Setting Lists in the COLOR TEMP ADJ Menu
This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see "About
menu numbers" on page 26(E).
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
[B] COLOR TEMP ADJ menu
Select the adjustment method.
MANUAL... : Set with the MANUAL adjustment
knob. ÷[B1]
PROBE... : Set using a probe. ÷[B2]
COPY... : Copy data from elsewhere. ÷[B3]
[B1] MANUAL menu
Adjust the gain and bias with the MANUAL
adjustment knob.
ADJUST... : Adjust the gain and bias. To shift
between gain adjustment and bias adjustment,
press UP/DOWN buttons. Use appropriate knobs
in each adjustment as described below. After the
adjustment, press the ENTER or Ent button to
confirm the adjusted values.
RED: CONTRAST KNOB (Adjust the R gain or
bias with the CONTRAST knob.)
GREEN: BRIGHT KNOB (Adjust the G gain or
bias with the BRIGHT knob.)
BLUE: CHROMA KNOB (Adjust the B gain or
bias with the CHROMA knob.)
LUMINANCE: PHASE KNOB (Adjust
luminance with the PHASE knob.)
To reset RED/GREEN/BLUE to the value
before adjustment
When you are adjusting the gain or bias using the
MANUAL adjustment knobs, you can reset the
setting to the one before adjustment by pressing the
corresponding MANUAL adjustment button
(BVM-D14H5U/D14H5E/D14H5A) or knob
(BVM-D9H5U/D9H5E/D9H5A).
To reset all of settings at the same time, press the
PHASE button or knob.
34
(E)
Note
You cannot reset the setting after you press the
ENTER or Ent button.
To access the MANUAL menu directly
When the [F2] button is assigned as the short-cut key
to the MANUAL menu, you can directly access the
MANUAL menu that corresponds to the color
temperature setting (STD/COL1/COL2) set to the
image on the screen.
For details of how to assign the short-cut key, see " [E]
Setting the Power-Up Conditions and Data about the Screen
Display — SYSTEM CONFIG Menu" on page 39(E).
[B2] PROBE menu
Select the probe for color temperature adjustment.
START: Start adjustment.
PROBE: Select the probe.
X: Enter the x coordinate.
Y: Enter the y coordinate.
2
LOW LIGHT (20IRE): Enter the luminance (cd/m
)
for low light.
HIGH LIGHT (100IRE): Enter the luminance (cd/
2
m
) for high light.
LOAD REF VALUE: Select the standard settings of
the x and y coordinates. ÷[B21]
[B21] LOAD REF VALUE
Select one of the followings:
D65: Use D65 setting (x and y coordinates and
standard luminance).
D93: Use D93 setting (x and y coordinates and
standard luminance).
[B3] COPY menu
Select one of followings: ÷ The current data, which is
used for adjusting, is copied.
STD: Copy STD data (factory setting: D65).
COL1: Copy COL 1 data (factory setting: D93).
COL2: Copy COL 2 data (factory setting: D65).
D65: Copy the color temperature of D65.
D93: Copy the color temperature of D93.
Note
The current data which is used for adjusting (selected
in the INPUT CONFIG menu) is displayed in blue
letters and you can not select it.
C
Setting the Input Configuration
— INPUT CONFIG Menu
Overview
You can set up to nine input channels.
Data pertaining to the input signals are set with the
INPUT CONFIG menu.
When a channel number (1 to 9) is entered with the
numeric keypad, it is then possible to set which input
connector on the rear panel will be assigned to that
channel number, and select the type of signal that will
be connected.
Assigning slot and connector numbers
Set which input connector on which slot will be
assigned to the current channel.
Assigning the signal type and format
The signal type and format which can be assigned to
each channel number vary, depending on what
adaptors are installed in the rear panel.
Structure of the INPUT CONFIG Menu
Level 1
Level 2
INPUT CONFIG (1/2)
CH x
FORMAT C1
YPBPR
RGB
NTSC, PAL
SLOT NO
D1-SDI
INPUT NO
HD-SDI
EXT SYNC SLOT
AUDIO INPUT
COLOR TEMP
APERTURE VALUE
CHANNEL NAME C 2
PROG
EDIT
CAM
VTR
NEW NAME
INPUT CONFIG (2/2)
CH x
1125/60I SYSTEM
H PHASE
MARKER PHASE
MARKER WIDTH
NTSC SET UP
YPBPR MATRIX
VCR MODE
To assign D1 serial digital signals
Serial digital signals can be assigned to the slot where
the BKM-120D is installed.
To assign analog composite signals
Analog composite signals can be assigned to the slot
where the BKM-127W is installed.
To assign HD serial digital signals
HD serial digital signals can be assigned to the slots
where the BKM-142HD is installed.
To assign analog component or RGB signals
Analog component or RGB signals can be assigned to
the slot where BKM-129X is installed.
35
(E)
Hide quick links:
Advertisement
Table of Contents
