Lenovo ideacentre All-In-One Y910 Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Desktop
  5. ideacentre All-In-One Y910
  6. Hardware maintenance manual
Lenovo ideacentre All-In-One Y910 Hardware Maintenance Manual

Lenovo ideacentre All-In-One Y910 Hardware Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

ideacentre All-In-One Y910 Computer
Hardware Maintenance Manual
Machine Types: F0CJ [AIO Y910-27ISH/Energy Star]

Advertisement

Table of Contents
loading

Related Manuals for Lenovo ideacentre All-In-One Y910

Summary of Contents for Lenovo ideacentre All-In-One Y910

  • Page 1 All-In-One Y910 Computer Hardware Maintenance Manual Machine Types: F0CJ [AIO Y910-27ISH/Energy Star]...
  • Page 3 All-In-One Y910 Computer Hardware Maintenance Manual Machine Types: F0CJ [AIO Y910-27ISH/Energy Star]...
  • Page 4 First Edition (August 2016)24th © Copyright Lenovo 2016. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925...

  • Page 5: Table Of Contents

    Selecting a startup device ..Replacing the camera module ..Exiting the Lenovo BIOS Setup Utility program . . Replacing the LCD panel module-None Touch . . Chapter 6. Symptom-to-FRU Index . . 19 Chapter 9.
  • Page 6 All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 7: Chapter 1. About This Manual

    Chapter 1. About this manual This manual contains service and reference information for Lenovo All-In-One Y910 computer listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect any attached power cords, telecommunication cables, network cables, and modem cables before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2016...
  • Page 10 – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Use caution; do not become a victim yourself. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 11: Safety Inspection Guide

    – Switch off power. – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potential hazards posed by these products. Each computer, as it was designed and built, had required safety items installed to protect users and service personnel from injury.

  • Page 12: Grounding Requirements

    • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlets. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 15: Chapter 3. General Information

    This chapter provides general information that applies to all computer models covered by this manual. Specifications This section lists the physical specifications for your computer. This section lists the physical specifications for your computer. Type Lenovo All-In-One Y910 This section lists the physical specifications. Environment Air temperature: Operating: 10°...
  • Page 16 All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2016...
  • Page 18 All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9).

  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.

  • Page 22: Selecting A Startup Device

    Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Lenovo BIOS Setup Utility program (see “Starting the Lenovo BIOS Setup Utility program” on page 13). 2. From the Lenovo BIOS Setup Utility program main menu, select the Startup option.

  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 25: Chapter 6. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor connections Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2016...

  • Page 26: Post Error Codes

    3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 27: Chapter 7. Locating Connectors, Controls And Components

    The following illustration shows the location of controls and components on the front of the computer. Attention: Be careful not to block any air vents on the computer. Blocked air vents can cause overheating. 1. 3D camera 3. 2D camera 4. Built-in microphone 2. Camera LED indicator © Copyright Lenovo 2016...
  • Page 28 8. Mic connector 3. Power button 9. USB 3.0 connector 4. USB 3.0 connector 10. USB 3.0 connector/USB power off charging connector 5. USB 3.0 connector 11. Optical drive eject button 6. Memory card reader ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...
  • Page 29 Rear view The following illustration shows the location of connectors and components on the rear of the computer. 1. HDMI-in connector 5. Ethernet connector 2. USB 2.0 connector 6. Power connector 3. USB 2.0 connector 7. Security cable slot 4. HDMI-out connector 8.
  • Page 30 24. Rear I/O bracket 9. Graphic card holder 25. Rear I/O board 10. Speaker system 26. EMI cover 27. Motherboard 11. System fan 12. Wi-Fi card 28. Main frame 13. Camera module 29. LCD panel ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...
  • Page 31 14. Microphone 30. Front cover 15. Power switch board 31. Bottom cover 16. Stand base Chapter 7 Locating connectors, controls and components...
  • Page 32 28. Battery 13. Rear I/O connector 29. DisplayPort connector 30. Power supply unit connector 14. ODD SATA connector 15. ODD power connector 31. Solid state drive slot 16. HDD SATA connector 32. Backlight connector ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 33: Chapter 8. Replacing Hardware

    Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo.

  • Page 34: Replacing The Keyboard And Mouse

    Remove any media from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug the cord from electrical outlet, and then disconnect the power cord from the connector on the computer, ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 35: Removing The Stand Base

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

  • Page 36: Removing The Rear Covers

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

  • Page 37: Replacing The Graphic Card

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.
  • Page 38 Reinstall the graphic card holder. Slide in the graphic card module into position and secure it to the chassis by fastening the screw in the graphic card holder. Step 11. Reattach the right rear cover. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 39: Replacing The Memory Module

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

  • Page 40: Replacing The Solid State Drive

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

  • Page 41: Replacing The Hard Disk Drive

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

  • Page 42: Replacing The Optical Drive

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.
  • Page 43 Step 6. Locate the optical removal notch, and then push the optical drive out using a screw driver . Step 7. Push a small iron stick (paper clip) into the small hole on the optical drive bezel so that the disk springs out as shown.

  • Page 44: Removing The Middle Cover

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 45 Step 8. Remove the optical drive. Refer to Replacing the optical drive. Step 9. Remove the seven screws that secure the middle cover to the chassis. Step 10. Lift up and remove the middle cover as shown. Chapter 8 Replacing hardware...

  • Page 46: Replacing The Power Switch Board

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 47: Replacing The Rear I/O Module

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 48 Step 13. Remove the four screws that secure rear I/O board to the bracket, and then slide the rear I/O board out. Step 14. To install the new rear I/O module: Align the holes in the new I/O board with the ones in the bracket. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 49: Replacing The System Fan

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 50: Removing The Stand Holder

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.

  • Page 51: Removing The Emi Cover

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 52: Replacing The Wi-Fi Card

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 53: Replacing The Heat-Sink

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 54 Attention: Place the heat-sink upside down on a flat surface to prevent thermal grease from contaminating other components. Attention: Use an alcohol pad to wipe the thermal grease off the CPU. Step 15. To install the new heat-sink: ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 55: Replacing The Motherboard

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 56: Replacing The Speaker System

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 57 Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Locating connectors, controls and components to locate the various connectors. Step 4.

  • Page 58: Replacing The Camera Module

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 59: Replacing The Lcd Panel Module-None Touch

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 60 Step 17. Remove the camera module. Refer to Replacing the camera module. Step 18. Remove the screw that secures the side I/O cover to the chassis, and then remove the side I/O cover. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...
  • Page 61 Step 19. Remove the eleven one screws that secure the main frame to the LCD panel. Step 20. Pull the front cover in the directions as shown until the LCD panel and front cover are separated. Step 21. Disconnect the LVDS cables from the connectors on the LCD panel. Step 22.
  • Page 62 Connect the LVDS and speaker system cables to the corresponding connectors on the motherboard. Step 23. Reattach the EMI cover, system fan, power switch board, rear I/O module, stand holder, middle cover, optical drive, hard disk drive, graphic card, rear covers and stand base. ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 63: Chapter 9. Fru Lists

    Chapter 9. FRU lists This chapter lists the information on the field replaceable units (FRUs) for ideacentre All-In-One Y910 desktop computers. Attention: Be sure to read and understand all the safety information before replacing any FRUs. Notes: FRUs that have a 1 or 2 in the CRU column are Customer Replaceable Units (CRUs).
  • Page 64 AIO Y910 IO/B cable CABLE 01AJ796 AIOY910 Power Switch Board CARDPOP 01AJ795 AIOY910 REAR IO Board CARDPOP 01EF492 Slide Door Left,Y910-27I DOOR 00XH608 USB Calliope KB BK JPN DT_KYB 01EF508 Rear IO Shielding,Y910-27I SHIELD ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...
  • Page 65 01EF498 GFX Card Shielding,Y910-27I SHIELD 00XL175 AIO Y910 LCD_CNVT cable CABLE 01EF499 GFX Card Holder,Y910-27I MECH_ASM 00XL031 Fru, LINECORD,CH,1.8M,3P,NON-LH LINECORD 00XL046 Fru, LINECORD,DK,1.8M,3P,NON-LH LINECORD 00XL042 Fru, LINECORD,AU,1.8M,3P,NON-LH LINECORD 01AH321 Intel SR300 3D camera CAMERA 00XL004 Fru,US/CA,1.8M,3P,NON-LH LINECORD 00XL183 AIO Y910 IO/B-GFX CARD cable CABLE 00XL006 Fru, US/CA,1.8M,3P,NON-LH...
  • Page 66 LINECORD 00XL009 Fru, LINECORD,CN,1.8M,3P,NON-LH LINECORD 00XL026 Fru, LINECORD,IL,1.8M,3P,NON-LH LINECORD 01EF513 Front Bottom Cover,Y910-27I MECH_ASM 01EF512 Front Bezel Sub Assy,Y910-27I MECH_ASM 00XH587 USB Calliope KB BK ENG DT_KYB 01AG709 4GB DDR4 2400 SoDIMM MEMORY ideacentre All-In-One Y910 Computer Hardware Maintenance Manual...
  • Page 67 00XL047 Fru, LINECORD,IT,1.8M,3P,NON-LH LINECORD 00XH588 DT_KYB USB Calliope KB BK ARA 01AG708 4GB DDR4 2400 SoDIMM MEMORY 01AG707 4GB DDR4 2400 SoDIMM MEMORY 01AG701 4GB DDR4 2400 SoDIMM MEMORY Chapter 9 FRU lists...
  • Page 68 All-In-One Y910 Computer Hardware Maintenance Manual...

  • Page 69: Chapter 10. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2016...

Table of Contents