Page 1
Operating Instructions and Parts Reference 2650 2655 B A L E B U S T E R 2650 - Serial Number 26CJ001150 & Up 2655 - Serial Number 26IJ000155 & Up roduct nformatIon nDusTrIes nTernaTIonal Po B 1940, J , nD 58402-1940 amesTown : (701) 252-4601•...
Page 2
DuraTech Industries International Inc. (DuraTech Industries) has made every effort to assure that this manual completely and accurately describes the operation and maintenance of the 2650 and 2655 BALEBUSTERS ™ as of the date of publication. DuraTech Industries reserves the right to make updates to the machine from time to time. Even in the event of such updates, you should still find this manual to be appropriate for the safe operation and maintenance of your unit.
Page 4
• Section 3.1, “Pre-Operation Inspection”. Appropriate use of unit Your model 2650/2655 BALEBUSTER is designed to load and shred most types of baled livestock forage. It is designed for use on large round bales. To avoid possible damage to the machine and risk of injury to the operator, consult with a DuraTech Industries International, Inc.
Page 5
The OPERATOR IS RESPONSIBLE for the safety of the operator and those in the surrounding area. Operators of the 2650/2655 BALEBUSTER are encouraged to wear head, eye, and ear protection, loose clothing is discouraged. 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
2650 / 2655 BALEBUSTER 2650 - Serial Number 26CJ001150 & Up 2655 - Serial Number 26IJ000155 & Up PART 1: Operating Instructions 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
The purpose of this owner’s manual is to explain maintenance requirements and routine adjustments for the most efficient operation of your 2650/2655 BALEBUSTER. There is also a trouble shooting section that may help in case of problems in the field. Any information not covered in this manual may be obtained from your dealer.
Page 12
This manual is organized into the following parts: • Part 1: Operating instructions explain how to set up, use and maintain the 2650/2655 BALEBUSTER. Part 2: Parts reference contains diagrams of each assembly, with the part number of each part. A key on •...
MANUAL PROVIDED WITH YOUR TRACTOR. THIS MACHINE IS NOT TO BE USED FOR ANY PURPOSE OTHER THAN THOSE EXPLAINED IN THE OPERATOR’S MANUAL, ADVERTISING LITERATURE OR OTHER DURATECH INDUSTRIES WRITTEN MATERIAL PERTAINING TO THE 2650/2655 BALEBUSTER. 1.1 Safety-alert symbols Decals are illustrated in Part 2: Parts Reference.
Page 14
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded. WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and includes hazards...
Do not operate a 2650/2655 BALEBUSTER when you are fatigued. Be alert - If you get tired while operating your 2650/2655 BALEBUSTER, take a break. Fatigue may result in loss of control. Working with any farm equipment can be strenuous.
Machine safety labels The safety decals located on your machine contain important information that will help you operate your equipment. Become familiar with the decals and their locations. DANGER: FLYING HAY, ROCKS, AND OTHER OBJECTS THROWN BY MACHINE. STAY CLEAR OF DISCHARGE SIDE OF MACHINE UNLESS OPERATOR HAS STOPPED TRACTOR ENGINE AND MACHINE HAS STOPPED ROTATING.
Page 17
6500322 • Replacement decals can be purchased from your Haybuster dealer. 2 6 5 0 / 2 6 5 5 B A L E B U S T E R O P E R A T I N G I N S T R U C T I O N S...
• Check periodically for breaks or unusual wear and make any necessary repairs. • Be sure the unit is securely attached to a tractor of equal or greater weight than the 2650/2655 BALEBUSTER and bale. • If required install P.T.O. safety chain, check local regulations regarding safety chain requirements.
• Never work on or near 2650/2655 BALEBUSTER unless engine is shut off and flails stopped. • Check periodically and tighten any loose bolts or connections.
Section 2: Dealer preparation 2.1 Pre-delivery inspection INSTRUCTIONS: Before delivering the machine, check the following items carefully and make corrections when necessary. Place an “X” in the box after each item has been checked and found to be acceptable. Check machine for missing items or damage in transit. Check for loose bolts or set screws.
The pin should be secured with a hairpin clip or suitable device to prevent the loss of the pin. Adjust the hitch so the machine will be parallel with the ground. Hitch the 2650/2655 BALEBUSTER to the tractor drawbar.
Page 24
10. Loosely assemble bearing #2000514 (with lock collar forward), on bracket using (4) ½ x 2-1/4 bolts #4800251, with (4) flat washers, lock washers, and nuts. 11. Slip drive shaft #8101074 thru bearing. Mount U-Joint #3600459 on drive shaft and chain case shaft using (2) 3/8 x 2-1/4 keys #6200020 and set 3/8 set screws #4800356.
Section 3: Operation To insure long life and economical operation, we highly recommend the operator of the 2650/2655 BALEBUSTER be thoroughly instructed in the maintenance and operation of the machine. There is no substitute for a sound preventative maintenance program and a well trained operator.
For your safety and the safety of others, you must use the following normal shut-down procedure before leaving the tractor controls unattended for any reason, including servicing, cleaning, or inspecting the 2650/2655 BALEBUSTER. A variation of the following procedure may be used if so instructed within this manual or your tractor manual or if an extreme emergency requires it.
figure 3.1 P.T.O. shield, working (lowered) position, latched maintenance (raised) position. P.T.O. shield hold down latch P.T.O. shield maintenance (raised) position P.T.O. shield working (lowered) position 3.3.3 Conveyor Speed Control Moving the lever on the conveyor speed control valve counterclockwise will slow the conveyor and make a finer product.
3.3.4 Conveyor Chain Adjustment The three chain tensioning bolts should be adjusted to allow lifting the slats 1” to 1-1/2” above conveyor deck. These bolts are located, on the front of the conveyor, at the center, and on the rear. Bolts must be adjusted evenly. center conveyor chain left conveyor chain adjustment bolt...
3.3.6 Slugbar Adjustment Exposing, less flail will create a finer cut and use less horsepower, while exposing more flail will produce a coarser cut. This is accomplished by rotating the slugbar adjustment handle. Rotating the handle counterclockwise will expose more flail, clockwise will expose less flail.
3.3.9 Stripper Plate Stripper Plate for the 2650 Adding a stripper plate will produce a finer cut and removing plates will produce a courser cut. For a finer cut, one or two additional stripper plates can be added.
3.3.10 Loader WARNING: Loader tines may swing down unexpectedly as they drop over center. They can move faster than you can react. Keep all bystanders away from the machine while loader is raised. figure 3.3 Loader Tines loader tine loader wing loader transport The loader has three settings for different size bales.
Page 32
loader tine left outer left inner right inner right outer Tine mounting brackets These settings are accomplished by removing the pivot bolts and removing the tine. After the tine is reinstalled in the proper position, reinstall the pivot bolt and tighten. Be sure the bolt threads protrude though the entire nut so that the locking nut functions properly.
3.3.11 Loader Transport Pin WARNING: Never stand under loader when removing transport pins. Do not attempt to force pins out, with the loader fully raised they can be easily removed. The loader transport pins can be inserted into three positions: Upper hole: Holds the loader in the fully raised position for transport.
3.3.14 Rack The rack has two positions: transport and working. The rack should travel between the two positions freely under the operator’s own power. All pivoting connections should be snug, but still allow the points to hinge freely. Inspect for cracked or excessively worn holes at the connections.
3.3.16 Changing distribution pattern The deflector can be positioned for creating a windrow, spreading, bunkfeeding, or stockpiling. Lower the deflector for a narrower windrow and raise the deflector for a wider spread. To change the position, pull the release lever, Rotate the deflector to the desired position and release the handle. A wider deflector belt (PN 8100819) is available for bunk feeding or additional material control.
To assure adequate braking and steering control, the tractor must have a weight greater than or equal to the weight of the 2650/2655 BALEBUSTER and any bales it will transport. To hitch the 2650/2655 BALEBUSTER to a tractor, perform the following steps: Adjust the tractor drawbar so that the distance from the end of the P.T.O.
DANGER: After making all necessary hook-ups to tractor, be sure rotor chamber is clear of any solid objects. Make sure any bystanders are away from the 2650/2655 BALEBUSTER before engaging P.T.O., conveyor or loader. Flying objects can cause serious injury or death. Stay clear of discharge side of machine unless operator has stopped tractor engine and machine has stopped rotating.
Page 38
Engage the P.T.O.. CAUTION: Engaging the P.T.O. with the tractor engine speed above an idle may damage the drive line components and the tractor P.T.O.. Increase tractor engine speed until the P.T.O. speed reaches 1000 RPM. Listen for noise and watch for vibration.
DANGER: If it is necessary to transport a second bale over uneven terrain, make sure any bystanders are away from the 2650/2655 BALEBUSTER. Serious injury or death could result if the bale rolls off the loader main frame loader supports.
Reverse direction only if bale is lodged or hesitates to turn. DANGER: If it is necessary to transport a second bale over uneven terrain, make sure any bystanders are away from the 2650/2655 BALEBUSTER. Serious injury or death could result if the bale rolls off the main frame loader supports.
WARNING: Never stand under loader when removing transport pins. Do not attempt to force pins out, with the loader fully raised they can be easily removed. To prepare the 2650/2655 BALEBUSTER for transport, perform the following steps: Raise the loader and move the loader transport pins to the desired position.
Clean all mud, dirt, grease and other foreign material from the exterior of the machine. Cut all twine off from around the rotor. Wash the complete machine. If washing the 2650/2655 BALEBUSTER with a high pressure washer, keep the nozzle away from the sealed bearings. To inhibit rusting repaint places where bare metal is exposed.
Section 4: Lubrication The operator should make a check of all grease fittings on the unit before beginning to operate it so as to become familiar with their location and the correct service schedule. WARNING: Use normal shut-down procedure (page 17) before lubricating machine. 4.1 Lubrication Use only a high quality, #2 multi-purpose grease when lubricating the unit.
Page 44
PTO stand lubrication P.T.O. universal joint figure 4.1 point 1 of 1 lubrication point 1 of 3 P.T.O. lubrication (ref. 6) (ref. 2) P.T.O. telescoping shaft (ref. 3) P.T.O. universal joint lubrication point 2 of 3 (ref. 2) figure 4.2 rotor bearing lubrication point front and rear rotor...
Page 45
figure 4.4 chain case lubrication point #2 chain case lubrication chain case lubrication point #1 figure 4.5 chain case lubrication chain case lubrication point #3 2 6 5 0 / 2 6 5 5 B A L E B U S T E R O P E R A T I N G I N S T R U C T I O N S...
Page 46
figure 4.6 roller chain lubrication roller chains- apply a graphite lubricant to roller chains after every 15 hours of use figure 4.7 loader lubrication points #1 loader lubrication #1 loader lubrication #2 2 6 5 0 / 2 6 5 5 B A L E B U S T E R O P E R A T I N G I N S T R U C T I O N S...
Page 47
figure 4.8 loader lubrication points #2 loader lubrication #4 loader lubrication #5 figure 4.9 loader lubrication points #3 loader lubrication #1 loader lubrication #3 2 6 5 0 / 2 6 5 5 B A L E B U S T E R O P E R A T I N G I N S T R U C T I O N S...
Clean all mud, dirt, grease and other foreign material from the exterior of the machine. Cut all twine off the rotor. Wash the entire machine. If washing the 2650/2655 BALEBUSTER with a high-pressure washer, keep the nozzle away from the sealed bearings. Repaint places where bare metal is exposed.
Section 5: Troubleshooting PROBLEM CAUSE REMEDY 1. No Capacity 1. Bale turning to slow. 1. Open conveyor speed control valve. 2. Bale Does Not Turn 1. Bale lodged in feeder 1. Reverse rotation of slat conveyor. 3. Excessive Vibration 1. Build up of twine on rotor. 1.
Section 6: 2650/2655 Balebuster Options Grain tank Operation (Option) WARNING: DO NOT climb into hopper, you could become trapped or injured by rotating augers. Before operating the “Grain tank” make sure all shields are in place. The grain tank is used for top-dressing feed supplements or can be use independently for supplement feeding.
WARNING: DO NOT attempt to fill hopper by climbing on the machine. The hopper lid can be opened and closed easily from the ground, by moving the hopper lid handle up for an open lid or down for a closed lid. The auger extension tube lowers and raises in and out of operating position automatically when the rack is folded and unfolded.
Page 52
* This chart is for a baseline setting only and should not be considered accurate because of variances in tractor hydraulic flows and pressures. The hopper must be recalibrated if the tractor is changed. 2 6 5 0 / 2 6 5 5 B A L E B U S T E R O P E R A T I N G I N S T R U C T I O N S...
Page 53
Line 1. The amount of hay that is fed to each animal, in pounds, on a daily basis. Example: Each animal is fed 40 lbs. of hay each day. Line 2. The amount of feed supplement that is fed to each animal, in pounds, on a daily basis. Example: Each animal is fed 5 lbs.
6.3 Hydraulic Deflector (Option) The hydraulic deflector moves the rack and deflector from transport position to working position. Connecting the hydraulic hoses to the tractor gives the operator control of the deflector from inside the tractor. Rack and deflector in transport position Rack and deflector in working position 2 6 5 0 / 2 6 5 5 B A L E B U S T E R O P E R A T I N G I N S T R U C T I O N S...
6.4 Hydraulic Slug Bar (Option) The hydraulic slug bar raises and lowers the slug bars as needed for your processing condition. Connecting the hydraulic hoses to the tractor gives the operator control of the slug bars from inside the tractor. Hydraulic slug bar cylinder shown in the lowest position Hydraulic slug bar cylinder shown in the highest raised position...
Section 7: Maintenance Welding Procedure Balebuster Welding Procedures For Machines With The Weigh Scale Option Precautions are required for welding on machines with electronic components. Electronic components including but not limited to: electronic scales Proper welding procedures are necessary in order to avoid damage to the components, their sensors, and associated components.
Appendix A: WARRANTY Duratech Industries International Inc. warrants to the original purchaser for one year from purchase date that this product will be free from defects in material and workmanship when used as intended and under normal maintenance and operating conditions. This warranty is limited to the replacement of any defective part or parts returned to our factory in Jamestown, N.D., within thirty (30) days of failure.
Appendix C: Grain tank (Option) Specifications Option Wt..................650 lbs (approx) Hopper Capacity ....................21 bu Max Weight Capacity ..................1300 lbs Max supplement Delivery rate ..............3.5 bu/min Hyd. Press. Req .....................1500 psi Hyd. Flow Req....................8 gpm 2 6 5 0 / 2 6 5 5 B A L E B U S T E R O P E R A T I N G I N S T R U C T I O N S...
2 6 5 0 S H R E D D E R A S S E M B L Y - F R O N T 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 62
“SHLD\REAR\SHRDR\2650” 8101341 RTR\FLAIL\78-3/8\2650 8101094 SHAFT\SLUGBAR\2650 8101313 PAN\DISH\ADJ 8101095 DOOR\SHREDDER\2650\ 77-1/4” 8101512 DOOR\SHRDR\2650\71-1/4” sn 26EJ151150 AND UP 8101100 FRM\SHRDR\RH 8101747 FRM\SHRDR\RH sn 26HJ461150 AND UP 8101748 BRKT\STRG\JACK NOT SHOWN 8100118 FLAIL\DUMMY\256 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
2 6 5 0 S H R E D D E R A S S E M B L Y - D O O R 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 64
“SHLD\REAR\SHRDR\2650” 8101341 RTR\FLAIL\78-3/8\2650 8101094 SHAFT\SLUGBAR\2650 8101313 PAN\DISH\ADJ 8101095 DOOR\SHREDDER\2650\ 77-1/4” 8101512 DOOR\SHRDR\2650\71-1/4” sn 26EJ151150 AND UP 8101100 FRM\SHRDR\RH 8101747 FRM\SHRDR\RH sn 26HJ461150 AND UP 8101748 BRKT\STRG\JACK NOT SHOWN 8100118 FLAIL\DUMMY\256 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
2 6 5 0 S H R E D D E R A S S E M B L Y - S L U G B A R 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 66
“SHLD\REAR\SHRDR\2650” 8101341 RTR\FLAIL\78-3/8\2650 8101094 SHAFT\SLUGBAR\2650 8101313 PAN\DISH\ADJ 8101095 DOOR\SHREDDER\2650\ 77-1/4” 8101512 DOOR\SHRDR\2650\71-1/4” sn 26EJ151150 AND UP 8101100 FRM\SHRDR\RH 8101747 FRM\SHRDR\RH sn 26HJ461150 AND UP 8101748 BRKT\STRG\JACK NOT SHOWN 8100118 FLAIL\DUMMY\256 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
2 6 5 0 S H R E D D E R A S S E M B L Y - R O T O R 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 68
“SHLD\REAR\SHRDR\2650” 8101341 RTR\FLAIL\78-3/8\2650 8101094 SHAFT\SLUGBAR\2650 8101313 PAN\DISH\ADJ 8101095 DOOR\SHREDDER\2650\ 77-1/4” 8101512 DOOR\SHRDR\2650\71-1/4” sn 26EJ151150 AND UP 8101100 FRM\SHRDR\RH 8101747 FRM\SHRDR\RH sn 26HJ461150 AND UP 8101748 BRKT\STRG\JACK NOT SHOWN 8100118 FLAIL\DUMMY\256 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
2 6 5 0 S H R E D D E R A S S E M B L Y - F L O O R P A N ( S . N . 2 6 - H J - 4 6 1 1 5 0 & U P ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 70
“SHLD\REAR\SHRDR\2650” 8101341 RTR\FLAIL\78-3/8\2650 8101094 SHAFT\SLUGBAR\2650 8101313 PAN\DISH\ADJ 8101095 DOOR\SHREDDER\2650\ 77-1/4” 8101512 DOOR\SHRDR\2650\71-1/4” sn 26EJ151150 AND UP 8101100 FRM\SHRDR\RH 8101747 FRM\SHRDR\RH sn 26HJ461150 AND UP 8101748 BRKT\STRG\JACK NOT SHOWN 8100118 FLAIL\DUMMY\256 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
L O A D E R A S S E M B L Y 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 82
L O A D E R A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 3800082 FTG\LUB\1/4NFXZERK\ADAPT 4800056 PIN\HAIR\3/16(#3) 4800633 BOLT\HEX\1X5-1/2\NC\GR5\PLT 4900127 NUT\TPLCK\1\NC 8100794 PIN\LOCK\TRANSPORT 8101513 FRM\LOADER\LOWER\ 8101115 LOADER\UPPER\ D1015651 BRKT\WING\LOADER 8101311 BOLT\HEX\1X5-1/2\GREASE 8101312 BOLT\HEX\1X6-1/2\GREASE 8101352 BOLT\HEX\1X6\GREASE 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
L O A D E R T I N E S 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 84
L O A D E R T I N E S ITEM PART QTY. PART DESCRIPTION 4800471 BOLT\HEX\1X7\NC 4900031 NUT\HEX\1\NC 5000053 WASH\LOCK\1 8101033 TINE\SQ\LEFTHAND 8101075 TINE\SQ\RIGHTHAND 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
R A C K A N D D E F L E C T O R A S S E M B L Y 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 86
R A C K A N D D E F L E C T O R A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 2000811 CLLR\LOCK\3/4 4800003 BOLT\HEX\3/8X1 4800178 BOLT\HEX\1/2X1-3/4 4800351 BOLT\HEX\1/2X2-3/4 4900001 NUT\HEX\1/2\NC 4900002 NUT\HEX\3/8\NC 4900014 NUT\TPLCK\1/2\NC...
2 6 5 0 C O N V E Y O R A S S E M B L Y ( S . N . U P T O 2 6 - H J - 4 6 1 0 5 0 ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 88
2 6 5 0 C O N V E Y O R A S S E M B L Y ( S . N . U P T O 2 6 - H J - 4 6 1 0 5 0 ) ITEM PART QTY.
2 6 5 0 C O N V E Y O R A S S E M B L Y ( S . N . 2 6 - H J - 4 6 1 1 5 0 & U P ) 2 6 5 5 C O N V E Y O R A S S E M B L Y ( S .
Page 90
2 6 5 0 C O N V E Y O R A S S E M B L Y ( S . N . 2 6 - H J - 4 6 1 1 5 0 & U P ) 2 6 5 5 C O N V E Y O R A S S E M B L Y ( S .
Page 91
2 6 5 0 D R I V E C H A I N A S S E M B L Y ( S . N . T H R U 3 6 1 0 5 0 ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 92
LOCK COLLAR FOR 2001041 8101067 DRV\CHAIN\ASSY\2650 D R I V E C H A I N A S S E M B L Y - C H A I N R O U T I N G 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
2 6 5 0 D R I V E C H A I N A S S E M B L Y ( S . N . 3 6 1 1 5 0 T H R U 4 0 1 0 5 0 ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 94
SHFT\DRV\CHAIN\PTO 8101713 HSG\CHAIN\W-FLG-BRG\2650 D R I V E C H A I N A S S E M B L Y - C H A I N R O U T I N G 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
2 5 6 0 D R I V E C H A I N A S S E M B L Y ( S . N . 4 0 1 1 5 0 T H R U 2 6 1 0 5 5 9 0 5 0 ) 2 6 5 5 D R I V E C H A I N A S S E M B L Y ( S .
Page 96
SHFT\DRV\CHAIN\PTO 8101713 HSG\CHAIN\W-FLG-BRG\2650 D R I V E C H A I N A S S E M B L Y - C H A I N R O U T I N G 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
S T A N D A R D D R I V E L I N E A S S E M B L Y 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 100
HOSE MINDER 8101071 LATCH\SHLD 8101072 SHLD\PTO 8101073 BRKT\BRG\PTO\2650 8101074 SHFT\DRV\PTO 8101076 MNT\SHLD\DRV 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
C O N S T A N T V E L O C I T Y D R I V E L I N E A S S E M B L Y 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 102
C O N S T A N T V E L O C I T Y D R I V E L I N E A S S E M B L Y ITEM PART QTY. PART DESCRIPTION 8101827 DRV\ASSY\CV 3600684 PTO\44E\CAT5\80CV\21SP\1-3/8>...
2 6 5 0 W H E E L A N D B E A R I N G ( T H R U S . N . 2 6 1 0 5 5 9 0 5 0 ) 2 6 5 5 W H E E L A N D B E A R I N G ( T H R U S . N . 2 6 I J 0 0 8 5 5 ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 106
2 6 5 0 W H E E L A N D B E A R I N G ( T H R U S . N . 2 6 1 0 5 5 9 0 5 0 ) 2 6 5 5 W H E E L A N D B E A R I N G ( T H R U S . N . 2 6 I J 0 0 8 5 5 ) ITEM PART QTY.
P T O A S S E M B L Y # 3 6 0 0 4 5 9 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 110
P T O A S S E M B L Y # 3 6 0 0 4 5 9 ITEM PART QTY. PART DESCRIPTION 3600459 PTO\252-21797\44R 3600115 440 CROSS AND BEARING KIT 3600363 SLIDE LOCK YOKE ASSY 3600364 YOKE & SHAFT 3600334 3600368 YOKE,TUBE,SLIP SLEEVE 3600369...
P T O A S S E M B L Y # 3 6 0 0 6 8 4 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 112
P T O A S S E M B L Y # 3 6 0 0 6 8 4 ITEM PART QTY. PART DESCRIPTION 3600369 YOKE 36-334 2544 3600604 CROSS&BRG\44E\WSLR 3600605 CROSS&BRG\CAT5\80DEG\CV 3600684 PTO\44E\CAT6\80CV\21SP\1-3/8> 3600685 PTO\HALF\MACHINE\3600684 3600686 PTO\HALF\TRACTOR\3600684 3600689 YOKE\44E\1-3/8CV-21SPLINE\SSL 3600701 CENTER HOUSING 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
H Y D R A U L I C H O S E S A N D F I T T I N G S 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 114
H Y D R A U L I C H O S E S A N D F I T T I N G S ITEM PART QTY. PART DESCRIPTION 3800483 FTG\3/4MORX3/4MJICX3/4MJIC\RUN;TEE 3800694 FTG\3/4FOR\QUICK;CPLR\FEMALE 3900025 MOTOR\HYD\17.9\H\AMNT\7/8FOR\1SHFT 4000213 VALVE\CONTROL\FLOW\3/4MOR 4100273 CYL\HYD\4-1/2X24\1-3/4 -CANADIAN TOOL & DIE 4100223 SEAL KIT for 4100273 4100272...
O R B I T M O T O R ITEM PART NUMBER DESCRIPTION 3900025 Mtr\Hyd\17.9\H\A;MNT\7/8for o-ring thread 3900002 Mounting Flange 6200011 Key, Woodruff 7501038 Seal Kit 3900033 Mtr\Hyd\14.1\7/8FOR 7501038 Seal Kit 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
F L O W C O N T R O L V A L V E ITEM PART QTY. PART DESCRIPTION 4000213 Flow Control Valve, o-ring thread 4000031 Handle Assembly 3 & 4 4000091 Seal\Kit\FlowControl 4000034 Snap Ring 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
F L O W C O N T R O L V A L V E 4 0 0 0 3 3 1 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 118
F L O W C O N T R O L V A L V E 4 0 0 0 3 3 1 ITEM PART NO. DESCRIPTION 4000331 VALVE\FLW-CRTL\#8FOR 3 & 8 4000334 HDL\ASSY\V\HYD 5,10,11, & 13 4000335 SEAL\KIT\V\HYD (INCLUDES 2 EACH OF 5,10,11, & 13) 4000336 SNAP RING\V\HYD 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
O P T I O N A L H Y D R A U L I C D E F L E C T O R 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 120
MNT\CYL\SHRDR\DFLCTR 8101096 BRKT\STOP\HYD\LOADER 8101097 BRKT\LATCH\DFLCTR 8101098 BRKT\STRAP\RACK\HOOK\2650 8101146 MNT\DFLCTR\W-INDEX 8101114 CNTRL\DEFL\HYD\KIT\2650 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
O P T I O N A L H Y D R A U L I C D E F L E C T O R - D E T A I L A 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 122
MNT\CYL\SHRDR\DFLCTR 8101096 BRKT\STOP\HYD\LOADER 8101097 BRKT\LATCH\DFLCTR 8101098 BRKT\STRAP\RACK\HOOK\2650 8101146 MNT\DFLCTR\W-INDEX 8101114 CNTRL\DEFL\HYD\KIT\2650 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
O P T I O N A L H Y D R A U L I C D E F L E C T O R - D E T A I L B 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 124
MNT\CYL\SHRDR\DFLCTR 8101096 BRKT\STOP\HYD\LOADER 8101097 BRKT\LATCH\DFLCTR 8101098 BRKT\STRAP\RACK\HOOK\2650 8101146 MNT\DFLCTR\W-INDEX 8101114 CNTRL\DEFL\HYD\KIT\2650 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
O P T I O N A L H Y D R A U L I C D E F L E C T O R - D E T A I L C 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 126
MNT\CYL\SHRDR\DFLCTR 8101096 BRKT\STOP\HYD\LOADER 8101097 BRKT\LATCH\DFLCTR 8101098 BRKT\STRAP\RACK\HOOK\2650 8101146 MNT\DFLCTR\W-INDEX 8101114 CNTRL\DEFL\HYD\KIT\2650 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
O P T I O N A L H Y D R A U L I C S L U G B A R 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 128
KEY\SQ\3/8X1-1/2\HARDEND 8101779 MNT\CYL\SHRDR\SLGBR 8101780 MNT\CYL\HYD\SLGBR\2650 8101781 CNTRL\SLGBR\HYD\KIT\2650 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
O P T I O N A L S H R E D D E R E X T E N S I O N 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 130
O P T I O N A L S H R E D D E R E X T E N S I O N ITEM PART QTY. PART DESCRIPTION 4800003 BOLT\HEX\3/8X1 4800156 BOLT\HEX\3/8X3 4900002 NUT\HEX\3/8\NC 5000001 WASH\FLAT\3/8 5000019 WASH\LOCK\3/8 8101177 EXT\SHRDR\77-1/2 2 6 5 0 / 2 6 5 5 B A L E B U S T E R...
O P T I O N A L W I D E D E F L E C T O R B E L T 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 132
O P T I O N A L W I D E D E F L E C T O R B E L T ITEM PART QTY. PART DESCRIPTION 4800003 BOLT\HEX\3/8X1 4900002 NUT\HEX\3/8\NC 5000001 WASH\FLAT\3/8 5000019 WASH\LOCK\3/8 8100819 BELT\DFLCTR\18 x 73-3/4 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
O P T I O N A L T A I L L I G H T - F E N D E R M O U N T I N G 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 136
CLAMP\CUSH\HD\1/2 NOT SHOWN 7500700 LOOM\POLY\SPLIT\3/8 7500835 LOOM\POLY\SPLIT\1/2 Note: Mount taillight as far forward as possilbe to avoid contact with loader frame. 2650 - S.N. 2610559150 & UP 2655 - S.N. 2610014655 & UP ITEM PART QTY. PART DESCRIPTION 4800003 BOLT\HEX\3/8X1...
O P T I O N A L F E N D E R 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 140
O P T I O N A L F E N D E R ITEM PART QTY. PART DESCRIPTION 4800350 BOLT\HEX\5/8X2-1/4 4900005 NUT\HEX\5/8\NC 5000003 WASH\LOCK\5/8 8100827 FNDR\2620\RT 8100828 FNDR\2620\LT Note- Optional Fenders can not be used with Optional Floatation Tires. 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
G R A I N T A N K ( O P T I O N ) A S S E M B L Y ( O - R I N G ) - D E T A I L S A & B 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
G R A I N T A N K ( O P T I O N ) A S S E M B L Y ( O - R I N G ) - T A N K D E T A I L S 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
G R A I N T A N K ( O P T I O N ) H Y D R A U L I C S D E T A I L S ( O - R I N G ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 146
G R A I N T A N K ( O P T I O N ) H Y D R A U L I C S D E T A I L S ( O - R I N G ) ITEM PART QTY.
2 6 5 0 S T R I P P E R B A R ( O P T I O N ) I N S T A L L A T I O N 2 6 5 5 S T A N D A R D S T R I P P E R B A R I N S T A L L A T I O N 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 148
2 6 5 0 S T R I P P E R B A R ( O P T I O N ) I N S T A L L A T I O N 2 6 5 5 S T A N D A R D S T R I P P E R B A R I N S T A L L A T I O N ITEM PART QTY.
W E I G H S C A L E ( O P T I O N ) ( L O A D C E L L ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 150
W E I G H S C A L E ( O P T I O N ) ( L O A D C E L L ) ITEM PART QTY. PART DESCRIPTION 4800011 BOLT\HEX\3/4X3-1/2 4800063 BOLT\HEX\3/4X4 4800200 BOLT\L\3/4X5-1/4X8-1/4 4900004 NUT\HEX\3/4\NC 5000005 WASH\FLAT\3/4...
F L O A T A T I O N T I R E ( S T A N D A R D ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 152
F L O A T A T I O N T I R E ( S T A N D A R D ) ITEM PART QTY. PART DESCRIPTION 2600849 WHL\IMP-2\ASSY\14LX16.1 Includes 2 each of items 1 and 2 2600846 TIRE\14LX16.1\8PLY 2600652 WHL\6-BOLT\16.1X11...
A X L E E X T E N S I O N S ( O P T I O N ) 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 154
A X L E E X T E N S I O N S ( O P T I O N ) ITEM PART QTY. PART DESCRIPTION 4800350 BOLT\HEX\5/8X2-1/4 4900005 NUT\HEX\5/8\NC 5000003 WASH\LOCK\5/8 8101267 AXLE\EXTENSION\12” 8101276 EXTENSION\AXLE\KIT 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
D E C A L L O C A T I O N S 6500041 6500304 6500034 6500356 6500362 6500035 6500034 6500039 6500038 6500144 6500070 6500435 6500322 6500267 6500351 OR 6500441 6500267 6500361 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 158
D E C A L L O C A T I O N S 6500434 6500040 6500490 6500085 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
Page 159
A Tradition of Innovation Since 1966 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...
2650/2655 BALEBUSTER Documentation Comment Form DuraTech Industries welcomes your comments and suggestions regarding the quality and usefulness of this manual. Your comments help us improve the documentation to better meet your needs. • Did you find any errors? • Is the information clearly presented? • Does the manual give you all the information you need to operate the equipment safely and effectively? • Are the diagrams and illustrations correct? • Do you need more illustrations?
Page 161
Please fill out the delivery report on the following pages. The white copy is to be returned to: DuraTech Industries International Inc. P.O. Box 1940 Jamestown, ND 58402-1940 The yellow copy is the dealer copy; the pink copy is to be retained by the customer. 2 6 5 0 / 2 6 5 5 B A L E B U S T E R P A R T S R E F E R E N C E...