Specifications - Dremel 200 Original Instructions Manual

side forces applied to these wheels may cause them to
shatter.
b. For threaded abrasive cones and plugs use only
undamaged wheel mandrels with an unrelieved
shoulder flange that are of correct size and length.
Proper mandrels will reduce the possibility of breakage.
c. Do not "jam" a cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth
of cut. Overstressing the wheel increases the loading and
susceptibility to twisting or snagging of the wheel in the cut
and the possibility of kickback or wheel breakage.
d. Do not position your hand in line with and behind the
rotating wheel. When the wheel, at the point of operation,
is moving away from your hand, the possible kickback may
propel the spinning wheel and the power tool directly at
you.
e. When wheel is pinched, snagged or when interrupting
a cut for any reason, switch off the power tool and
hold the power tool motionless until the wheel comes
to a complete stop. Never attempt to remove the cut-off
wheel from the cut while the wheel is in motion otherwise
kickback may occur. Investigate and take corrective action
to eliminate the cause of wheel pinching or snagging.
f. Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter the
cut. The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
g. Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
h. Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
SAFETY WARNINGS SPECIFIC FOR WIRE BRUSHING
OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b. Allow brushes to run at operating speed for at least one
minute before using them. During this time no one is to
stand in front or in line with the brush. Loose bristles or
wires will be discharged during the run-in time.
c. Direct the discharge of the spinning wire brush away
from you. Small particles and tiny wire fragments may be
discharged at high velocity during the use of these brushes
and may become imbedded in your skin.
d. Do not exceed 15,000 RPM when using wire brushes.
DO NOT WORK WITH MATERIALS
WARNING
!
CONTAINING ASBESTOS (ASBESTOS IS
CONSIDERED CARCINOGENIC).
TAKE PROTECTIVE MEASURES WHEN
WARNING
!
DURING WORK DUST CAN DEVELOP
THAT IS HARMFUL TO ONE'S HEALTH,
COMBUSTIBLE OR EXPLOSIVE (SOME DUSTS ARE
CONSIDERED CARCINOGENIC); WEAR A DUST MASK AND
WORK WITH DUST/CHIP EXTRACTION WHEN CONNECTABLE.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EC COUNTRIES
Do not dispose of power tools with household waste!
According the European Guideline 2012/19/EC for
Waste Electrical and Electronic Equipment and its
implementation into national law, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally-correct manner.

SPECIFICATIONS

GENERAL SPECIFICATIONS
200
Rated Power (W) 125
230-240 V,
Voltage Rating
50 Hz
Collet Capacity 0.8 mm, 1.6 mm, 2.4 mm, 3.2 mm
Rated Speed (n) 35,000
RPM
Class II
Double insulated construction tools
Construction
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
MOTOR SPECIFICATIONS
Only 3000
This multitool utilizes a variable high speed motor. It is wired
for operation on 230 V, 50 Hz. Always check that the supply
voltage is the same as the voltage indicated on the nameplate
of the tool.
ALWAYS UNPLUG MULTITOOL BEFORE CHANGING
ACCESSORIES, CHANGING COLLETS, OR SERVICING THE
TOOL.
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range
of Dremel accessories and attachments allow you to perform
a large variety of tasks. These include tasks such as sanding,
carving, engraving, routing, cleaning and polishing.
PICTURE: 2-5
A. Collet nut
B. Collet
C. Housing cap or EZ
Twist™ integrated
wrench/nose cap
D. Shaft lock button
E. On/Off switch
F. Hanger
G. Power cord
H. Brush cover
I. Ventilation openings
J. Variable speed dial
K. Collet wrench
19
3000 4000
130 175
230 V, 230-240 V,
50 Hz 50-60 Hz
33,000 35,000
RPM RPM
ASSEMBLY
GENERAL
EZ information
Only 4200
L. EZ Change levers
M. EZ Change chuck
4200
175
220-240 V,
50-60 Hz
33,000
RPM