Du Pont WFQT13000 Series Installation Instruction Manual page 12

STEP 5
-Optional Direct Connect
Install the QuickTwist
1 B
Hold the QuickTwist Filter with the label facing to the left slightly. The two nozzles on top of the QuickTwist
™
toward the back of the QuickTwist
1
out to each side. See Figure 6
2
Lift the QuickTwist ™ Filter straight up into the System Head
on top of the QuickTwist ™ Filter are fully engaged into the System Head.
3
Turn the QuickTwist ™ Filter from right to left until it stops.
STEP 6
-Optional Direct Connect
Test the Filter System for Proper Operation
1
Turn on the cold water shut-off valve under the sink.
2
Turn on the new Faucet for Filtered Water
from the QuickTwist ™ Filter, allow the water to run for approximately 10 minutes.
3
Check for any leaks between the System Head assembly and Filter; around all fittings; on Kitchen Faucet dapter
and on faucet/tubing connection.
If there are leaks between the System Head assembly and the QuickTwist
n
Turn off the cold water shut-off valve to the Filter System and turn on the Faucet for Filtered Water to drain the water and release pressure.
n
Remove the QuickTwist ™ Filter and inspect the O-Rings around the nozzles on top of it. Make sure they are in place and free from dirt and particles.
n
Turn off the Faucet for Filtered Water.
n
Replace the QuickTwist ™ Filter by lifting it straight up into the System Head until the two nozzles seat into the ports and the two extended flanges on top of the QuickTwist
engaged into the System Head. Turn the QuickTwist
n
Turn the cold water supply valve back on and turn on the Faucet for Filtered Water.
If there are leaks around the fittings:
n
Turn off the cold water shut-off valve to the Filter System to release pressure in the System.
n
While pulling the 1/4" Plastic Tubing
is not scratched. If the 1/4" Plastic Tubing is unevenly cut or scratched, cut off 1/2" to 5/8" and re-install the Plastic Tubing (see Step 5 of Installation Instructions).
n
Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.
If there are leaks on the Kitchen Faucet dapter connection:
n
Turn off the cold water shut-off valve to the Filter System to release pressure in the System.
n
Locate the Kitchen Faucet dapter.
• If the 1/4" Plastic Tubing is leaking, follow the previous steps ("If there are leaks around the fittings").
• If the thread between the Kitchen Faucet dapter and the kitchen faucet stem is leaking, tighten more securely. If leaking continues, disconnect the 1/4" Plastic Tubing and remove the
Kitchen Faucet dapter. Wrap the Kitchen Faucet dapter and the threaded faucet stem with plumber's tape and re-install (see Step 2 of Installation Instructions).
• If the thread between the Kitchen Faucet dapter and the cold water supply line is leaking, tighten more securely. If leaking continues, disconnect the 1/4" Plastic Tubing and remove the
Kitchen Faucet dapter. Wrap the Kitchen Faucet dapter and the cold water supply line with plumber's tape and re-install (see Step 2 of Installation Instructions).
n
Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.
‰ If leaks continue, turn off the water supply and call Customer Service or your local plumber.
‰ For Filter Replacement Instructions please see page 9.
WFQT13000 & WFQT13500 Series
™ Filter
™ Filter. If holding properly, the two extended flanges on top of the QuickTwist
at right.
until the two nozzles seat into the ports and the two extended flanges
D
. In order for the Filter System to flush out any air and carbon fines (fine black powder)
™
™ Filter counter-clockwise until it stops.
L
with one hand, press in on the grey collar around the inlet and/or outlet fitting. Check to make sure that the 1/4" Plastic Tubing is cut squarely and that it
Filter should be
™
™ Filter should be
H
connection;
Filter:
12
5
1
2
B
3
™ Filter are fully
V4.0