Remove The Top Board Assembly (L) . (See Procedure - Yamaha Clavinova CLP-265GP Service Manual

4. Circuit Boards & Assemblies (Main Unit)
(Time required: About 6 minutes each)
4-1

Remove the top board assembly (L) . (See procedure 2.)

4-2 Remove the top board assembly (S). (See procedure 3.)
4-3 Each circuit board and assembly can be removed by
removing its fixing screws as shown in table1. (Fig.4, Table 1)
5. Key Cover Assembly
(Time required: About 6 minutes)
5-1 Remove the top board assembly (L) . (See procedure 2.)
5-2 Remove the top board assembly (S). (See procedure 3.)
5-3 Remove the screw marked [S03] for each side.
The rack covers L and R can then be removed. (Fig.5)
5-4 Set both ends of the rod to the slits of the rack and then
lift the rear portion of the key cover assembly. (Fig.6)
5-5 Lean the key cover assembly slightly, and remove the
guide pins from the guide rail. At that time, it is noted
not to damage the side cover. (Fig.6)
* When assembling, be sure not to make scratches on the
side cover assembly.
* When assembling, set both ends of the rod to the slits of
the rack accurately.
Rack Cover L
Key Cover Assembly
[S03]: Bind Head Tapping Screw-B 3.0X8 MFZN2W3 (WE774300)
(Fig.5)
Key Cover Assembly
(Fig.6)
6.
6-1
6-2
6-3
6-4
6-4-1 Remove the screw marked [4A]. (Fig.7)
6-4-2 Remove the two (2) hexagonal nuts marked [6] and the
6-4-3 Remove the two (2) screws marked [7A]. The AJACK
6-5
6-5-1 Remove the three (3) screws marked [4B]. (Fig.7)
6-5-2 Remove the two (2) screws marked [7B]. The DJACK
7.
7-1
7-2
[S03]
7-3
7-4
7-5
Key Cover Assembly
[4A,B]: Bind Head Tapping Screw-B 3.0X8 MFZN2W3 (WE774300)
[5]:
[6]:
[7A,B]: Bind Head Tapping Screw-B 3.0X8 MFZN2W3 (WE774300)
Arm Assembly
AJACK & DJACK Circuit Boards
(Time required: About 7 minutes)
Remove the top board assembly (L) . (See procedure 2.)
Remove the top board assembly (S). (See procedure 3.)
Remove the jack assembly. (See procedure 4.)
AJACK Circuit Board
two (2) washers marked [5]. (Fig.7)
circuit board can then be removed from the jack
assembly. (Fig.7)
DJACK Circuit Board
circuit board can then be removed from the jack
assembly. (Fig.7)
MA80S Circuit Board
(Time required: About 8 minutes)
Remove the top board assembly (L) . (See procedure 2.)
Remove the top board assembly (S). (See procedure 3.)
Remove the MA cover. (U model only)(See procedure 4.)
Remove the MA80S assembly. (See procedure 4.)
Remove the five (5) screws marked [1], the three (3)
screws marked [2] and the screw marked [3]. The
MA80S circuit board can then be removed from the
MA80S assembly. (Fig.8)
[4A] [5][6] [4B]
[7B] [7A] [7A]
Washer BLACK (VJ869400)
Special Nut M12X14X2 P=1.0 (WF559900)
(Fig.7)
CLP-265GP
Jack Assembly
AJACK
DJACK
[7B]
7