1. Manuals
  2. Brands
  3. Spectrum Manuals
  4. Indoor Furnishing
  5. Freedom XRS Elite
  6. Owner's manual

Spectrum Freedom XRS Elite Owner's Manual

Lectern
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
Freedom XRS Elite Lectern
55289
XRS Elite with surround, keyboard tray,
and rack cabinet installed on left
(shown retracted)
Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Any parts damaged during shipment must be reported
within 15 days of receipt. To report information regard-
ing missing parts or damage, to purchase parts or
accessories, or if you have any questions, please
contact us.
Thank you for purchasing Spectrum products!
Spectrum Industries, Inc
925 First Avenue, Chippewa Falls, WI 54729 USA
800 235 1262
715 723 6750
www.spectrumfurniture.com
™
XRS Elite with overbridge, keyboard tray,
and rack cabinet installed on right
(shown extended)
0118857 Page 1 of 18

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Freedom XRS Elite and is the answer not in the manual?

Questions and answers

Related Manuals for Spectrum Freedom XRS Elite

Summary of Contents for Spectrum Freedom XRS Elite

  • Page 1 15 days of receipt. To report information regard- ing missing parts or damage, to purchase parts or accessories, or if you have any questions, please contact us. Thank you for purchasing Spectrum products! Spectrum Industries, Inc 925 First Avenue, Chippewa Falls, WI 54729 USA 800 235 1262 715 723 6750 www.spectrumfurniture.com...
  • Page 2 Note: The Freedom XRS Elite Lectern is not designed for use with cord reels or surface-mount cord reel accessories.

  • Page 3: Assembly & Set-Up

    Assembly / Setup 1. Unloading lectern Utility knife Note: Upon receiving lectern, inspect packaging for damage. To report informa- tion regarding damages, please call 1-800-235-1262 within 15 days of receipt. 1. Cut and remove banding using a utility knife, scissor, or other cutting tool. 2.

  • Page 4: Normal Operation

    2. Lectern lift mechanism initial setup, operation, and reset procedure Preparation: Control buttons • Read all instructions before operation. • Make sure lectern is plugged-in using the 15-foot, 15-amp power cord. • Locate the “Up” and “Down” control buttons. Control pad is located on the instructor- side under the worksurface front edge on opposite side from rack cabinet.
  • Page 5 3. Install 3-piece skirt Note: The skirt has been designed to be installed tool-free with the lectern upright. Do not tip the lectern to install. 1. Position the audience-side skirt as shown and hook the (3) pre-installed screws into the (3) keyhole slots. Figure 3A. 2.

  • Page 6: Quick-Release Door

    Rack Cabinet - optional The removable rack cabinet (14RU front, 10RU rear) simplifies installation and provides the ability to integrate equipment remotely, and docked into the lectern at a later date. Figure 4A. Detaching Cabinet 1. To detach the rack cabinet from the lectern, unlock the cabinet lock pawl near the floor.
  • Page 7 Flip-up shelf operation - optional Phillips screwdriver Operation The shelf will automatically lock into place when lifted into the horizontal position with the levers released. Figure 6A. To lower or flip-up the shelf, press and hold the levers under each folding shelf bracket at the same time while slowly lowering or raising the shelf.
  • Page 8 Overbridge insert panel - optional 4mm hex Drill wrench 1. To remove the overbridge insert panel, remove the (2) 1/4-20 x 35mm JC bolts with a 4mm hex wrench and lift out the panel. Figure 7A. Measuring Drill bit 2. To make cutouts in the insert panel [optional]: device A.
  • Page 9 Freedom XRS Elite Lectern overbridge insert panel blank (flat view) 2” Grommet 2” Grommet Max cutout area Figure 7B Overbridge Section view B-B Worksurface Worksurface opening below ™ Note: The Overbridge Control Console has been designed for many of the cur-...

  • Page 10: Wiring Diagram

    Wiring Diagram Actuator Actuator Up / Down buttons Control box Note: Power cord can be plugged into a power strip (not included) inside lectern. To wall outlet Figure 8A Note: A separate power strip is recommend- ed (not included) to plug the control box and other power plugs into.
  • Page 11 Note: Leave enough slack in the cords and wires from the rack cabinet to pull the rack cabinet out from the lectern. Cords and wires from Rack Cabinet Rack Cabinet Figure 8C Bottom view Rack cabinet 2” Grommets for floor power access Figure 8D 0118857 Page 11 of 18...
  • Page 12 Caster operation 1. Lock the brake levers to lock movement of the casters. (Two instructor-side casters only). Figure 9. 2. To resume operation, lift up on brake levers. Brake lever Figure 9 Note: The skirt should be removed to prevent skirt damage if the lectern will be moved over large floor transitions, or thresholds.
  • Page 13 • Removable back panel • Wire management slots in tray • Acrylic panel in door • Max 1 tray per Freedom XRS Elite • Customer-installed • Customer-installed Front rack rail: 14RU Slides: Pull out 8”...
  • Page 14 Overbridge Insert Panel with cutouts - 96504mod • Two power receptacles • For overbridge version only • Two USB charge ports (not data-compatible) • Contact Spectrum to specify cutout size(s) and location(s) • Thumbscrew clamps • Overbridge not available separately • Requires worksurface cutout •...

  • Page 15: Safety Information

    Electric leg information Warning! Only for EU markets • This appliance can be used by children aged from 8 years and above and persons Failure to comply with these instructions may result in accidents involving serious personal injury. with reduced physical, sensory or mental capabilities or lack of experience and Failing to follow these instructions can result in the product being damaged or being destroyed.
  • Page 16 Misc. on the DESKLINE® DL5/DL6 system Electrical connection of the DL5/DL6 system This system is a DESKLINE system developed for desks and for indoor use in offi ces. Do not The DESKLINE® DL5/DL6 system is to be connected as shown on fi gure 4. Each DL5/ use it in industrial kitchens or in other enviroments that have to be cleaned with aggressive DL6 is to be connected to the sockets on the control box by means of the motor cables, detergents.
  • Page 17 Freedom XRS Elite Troubleshooting Guide Symptom Problem Solution Loss of power Be sure control box is plugged into a live circuit. Make sure all electrical connections are securely plugged into the control box. Loose electrical connections See wiring diagram on p.9 for reference.

  • Page 18: Warranty

    P.A.C.E. program (Product Assurance to meet Customer Expectations). We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table below from the date of delivery.

Table of Contents