1. Manuals
  2. Brands
  3. ClearView Manuals
  4. Security Camera
  5. IPD-81A
  6. Operation manual

ClearView IPD-81A Operation Manual

Hide thumbs Also See for IPD-81A:
Table of Contents

Advertisement

Quick Links

Network Camera Web3.0 Operation Manual
Version 1.0.1
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IPD-81A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ClearView IPD-81A

Summary of Contents for ClearView IPD-81A

  • Page 1 Network Camera Web3.0 Operation Manual Version 1.0.1...

  • Page 2: Table Of Contents

    Table of Contents Network Config ..........................1 Network Connection ..................... 1 Log in ..........................1 Live ..............................6 Encode Setup ........................ 6 System Menu ......................... 7 Video Window Function Option .................. 7 Video Window Setup ....................8 2.4.1 Image Adjustment ..................... 8 2.4.2 Original Size ......................
  • Page 3 5.1.1 Conditions ....................... 30 5.1.2 Video ........................41 5.1.3 Audio ........................53 Network ......................... 56 5.2.1 TCP/IP ........................56 5.2.2 Connection ......................58 5.2.3 PPPoE ........................60 5.2.4 DDNS ........................61 5.2.5 IP filter ........................62 5.2.6 SMTP （e-mail) ..................... 63 5.2.7 UPnP ........................
  • Page 4 5.5.6 Remote control ......................131 5.5.6 Auto Maintenance ....................132 5.5.7 Upgrade ........................ 133 Information ......................... 133 5.6.1 Version ........................133 5.6.2 Log ........................134 5.6.3 Online User ......................134 Alarm ............................136 Log out ............................138...
  • Page 5 Important The following functions are for reference only. Some series products may not support all the functions listed below.

  • Page 6: Network Config

    1 Network Config 1.1 Network Connection Network camera and PC connection mainly has two ways, see Figure 1- 1 and Figure 1-2. Figure 1- 1 Figure 1-2 Before you access network camera via the Internet, you need to have its IP address. User can use Config Tool to search IP of the network camera.
  • Page 7 After successful connection, the login interface is shown as in Figure 1-3; input your user name and password. Default factory username is admin and password is admin. Figure 1-3 The system will display “Update Password” prompt box for your first login, users need to modify the password and save it properly.
  • Page 8 Figure 1-5 Click on “Please click here to download and install the plug-in”. The system pops up warning information to ask you whether run or save this plug-in. See Figure 1-6. Figure 1-6...
  • Page 9 You must either run or save the file to local and install it. Follow the following steps. Click on run, you will see Figure 1-7and Figure 1-8. Figure 1-7...
  • Page 10 Figure 1-8 When plug-in installation completes, the installation page closes automatically. The web-end will refresh automatically, and then you can view video captured by the camera. Figure 1-9...

  • Page 11: Live

    2 Live After you logged in, you can see the live monitor window. See Figure 2-1. Figure 2-1 There are four sections:  Section 1: Encode setup bar  Section 2: System menu  Section 3: Window function option bar ...

  • Page 12: System Menu

    Parameter Function Click it to enable main stream video monitoring and click again Main stream to disable it. Generally for storage and monitor. Click it to enable Sub Stream 1 video monitoring and click again Sub Stream 1 to disable it. When network bandwidth is insufficient, it substitutes main stream for monitoring.

  • Page 13: Video Window Setup

     When the video is in the original status, click it you can Digital select any zone to zoom in. In the non-original status, Zoom you can drag the zoom-in zone in specified range. Right click mouse to restore previous status. ...

  • Page 14: Original Size

    Figure 2-6 Click this button to display/hide image control interface. Click it to open picture setup interface. This interface is on the top right pane. Please refer to the following sheet for detailed information. Parameter Function Video It is to adjust monitor video Note: setup brightness.

  • Page 15: Width And Height Ratio

    2.4.4 Width and Height Ratio Click it to restore original ratio or suitable window. 2.4.5 Fluency Adjustment There are three levels of fluency for you to select (Realtime, Normal, and Fluency). The default is normal. 2.4.6 Rules Info Click the button, preview image will display intelligent rules after enabling; it is “enable” by default. 2.4.7 Zoom and Focus Click this button and the focus zooming interface appears on the right of preview interface, as shown in Figure 2-7, click left mouse button to adjust focus zooming configuration.
  • Page 16 Parameter Function Adjust the focal length of the lens by clicking or long pressing “+”“-”buttons. Zoom Step length is used to adjust the length of one step with one click. Adjust the sharpness of the lens by clicking or long pressing“+”、“-” buttons. Focus Step length is used to adjust the length of one step with one click.
  • Page 17 Figure 2-8 parameter Note Installation Mode Three modes which are ceiling mount, wall mount and ground mount. It represents the display mode of the current image (default supports original image mode), the display modes may be different according to different installation modes.
  • Page 18 parameter Note 360°expanded rectangular panorama +6 independent sub image, both the sub image and the subbox in the expanded rectangular panorama support zoom and 1P+6 movement, for the expanded rectangular panorama also supports left and right starting point movement. Original image + 8 independent sub images, both the sub image and the subbox in the original image support zoom and movement.
  • Page 19  1P: Original picture  1P+3: Original picture and three trigger track windows, it can adjust the location and size of three trigger track windows on the original picture.  1P+5: Original picture and five trigger track windows, it can adjust the location and size of five trigger track windows on the original picture.

  • Page 20: Ptz Control

    3 PTZ Control Here you can view direction keys, speed, zoom, focus, iris, preset, tour, pan, scan, pattern, aux on, off and PTZ setup button. See Figure 3-1. Note: Before PTZ operation, please make sure you have properly set PTZ protocol. (Please refer to Ch. 5.5.3). Currently only IPC-HFXXXX series and –PT series products can support PTZ function.

  • Page 21: Scan

    Figure 3-2 PTZ setting interface is shown as in Figure 3-3. Here you can set scan, preset, tour, pattern, assistant function and light and wiper plus view coordinate. Figure 3-3 3.1 Scan Scan interface is shown in Figure 3-4.

  • Page 22: Preset

    Figure 3-4 Steps to scan are: Step 1. Click on Set button, display icon. Step 2. Move via direction key to select left, click on Set Left to set left border of camera Step 3. Move via direction key to select right, click on Set Right to set right border of camera. Step 4.

  • Page 23: Pattern

    Tour interface is shown in Figure 3-6. Figure 3-6 Steps to tour are: Step 1. In tour box, input tour path value. Step 2. Click on Add. Range of tour relates to PTZ protocol. Step 3. In preset box, input preset value. Step 4.

  • Page 24: Assistant

    Click “Stop Rec” to complete the setting of a pattern path. Step 4 Click “Start” and it will start pattern according to the pattern spot which has been set; click “Stop” and the pattern ends. 3.5 Assistant Assistant interface is shown in Figure 3-8. Figure 3-8 Steps to assistant are: Step 1.

  • Page 25: Playback

    4 Playback Web client playback supports video playback and picture playback. Note: Before playback, user shall set storage management as in Ch. 5.4. 4.1 Playback The playback interface is shown as in Figure 4-. Figure 4-1 There are four sections: ...

  • Page 26: Function Of Play

    4.1.1 Function of Play The function of play is shown as in Figure 4-2 and Figure 4-3. Figure 4-2 Figure 4-3 Parameter Function When you see this button, it means pause or not played record. Click on this ① Play button, switch to normal play status.

  • Page 27: Playback File

    4.1.2 Playback File In calendar, blue date represents data currently has video record or snapshot. See Figure 4-4. Figure 4-4 Parameter Function  Select “dav”, as video playback. File Type Select “jpg” as picture playback.  Data Source Default is SD card. Step 1.
  • Page 28 Figure 4-6 Parameter Function It means records within searched start time and end time on the date. Search Record Format There are two formats: dav, mp4.  Click the download button and download file to path in Ch. 5.1.2.5. Download ...

  • Page 29: Playback Cut

    Parameter Function Click on back button to go to calendar interface. Back 4.1.3 Playback Cut Note: Playback cut function will automatically pause playing record as playback cut and playback cannot be at the same time. Step 1. Click on start time to cut on time axis. This time must be within progress bar range. Step 2.

  • Page 30: Assistant Function

    Figure 4-9 Parameter Function Click on it, means video in past 24 hours. 24 hours Click on it, means video in past 2 hours. 2 hours Click on it, means video in past 1 hour. 1 hour Click on it, means video in past 30 min. 30 min 4.1.6 Assistant Function Video playback assistant function is shown in Figure 4-10.

  • Page 31: Play

    Figure 4-11 4.2.1 Play Figure 4-12 Default icon is and it means pause or not played picture. Click on play button to switch to normal play status. Icon become Click on it to pause. 4.2.2 Playback File...
  • Page 32 Figure 4-13 Step 1. Click on file list , select snapshot file of the date. Step 2. Double click on file in list, to play this snapshot. Parameter Function It means all snapshot files within the start time and end time of selected date. Search...

  • Page 33: Snapshot Type

    Parameter Function Click the download button to open snapshot file or directly download to local Download according to the browser types. Click on back button to return to calendar interface and re-select time. Back Figure 4-14 4.2.3 Snapshot Type...
  • Page 34 After checking snapshot file type, in file list only display file of selected type. Users can also select the snapshot type to be displayed via the dropdown box above the file list. See Figure 4-. Figure 4-15...

  • Page 35: Setup

    5 Setup Web client setup support camera, network, time, storage, system and system info view. 5.1 Camera The camera setting includes conditions, profile management, zoom and focus. 5.1.1 Conditions Note: The camera parameter may be different according to different models, please refer to the actual product for more details.
  • Page 36 Parameter Note It is to adjust the image overall brightness via linear adjustment mode. Brightness The larger the number is, the brighter the picture is, and on the contrary it is opposite. The picture get blurry easily when the value is set too big. It is to adjust the picture contrast.
  • Page 37 5.1.1.2 Exposure Step 1 Select “Setup > Camera > Conditions > Exposure”. The system will display the “Exposure” interface which is shown in Figure 5-2. Figure 5-2 Step 2 It is to set the exposure parameter, please refer to the following sheet for more details. Parameter Note ...
  • Page 38 Parameter Note It is the camera exposure mode. Note:  When “Anti-flicker” is “Outdor”, the “exposure mode” can be set as “gain priority” or “shutter priority” mode.  Different devices have different exposure modes; please refer to the actual interface. It includes the following options: ...
  • Page 39 Step 3 Click “Save” to complete the parameter config of camera exposure. 5.1.1.3 Backlight Backlight mode can be divided into BLC, WDR and HLS. BLC: it can avoid cucoloris phenomenon of the darker area in the backlight environment. WDR: It can suppress the overbright area and compensate darker area by enabling WDR, which can make the overall image clear.
  • Page 40  When selecting “Customized” mode, the system can realize exposure upon the selected area after it set customized area, which is to make the image of the selected area reach appropriate brightness.  When the “Mode” is set as “WDR”, it will lower the brightness of the area with high brightness and enhance the brightness of the area with low brightness, which is to make the objects in both high brightness and low brightness area display clearly.
  • Page 41  When the “Mode” is set as “Auto”, the system can auto compensate white balance upon different color temperatures, which is to make the image color normal.  When the “Mode” is set as “Natural”, the system can auto compensate white balance to the scene without artificial light, which is to make the image color normal.
  • Page 42 Step 2 Set day & night parameter; please refer to the following sheet for more details. Parameter Note It is to set the camera image displayed as color or black & white mode. Note: The setting of “Day/Night Mode” is not affected by the setting of “Profile Management”.
  • Page 43 Figure 5-6 Step 2 It is to set defog mode according to the actual scene.  When the “Mode” is set as “Manual”, it is to manually set intensity and air light mode, the system will adjust the image definition according to the intensity and air light mode which have been set previously.
  • Page 44 Figure 5-7 Step 2 It is to set IR light mode according to the actual scene.  When the “Mode” is set as “Manual”, it can manually set the brightness of IR light; the system will realize light compensation to the image according to the IR light intensity. ...
  • Page 45 Step 2 Set profile management.  When the “Profile Management” is set as “Normal”, the system will monitor according to the normal config. Figure 5-8  When the “Profile Management” is set as “Full Time”, you can select “Always Enable” in “Day” or “Night’, the system will monitor according to the config of “always enable”.

  • Page 46: Video

    5.1.1.9 Zoom and Focus Note: Only motorized vari-focal devices support focus and zoom function. Step 1 Select “Setup > Camera > Conditions > Zoom and Focus” and the system will display the interface of “Zoom and Focus” which is shown in Figure 5-11. Figure 5-11 Step 2 Adjust the focal length of the lens.
  • Page 47 5.1.2.1 Video Step 1 Select “Setup > Camera > Video > Video” and the system will display the interface of “Video” which is shown in Figure 5-12 or Figure 5-13. Figure 5-12 (Non fisheye) Figure 5-13 (Fisheye) Step 2...
  • Page 48 Set video bit stream, please refer to the following sheet for more details about the parameters. Parameter Function It will display the parameter when the device is fisheye. There are three installation modes for fisheye which are ceiling, wall mount and ground installation, please select installation mode according to the actual installation scene of the fisheye.
  • Page 49 Parameter Function Select “Enable” to enable sub stream. Sub Stream Enable The device supports enabling sub stream 1 and sub stream 2 at the same time. It can enhance image compression performance and Smart Codec reduce storage space by enabling intelligent encoding. Note: After intelligent encoding is enabled, the device will not support third stream, ROI or intelligent event detection,...
  • Page 50 Parameter Function  In CBR, the bit rate here is the max value. In Bit Rate dynamic video, system needs to low frame rate or video quality to guarantee the value.  The value is null in VBR mode.  Please refer to recommend bit rate for the detailed information.
  • Page 51 Figure 5-14 3. Select the needed resolution and clip the needed image on the interface, which is shown in Figure 5-15. 4. Click “Save”. You can check the clipped video in the preview interface (the sub stream 2 preview interface only displays the clipped area), which is shown in Figure 5-15.
  • Page 52 Figure 5-15 Step 3 Click “Save” to complete video stream setup. 5.1.2.2 Snapshot The snapshot interface is shown as in Figure 5-16. Figure 5-16 Please refer to the following sheet for detailed information.
  • Page 53 Parameter Function There are two modes: general (schedule) and Event (activation). Snapshot type Image size It is the same as the resolution of main stream. It is to set the image quality. There are six levels. Quality It is to set snapshot frequency. Optional1~7s/picture, customized. Interval 5.1.2.3 Video Overlay The video overlay interface is shown as in Figure 5-17.
  • Page 54 Figure 5-18 Figure 5-19...
  • Page 55 Figure 5-20 Figure 5-21...
  • Page 56 Figure 5-22 Please refer to the following sheet for detailed information. Parameter Function  Here you can privacy mask the specified video in the Privacy Masking monitor video.  System max supports 4 privacy mask zones.  You can enable this function so that system overlays time Time Title information in video window.
  • Page 57  Set privacy mask, channel title, time title, location, overlay Refresh and save the change. You can click on Refresh to see effect.  Click it to restore default config. Default  Click it to complete video settings. Save 5.1.2.4 ROI Note: Some series don’t support ROI setup function.

  • Page 58: Audio

    Figure 5-24 Parameters Note Check “Enable”, then it will display the ROI in the video monitoring window; Enable Check “Disable”, then it won’t display.  Set the image quality of ROI, ranging from 1～6, default is 6. Note: Image Quality For fisheye device, it ranges from 1~6 (best), default is 6 (best) Able to set area block, max 4 areas.
  • Page 59 Figure 5-26 Please refer to the following sheet for detailed information. Parameter Function Enable You can enable audio only when video is enabled. After selecting the “Enable” of main stream or sub stream, the network transmission stream is the audio/video composite stream, otherwise it only includes video image.
  • Page 60 AudioIn Type Two modes to select: LineIn, Mic. Device needs to connect external audio input source under LineIn mode, and it doesn’t need to connect external audio input source under Mic mode. Noise Filter Enable the function and it can filter relevant noise. Microphone Adjust microphone volume from 0～100.

  • Page 61: Network

    Step 1 Use the left mouse button to click the hollow circle in the “choice” column on the left, ，which means effective choice of alarm audio. and shows ，select “save target as” to download. Step 2 Use the right mouse button to click 5.2 Network 5.2.1 TCP/IP The TCP/IP interface is shown as in Figure 5-29.
  • Page 62 IP Version It is to select IP version. IPV4 or IPV6. You can access the IP address of these two versions. IP Address Please use the keyboard to input the corresponding number to modify the IP address and then set the corresponding subnet mask and the default gateway.

  • Page 63: Connection

    Figure 5-30 5.2.2 Connection Connection 5.2.2.1 The connection interface is shown as in Figure 5-31. Figure 5-31 Please refer to the following sheet for detailed information. Parameter Function It is the max Web connection for the same device. The value ranges from 1 connection to 20.
  • Page 64 UDP port Port range is 1025~65534. The default value is 37778. You can input the actual port number if necessary. HTTP port Port range is 1025~65524. The default value is 80. You can input the actual port number if necessary. ...

  • Page 65: Pppoe

    Figure 5-32 5.2.3 PPPoE The PPPoE interface is shown as in Figure 5-33. Enter the PPPoE username and password which are provided by ISP (Internet Service Provider), and click “Enable”. The network camera will automatically establish network connection in the mode of PPPoE after it is enabled, after it is successful, the IP of the “IP Address”...

  • Page 66: Ddns

    Figure 5-33 5.2.4 DDNS The DDNS interface is shown as in Figure 5-34. The DDNS is to set to connect the various servers so that you can access the system via the server. Please go to the corresponding service website to apply a domain name and then access the system via the domain.

  • Page 67: Ip Filter

    Parameter Function Username The user name you input to log in the server, optional. The ICDDNS interface is shown as in Figure 5-35. Figure 5-35 Parameter Function Server Type You can select ICDDNS protocol Server Address Under ICDDNS the default server address is “ www.icddns.com” Mode Default is auto, manual is optional.

  • Page 68: Smtp （E-Mail)

    Here you can add IP address and MAC address. You must add these addresses before enabling the trusted sites. Please note: You must set MAC address in the same network segment. Figure 5-36 5.2.6 SMTP （e-mail) The SMTP interface is shown as in Figure 5-37. Figure 5-37 Please refer to the following sheet for detailed information.

  • Page 69: Upnp

    Parameter Function Input server address and then enable this function. SMTP Server Port Default value is 25. You can modify it if necessary. Anonymity For the server which supports the anonymity email function, it won’t display the information of the sender. The user name of the sender email account.

  • Page 70: Snmp

    Enable UPnP from the Web. If your UPnP is enabled in the Windows OS, the network camera can auto detect it via the “My Network Places”. Under manual mode, you can modify external port. Under auto mode, select idle port for auto port mapping without user modification.
  • Page 71 Figure 5-39 Please refer to the following sheet for detailed information. Parameter Function  SNMP Version Check SNMP v1, device only process v1 info.  Check SNMP v2, device only process v2 info.  Check SNMP v3, can set username, password and encryption method.
  • Page 72 Figure 5-40 Check SNMP v3 version and SNMP port, read community, write community, Trap address, Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is SNMP v3, users need to configure parameter in chart. Parameter Function SNMP Version...

  • Page 73: Bonjour

    5.2.9 Bonjour The Bonjour interface is shown as below. See Figure 5-41. Bonjour is based on the multicast DNS service from the Apple. The Bonjour device can automatically broadcast its service information and listen to the service information from other device. You can use the browse of the Bonjour service in the same LAN to search the network camera device and then access if you do not know the network camera information such as IP address.
  • Page 74 Figure 5-42 Please refer to the following sheet for detailed information. Parameter Function Select to enable multicast function. Main stream and sub stream cannot be Enable used at the same time. Multicast address Main/sub stream multicast default address is 224.1.2.4 and its range is 224.0.0.0～239.255.255.255.
  • Page 75 Figure 4-53 Parameter Function Wireless Net Type Auto, WCDMA, FDD-LTE optional, you can select according to the operator. Enable Check to enable 4G module. It shall be acquired from the operator according to the setup of operator. Auto, PAP and CHAP, the authentication algorithm is Authentication Mode different according to different operators.

  • Page 76: Wifi

    5.2.11.2 Mobile Setting Figure 4-54 Please refer to the following sheet for detailed information. Parameter Function Message Send In the event, after the corresponding message activation is enabled, it will send message to the phone of receiver when event happens. It needs to enable the function of message activation function in the event interface when using the function.
  • Page 77 Figure 5-45 WIFI setting method is as follows: Step 1 ，means enabling WIFI function. Click , show as Step 2 Click “ Search SSID”, and shows the wireless network hot spot of the current network camera environment in the list. Figure 5-46...
  • Page 78 Step 3 Click “Add SSID” when need to add a wireless network manually，pop out an interface in the figure below, and enter network ID in the dialog box. Figure 5-47 Step 4 Double click on one can pop out the signal intensity and authentication of the hot spot. ·...

  • Page 79: Qos

    Figure 5-49 Please refer to the following sheet for detailed information. Parameter Function Authentication PEAP (protected EAP protocol). It needs the username to login, which is authenticated by the Username server. Password Please input password here. 5.2.14 QoS The QoS interface is shown as below. See Figure 5-50. Qos (Quality of Service) is network security mechanism.

  • Page 80: Https

    Figure 5-50 Please refer to the following sheet for detailed information. Parameter Function Real-time The value ranges from 0 to 63. The router or the switcher can monitor provide different service for various data packets. Command The value ranges from 0 to 63. The router or the switcher can provide different service for various data packets.
  • Page 81 Figure 5-51 2. Click “Create” and it will pop out the dialog box of “HTTPs”, which is shown in Figure 5-52. Figure 5-52 3. Fill in corresponding “Country”, “Province” and some other information, click “Create” after filling in. It will show the prompt of “Create Successfully”, which means the server certificate has been successfully created.
  • Page 82 Note: Make sure the “IP or domain name” is the same as that of the device. 4. Click “Install” and it will install the certificate on the device end, which is shown in Figure 5-53. Figure 5-53 5. Click “Download”. It will pop out the dialog box of “Save as”, save the file into the computer.
  • Page 83 Figure 5-54 6. Double click the downloaded icon of “RootCert.cer”. The system will display the information interface of “Certificate”, which is shown in Figure 5-55.
  • Page 84 Figure 5-55 7. Click “Install Certificate” and it will pop out the interface of “Certificate Import Wizard”, which is shown in Figure 5-56.
  • Page 85 Figure 5-56 8. Click “Next”. Select “Trusted Root Certification Authorities”, which is shown in Figure 5-57.
  • Page 86 Figure 5-57 9. Click “Next”. The system will display the interface of “Completing the Certificate Import Wizard”, which is shown in Figure 5-58.
  • Page 87 Figure 5-58 10. Click “Finish”, and it will pop out the dialog box of “Security Warning”, which is shown in Figure 5-59.
  • Page 88 Figure 5-59 11. Click “Yes”. It will pop out the dialog box of “Import Successful”, click “Ok” to complete downloading certificate, which is shown in Figure 5-60. Figure 5-60  Please refer to the following steps if you select “Install Signed Certificate”. 1.
  • Page 89 Figure 5-61 2. Select signed certificate and certificate key path respectively via “Browse”, click “Upload”. 3. Install root certificate, please refer to step 6~11 for more details. 4. Check “Enable HTTPs”, click “Save”. The system will display the dialog box of “Need to reboot the device”, and then the config is valid.

  • Page 90: Event

    Figure 5-63 Note: “xx.xx.xx.xx” is corresponding to your IP or domain name. 5.3 Event 5.3.1 Video detection 5.3.1.1 Motion Detection Step 1 Select “Setup > Event > Video Detection > Motion Detection’ and the system will display the interface of “Motion Detection”...
  • Page 91 Figure 5-64 Step 2 Select “Enable” to enable motion detection function. Step 3 Set motion detection area. 1. Click “Setup” and the system will pop out the interface of “Setting Area”, which is shown in Figure 5-...
  • Page 92 Figure 5-65 2. Set area name, it is to set valid area of motion detection according to the actual situation, and it can set the value of sensitivity and threshold respectively. The bigger the sensitivity is, the easier it is to generate motion detection, the smaller the threshold is, the easier it is to generate motion detection;...
  • Page 93 Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
  • Page 94 Parameter Function Check it and the flash will be on when alarm occurs, and the flash will Flash linkage be off until the end of alarm after corresponding delay.  Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm.
  • Page 95 Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
  • Page 96 Figure 5-67 Step 2 Check “Enable” to enable the function of scene changing. Step 3 It is to set the parameters of scene changing, please refer to the following sheet for more details. Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set.

  • Page 97: Audio Detection

    Parameter Function  Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm.  The event type includes: preset, tour and pattern. You need to check the box here so that system can backup motion detection Snapshot snapshot file.
  • Page 98 Parameter Function Sensitivity It can be judged as audio abnormity when the input volume change exceeds continuous environment volume; users need to adjust according to the actual environment test. Threshold It is to set the filtered environment volume intensity, if the environmental noise is too big, then the value needs to be set higher, users can adjust according to the actual environment test.

  • Page 99: Smart Plan

    5.3.3 Smart Plan Smart plan is the master switch for intelligent analysis such as “Face Detection”, “Heat Map”, “IVS”, “People Counting” and so on, the corresponding intelligent functions can be valid after smart plan is enabled. Step 1 Select “Setup > Event > Smart Plan”. The system will display the interface of “Smart Plan”, which is shown in Figure 5-69.
  • Page 100 5.3.4.1 IVS 5.3.4.1.1 Tripwire It will trigger alarm when the target crosses the warning line according to the movement direction which has been set. It needs some time from when the target appears to when the target is confirmed, so it has to leave some space on both sides of the warning line when setting the warning line, please do not set the warning line near the obstructions.
  • Page 101 Parameter Function Object tracking Select “Object tracking” to enable the function, refer to “2.4 Video Window Adjustment” for more details. Note: The function is only supported by some models. Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set.
  • Page 102  Cross means that it will trigger alarm when the target enters or exits the area.  Appears means that it will trigger alarm when the target appears in the area.  As for the report interval of the IVS function in the area, the system will trigger an alarm if it detects same event happened during the interval;...
  • Page 103 Parameter Function Object tracking Select “Object tracking” to enable the function, refer to “2.4 Video Window Adjustment” for more details. Note: The function is only supported by some models. Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set.
  • Page 104 5.3.4.3 Abandoned Object Abandoned object means the system will trigger alarm if the abandoned object in the monitoring scene exceeds the time which has been set by the users. Abandoned object and missing object can be confusing in a situation where both foreground and background are complicated.
  • Page 105 It is to set the parameter of abandoned object, please refer to the following sheet for more details. Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1.
  • Page 106 Application scene: it can be applied to the scene where the target is sparse and there is no obvious and frequent light change. False alarm will be increased in the scene where the target density is high and there is frequent obstruction; the false alarm will be increased in the scene where there are more people staying.

  • Page 107: Face Detection

    Parameter Function Note: Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
  • Page 108 Figure 5-74 Step 2 Select “Enable” to enable face detection function. Step 3 Click “Draw Target” to draw the size model of target filter in the video image. Step 4 It is to set the parameters of face detection, please refer to the following sheet for more details. Parameter Function Note:...

  • Page 109: People Counting

    Parameter Function Relay out Enable alarm activation function. You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs. System can delay the alarm output for specified time after alarm ended. Alarm Delay If you enabled this function, System can send out email to alert you when Send Email alarm occurs and ends.
  • Page 110 Click “Draw Target” to draw the size model of filtered target in the video image. Step 5 It is to set the parameters of entrance and exit, please refer to the following sheet for more details. Parameter Function Select “Enable OSD” and it will display the people number statistics of Enable OSD entrance and exit in the monitoring image.

  • Page 111: Heat Map

    It is to generate a form of report according to the number statistics. Step 1 Select “Setup > Event > People Counting > Report “and the system will display the interface of “Report’, which is shown in Figure 5-76. Figure 5-76 Step 2 It is to set search condition, please refer to the following sheet for more details.
  • Page 112 Select “Setup > Event > Heat Map > Heat Map” and the system will display the interface of “Heat Map”, which is shown in Figure 5-77. Figure 5-77 Step 2 Select “Enable” to enable heat map function. Step 3 It is to set the working period. 1.
  • Page 113 Figure 5-78 2. It is to set working period according to the following methods:  You can input time numerical value or press the left mouse button to drag on the setup interface to set.  There are six periods to be set every day, select the check box in front of the period, and then the period is valid.

  • Page 114: Alarm

    Figure 5-79 Step 2 It is to set begin time and end time. Step 3 Click “Search” to complete report statistics, click “Export” to export the statistics report. 5.3.8 Alarm Please note some series products do not support this function. 5.3.2.1 PIR alarm The alarm activation interface PIR alarm is shown as in figure 5-80.
  • Page 115 Figure 5-80 Please refer to the following sheet for detailed information. Parameter Function After enabled, relay activation will work. Check it and enable the Enable PIR alarm.  This function becomes activated in the specified periods. Working  There are six periods in one day. Please draw a circle to period enable corresponding period.
  • Page 116 Parameter Function Enable alarm activation function. You need to select alarm output Relay out port so that system can activate corresponding alarm device when alarm occurs. System can delay the alarm output for specified time after alarm Alarm delay ended. The value ranges from 10s to 300s. Send Email After this function is enabled, system can send out email to alert you when alarm occurs and ends.
  • Page 117 Parameter Function Check it and set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm. The event type includes: preset, tour and pattern and so on. 5.3.8.2 Flash Set Figure 5-82 Parameter Function ON/OFF ON means flash is on;...

  • Page 118: Abnormity

    Figure 5-83 parameter Function Enable Check it and enable audio detection. It will trigger alarm and set up a series of linkage when volume exceeds the set Threshold threshold. 5.3.9 Abnormity Abnormity includes No SD Card, Capacity Warning, SD Card Error, Disconnection, IP Conflict and Unauthorized Access.
  • Page 119 Figure 5-84 Figure 5-85...
  • Page 120 Figure 5-86 Please refer to the following sheet for detailed information. Parameter Function Check to alarm when SD card is abnormal. Enable Check to enable relay-out alarm. Relay-out Relay out The alarm output can delay for the specified time after alarm stops. The delay value ranges from 10s to 300s.

  • Page 121: Storage Management

    Figure 5-87 When login password keep been wrong for a few times, unauthorized access alarm occurs. This operation is similar to SD card error. Allow login error times as when it exceeds this limit, user account will be locked. Figure 5-88 5.4 Storage Management 5.4.1 Schedule...
  • Page 122 Figure 5-89 Step 2. From Monday to Sunday select record time, click on setup on the right, see Figure 5-90.  Set period according to actual need. There are six periods available each day.  By checking or unchecking, you can add or delete three types of record schedule: General, Motion, and Alarm.
  • Page 123 Figure 5-91 Step 4. In record schedule interface, click on OK. System prompts it is successfully saved. 5.4.1.2 Snapshot Schedule Snapshot setup as: Step 1. Click on Snapshot Schedule tab, see Figure 5-92. Figure 5-92 Step 2. From Monday to Sunday select snapshot time, click on setup on the right. See Figure 5-93. ...
  • Page 124  By checking or unchecking, user can add or delete three types of snapshot schedule: General, Motion and Alarm. Note: Period setup can be done by dragging in snapshot schedule interface while not releasing left mouse. Figure 5-93 Step 3. Click on OK, return to snapshot schedule interface. See Figure 5-94. ...

  • Page 125: Destination

    5.4.1.3 Holiday Schedule Holiday schedule can set specific date as holiday. Step 1. Click on Holiday Schedule tab, see Figure 5-95. Figure 5-95 Step 2. Select date to set as holiday. The selected date will be highlighted in yellow. Step 3. Check Record/Snapshot, click on Save. System prompts it is successfully saved. Step 4.
  • Page 126 Figure 5-96 Please refer to the following sheet for detailed information. Parameter Function Event It includes: scheduled, motion detect and alarm. Type Local It saved in the SD card. It saved in the FTP server. It saved in NAS disk. 5.4.2.2 Local The local interface is shown as in Figure 5-97.

  • Page 127: Record Control

    You need to check the box to enable the FTP function. When network disconnect occurred or there is malfunction. Emergency storage can save the record/snapshot picture to the local SD card. Click the test button to check if the FTP server can be connected for test. Figure 5-98 5.4.2.4 NAS You need to check the box to enable the NAS function.

  • Page 128: System

    The record control interface is shown as in Figure 5-100. Figure 5-100 Please refer to the following sheet for detailed information. Parameter Function Here you can select file size within 1min~120min. Default setup is 8 Pack minutes. Duration Pre-record Please input pre-record value here. For example, system can record the four seconds video in the buffer.
  • Page 129 Figure 5-101 Please refer to the following sheet for detailed information. Parameter Function It is to set device name. Device Note: Different devices have different names. Name Video This is to display video standard such as PAL. Standard Language You can select the language from the dropdown list. TV Out You can open or close the function, it can only be supported by the devices with TV Out.
  • Page 130 Figure 5-102 Please refer to the following sheet for detailed information. Parameter Function Here you can select date format from the dropdown list. Date format There are two options: 24-H and 12-H. Time Format The time zone of the device. Time zone It is to set system time.

  • Page 131: Account

    5.5.2 Account  For user name and user group, the max length is 31 characters, which can be made up of digit, letter, underline, hyphen, dot and @.  Password can be 0~32 characters in number and letter only. User can modify other user’s password.
  • Page 132 Figure 5-104 Modify user It is to modify the user property, belonging group, password and rights. See Figure 5-105. Modify password It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup.
  • Page 133 Figure 5-105 5.5.2.2 Group The group management interface can add/remove group, modify group password and etc. The interface is shown as in Figure 5-106. Figure 5-106 Add group: It is to add group and set its corresponding rights. See Figure 5-107.

  • Page 134: Ptz

    Please input the group name and then check the box to select the corresponding rights. It includes: preview, playback, record control, PTZ control and etc. Figure 5-107 Modify group Click the modify group button, you can see an interface is shown as in Figure 5-108. Here you can modify group information such as remarks and rights.

  • Page 135: Default

    The PTZ settings interface is shown as in Figure 5-91. Figure 5-109 Please refer to the following sheet for detailed information. Parameter Function Select the corresponding dome protocol. Protocol Set corresponding dome address. Default value is 1. Address Please note your setup here shall comply with your dome address; otherwise you cannot control the speed dome.

  • Page 136: Import/Export

    Figure 5-110 5.5.5 Import/Export The interface is shown as in Figure 5-111. Figure 5-111 Please refer to the following sheet for detailed information. Parameter Function It is to import the local setup files to the system. Import It is to export the corresponding system setup to your local PC. Export 5.5.6 Remote control Note:...

  • Page 137: Auto Maintenance

    Figure 5-112 Parameter Function Learn Bind remote control or wireless alarm with equipment. Clear Unbind remote control with equipment. Start arm after the time you choose, disarm comes into effect immediately. Note: Arm/Disarm With disarm status, all the following alarms won’t trigger: motion detect alarm, masking alarm, local alarm, PIR alarm, wireless alarm.

  • Page 138: Upgrade

    Parameter Function Auto Reboot Check it and set auto reboot time. Auto Delete Old Check it and set period within 1~31 days. Files 5.5.7 Upgrade The upgrade interface is shown as in Figure 5-114. Please select the upgrade file (file extension is “.bin”) and then click the update button to begin firmware update.

  • Page 139: Log

    5.6.2 Log Here you can view system log. See Figure 5-116. Figure 5-116 Please refer to the following sheet for log parameter information. Parameter Function Set the start time of the requested log. (The earliest time is 2000/1/1) Start time Set the end time of the requested log.
  • Page 140 Figure 5-117...

  • Page 141: Alarm

    6 Alarm Please note some series product does not support this function. Click alarm function, you can see an interface is shown as in Figure 6-1. Here you can set device alarm type and alarm sound setup. Figure 6-1 Please refer to the following sheet for detailed information. Type Parameter Function...
  • Page 142 Type Parameter Function Operation Prompt When alarm is triggered, there will be s inmain menu of alarm interface and system automatically records alarm info. The icon disappears when user click on alarm menu bar. Note: If alarm interface is displayed, when alarm is triggered, there will be no image prompt, but alarm record will be in list on the right.

  • Page 143: Log Out

    7 Log out Click log out button, system goes back to log in interface. See Figure 7-1. Figure 7-1 Note:  This manual is for reference only. Slight difference may be found in user interface.  All the designs and software here are subject to change without prior written notice. ...

Table of Contents