Related Manuals for ClearView IP-PT-885
Summary of Contents for ClearView IP-PT-885
- Page 1 IP-PT-885 3-inch 2 Megapixel Intelligent Network Speed Dome Installation Manual Version 1.0.0...
-
Page 2: Table Of Contents
Table of Contents INTELLIGENT SPEED DOME INSTALLATION PREPARATION ....... 1 Basic Requirement ..........................1 Check installation space and installation location intension ............1 Please keep all package material well for future use ............... 1 SETUP BEFORE INSTALLATION ..............2 Check Accessories ..........................2 Open Device............................ - Page 3 Installation............................... 7 4.2.1 Installation Requirements ........................ 7 4.2.2 Installation Steps..........................7 APPENDIX Ⅰ 24V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET ..................10 APPENDIX Ⅱ 12V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET ..................11 APPENDIX III WIRE GAUGE REFERENCE SHEET ..........12...
- Page 4 Welcome Thank you for purchasing our speed dome! Please read the following safeguards and warnings carefully before you install or use the product!
-
Page 5: Important Safeguards And Warnings
Important Safeguards and Warnings Safety Measures 1. Qualified Engineer Needed The installation engineer or maintenance engineer shall have corresponding CCTV system installation certificate or maintenance qualification certificate. The installation engineer or maintenance engineer shall have qualification certificate for work at height. - Page 6 All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair. Note Safety Transportation Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
- Page 7 Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result in shell transfiguration or paint flake. Do not allow the plastic or rubber material to touch the shell for a long time. It may result in paint flake.
-
Page 8: Intelligent Speed Dome Installation Preparation
1 INTELLIGENT SPEED DOME INSTALLATION PREPARATION 1.1 Basic Requirement All installation and operation here should conform to your local electrical safety codes. Before installation, please open the package and check all the components are included. Please make sure the speed dome installation environment and installation mode can meet your requirement. -
Page 9: Setup Before Installation
2 SETUP BEFORE INSTALLATION 2.1 Check Accessories Before the installation, please check the accessories one by one according to the packing list. Please make sure all the components listed are included. 2.2 Open Device Remove the package and then take out the device. Open the transparent cover and take out the packing material around the speed dome driver. -
Page 10: Tf Card Slot And Reset Button
Figure 2-2 2.4 TF Card Slot and Reset Button TF card slot and RESET button is shown as in Figure 2-3. Press the RESET button for at least five seconds; you can restore factory default setup. Before you remove the SD card, please make sure it is not in read/write status; otherwise you may lose data or result in SD card damage. -
Page 11: Ceiling Installation
3 CEILING INSTALLATION 3.1 Installation Components The ceiling installation dome body is shown as in Figure 3-1. Figure 3-1 3.2 Ceiling Installation Steps 3.2.1 Installation Requirements The ceiling mount speed dome can be installed in the hard construction wall in the indoor environments. -
Page 12: Cable Connection
Figure 3-2 Figure 3-3 3.2.3 Cable Connection The step listed below is for ceiling or wall mount series product. - Page 13 Please refer to Figure 3-4 to connect the power cable, network cable, audio cable, alarm input/output pin of the intelligent speed dome composite cable according to your actual requirements. Please use insulation tape to seal the cable connection ports to do proper waterproof work.
-
Page 14: Wall Mount Bracket Installation
4 WALL MOUNT BRACKET INSTALLATION 4.1 Component Installation Wall mount bracket is shown as below. See Figure 4-1. Figure 4-1 4.2 Installation 4.2.1 Installation Requirements The wall mount speed dome can be installed in the hard construction wall in the indoor environments. - Page 15 Figure 4-2 2). Connect the adapter block to the internal thread of the wall mount bracket. Pull the intelligent speed dome composite cable through the adapter block and end of the column of the wall-mount bracket and pull it out of the other end of the wall mount bracket. Line up the pedestal to the internal hole of the adapter block.
- Page 16 Figure 4-4...
-
Page 17: Appendix Ⅰ 24V Ac Wire Gauge And Transmission Distance
5 APPENDIX Ⅰ 24V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET The recommended max transmission distance is under the following environments: The wire diameter is fixed and the DC 24V power voltage loss rate is below 10%. For the device of DC power supplying, the max allowed voltage loss rate is 10%. -
Page 18: Appendix Ⅱ 12V Ac Wire Gauge And Transmission Distance
6 APPENDIX Ⅱ 12V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET The recommended max transmission distance is under the following environments: The wire diameter is fixed and the DC 12V power voltage loss rate is below 10%. For the device of DC power supplying, the max allowed voltage loss rate is 10%. -
Page 19: Appendix Iii Wire Gauge Reference Sheet
7 APPENDIX III WIRE GAUGE REFERENCE SHEET Metric bare wire Bare wire cross diameter section （mm） （mm ） 0.050 0.00196 0.060 0.00283 0.070 0.00385 0.080 0.00503 0.090 0.00636 0.100 0.00785 0.110 0.00950 0.130 0.01327 0.140 0.01539 0.160 0.02011 0.180 0.02545 0.200 0.03142 0.230...
Need help?
Do you have a question about the IP-PT-885 and is the answer not in the manual?
Questions and answers