Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Heatmiser PRT-EWTS
Summary of Contents for Heatmiser PRT-EWTS
- Page 1 Model: PRT-EWTS Model: PRT-EWTS...
-
Page 2: Table Of Contents
Model: PRT-EWTS Table Of Contents Temperature Hold Product Image Holiday Programming Table of Contents Frost Protection What is a Programmable Room Thermostat? Heating ON/OFF Installation Procedure Optional Features Explained 21-22 LCD Display Adjusting the Optional Settings Pairing the Thermostat Optional Settings - Features Table... -
Page 3: Model: Prt-Ewts
Similarly reducing the temperature setting does not affect how quickly the room cools properly. down. Setting a programmable room thermostat to a lower temperature will result in the room being controlled at a lower temperature, and saves energy. Wireless Series Model: PRT-EWTS... -
Page 4: Installation Procedure
Wall Mounting: Step 1 Fix the wall plate to the wall. Step 2 Push the thermostat onto the wall plate. Desk Stand: Step A Remove the thermostat from the wall plate. Step B Release the desk stand. Wireless Series Model: PRT-EWTS... -
Page 5: Lcd Display
View Floor Temperature Key - Used to change display to show floor temperature. Current Temp - Indicates the current sensor temperature. Units of Temperature - Degrees Celsius or Fahrenheit. Comfort Level Selection Keys - Used in comfort level setup (see page 13-14). Wireless Series Model: PRT-EWTS... -
Page 6: Pairing The Thermostat
RF devices. • Use the Up/Down keys to enter the address ............• Press SETUP to Pair the thermostat and receiver ............Note: You must finish pairing the thermostat before the communication LED goes out. Comms LED Wireless Series Model: PRT-EWTS... -
Page 7: Setting The Clock
When the thermostat is in air and floor sensing mode, the thermostat will display a FLOOR button. Pressing this allows you to view the current floor temperature, the thermostat automatically reverts back to ROOM TEMP after 5 seconds. Wireless Series Model: PRT-EWTS... -
Page 8: Comfort Levels Explained
09:00 21°C “Sat Sun” prompting you to program the display Tue. Leave 22:00 16°C temperature levels for the weekend. Return --,-- --°C Sleep --,-- --°C • When complete, press DONE to confirm settings and exit .... Wireless Series Model: PRT-EWTS... -
Page 9: Clean Screen
At this time, the thermostat will revert back to the programmed levels. • When activated, you will see the Keypad Lock symbol. • To cancel, press the bottom right corner of the display again for 10 secs. Keypad Lock Indicator Set Temperature Set Icon Wireless Series Model: PRT-EWTS... -
Page 10: Temperature Hold
Hold Temperature the programmed schedule at 00:00 on Monday. To cancel a Holiday setting, reduce the holiday time to 00 days. To cancel a temperature hold, follow the same steps but reduce the time to 00:00. Wireless Series Model: PRT-EWTS... -
Page 11: Frost Protection
The display and heating output will be turned off completely. To cancel the frost protect mode, press the key once. To turn the thermostat back on, press the Power key once ........Thermostat completely OFF Thermostat powered ON Frost Protection Mode Enabled Wireless Series Model: PRT-EWTS... -
Page 12: Optional Features Explained
Should the RF link fail, the receiver will limit the floor from overheating. The limit can be adjusted from 20-45 Wireless Series Model: PRT-EWTS... -
Page 13: Adjusting The Optional Settings
Floor Limit - 45 C (28 C = Default) number (shown on page 24) and then use the Up/Down keys in the center to adjust the setting ..................• Press DONE to confirm settings and exit ............Wireless Series Model: PRT-EWTS... -
Page 14: Re-Calibrating The Thermostat
Press the Power key once to turn the thermostat back on ........• Press the Power key once to turn the thermostat display back on ...... All icons displayed simultaneously. Factory reset is complete. Calibration Temperature Setting Set Icon Wireless Series Model: PRT-EWTS... -
Page 15: Battery Recharging
To recharge the battery you need to connect the thermostat to a power source. A mini USB to USB lead is supplied with the thermostat so you can recharge from the USB port on your laptop or PC. Part ref: USB-02 Wireless Series Model: PRT-EWTS... -
Page 16: Error Codes
E4 = The floor sensing probe to the RC2-WTS has either not been connected, has been wired incorrectly or the probe is faulty............................................................................................................................................................................................................Error Number ..........................................................................................................................................................................Wireless Series Model: PRT-EWTS... - Page 17 Heating Professionals: Request a copy of our product installation guide containing detailed technical specifications for our complete product range: www.heatmiser.com/guide Want More Information? Call our support team on: +44 (0)1254 669090 Or view technical specifications directly on our website: www.heatmiser.com Twitter: heatmiseruk Facebook: facebook.com/thermostats...
Need help?
Do you have a question about the PRT-EWTS and is the answer not in the manual?
Questions and answers