Advertisement
2. Press the battery recondition button. The LCD
screen will display the following:
The battery recondition indicator, the clamp
icons and the battery icon will light solid; and the
battery reconditioning icons will flash.
3. To stop the reconditioning process, press the
battery recondition button again. Pressing any
other button during this process will have no
effect.
IMPORTANT: If 5 cycles of reconditioning does not
improve battery performance, discontinue and recycle
the battery. The battery charger will go into charging
mode after 24 hours automatically.
When disconnecting the charger, disconnect mains
cord, remove clamp from vehicle chassis, and then
remove clamp from battery terminal.
Using the Engine Start Function
1. Set up the battery charger and connect to
the battery following steps 1 through 2 in the
"Charging the Battery" section.
2. Press the engine start button. The LCD screen will
display the following:
The digital display shows the countdown.* The
battery charge gauge will indicate the battery's
current charge status. The engine start icon,
clamp icons and battery icon light solid, and the
arrow icons will gradually and repeatedly move
downward to the battery icon.
*The countdown will commence from "90" to
"00".
3. When "00" is reached, a beep will sound, the
battery icon will light solid and the engine start
icon (
) will begin flashing. The vehicle is ready
to start.
4. Crank the engine using manufacturer's guidelines,
typically in 3 to 5 second bursts. The digital
display shows "5 sec." indicating a 5-second
countdown, the gauge and all other indicators
disappear.
5. After cranking, the unit will automatically adjust
the charging current to 2A for 5 minutes and then
BC20BDAU_Manual_091216.indd 10-11
revert to charging mode. To stop charging, press
the charge button again.
IMPORTANT: The function requires a resting/cooling
period between attempts. Wait 4 to 5 minutes before a
second attempt at starting the engine, if needed.
When disconnecting the charger, disconnect mains
cord, remove clamp from vehicle chassis, and then
remove clamp from battery terminal.
TROUBLESHOOTING
Problem
Solution
The battery is
• Check that the battery charger
not charging
is properly connected to a live
mains socket.
• Make sure the output
connections are secured and
the polarity connection is
correct.
• If the voltage of the battery to
be charged has fallen below
2 volts, the battery cannot
be charged with this battery
charger.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance or
cleaning of the tool, unplug the unit from the power
supply.
• From time to time wipe the appliance with a damp
cloth. Do not use any abrasive or solvent-based
cleaner. Do not immerse the appliance in water.
Storage
• Store the unit in a clean, dry, cool place when not
in use.
• To maintain the operating condition and maximize
the life of the charger cords, always coil them loosely
for storage. Do not wrap them around the unit or
crimp them with a tight band.
PROTECTING THE ENVIRONMENT
Correct disposal of this product
This marking indicates that this product
should not be disposed with other
household waste. To prevent possible
harm to the environment or human health
from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of
material resources. To return your used device, please
use the return and collection systems or contact the
10
retailer where the product was purchased. They can
take this product for environmentally safe recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.
TECHNICAL DATA
Input:
230-240V ac, 50Hz, 2A
Output:
12V dc, 20A
Engine Start:
40A (5 seconds on; 5
minutes off)
WARRANTY
Our goods come with guarantees that cannot be
excluded under the Australian & New Zealand
Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation
for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of
acceptable quality and the failure does not
amount to a major failure.
Baccus Worldwide LLC is confident of the quality of
its products and offers an outstanding warranty. This
warranty statement is in addition to and in no way
prejudices your statutory rights under the Australian &
New Zealand Consumer Law.
If a Baccus Worldwide LLC product becomes
defective due to faulty materials, workmanship or
lack of conformity, within 24 months from the date
of purchase, Baccus Worldwide LLC guarantees to
replace defective parts, repair products subjected to
fair wear and tear or replace such products to make
sure of the minimum inconvenience to the customer
unless:
• The product has been used for trade, professional or
hire purposes;
• The product has been subjected to misuse or
neglect;
• The product has sustained damage through foreign
objects, substances or accidents;
• Repairs have been attempted by persons other than
Baccus Worldwide LLC service staff.
To claim on this warranty, you will need to submit
proof of purchase and return the allegedly defective
product to Baccus Worldwide LLC's local market
distributor, at your expense.
Please visit our website www.baccusworldwide.com
to register your new Baccus Worldwide LLC product
and to be kept up to date on new products and special
offers. Further information on the Baccus Worldwide
LLC brand and our range of products is available at
www.baccusworldwide.com.
Distributed by: Directed Electronics
Address: 44 Translink Drive, Keilor Park Victoria Australia 3042
PH: + 61 03 8331 4800 Email: service@directed.com.au
Baccus Worldwide LLC
Weena 290, 3012 NJ Rotterdam or
Postbus 819, 3000 AV Rotterdam
+31(0)10 282 16 11
11
9/12/2016 11:45:37 AM
Advertisement
