ADJ Encore Profile 1000 WW User Instructions page 5

Encore Profile 1000 WW
• "CHAN: 02" is 2 Channel DMX Mode.
• "CHAN: 03" is 3 Channel DMX Mode.
4. Please see page 15 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
Fade Mode:
1. Plug the fixture in and press the MODE button until "FADE RUN
SPEED:XX" is displayed. "XX" represents a number between
01-16.
2. Use the UP and DOWN buttons to find your desired color fade
mode.
3. Press the SET UP button and "SPEED:XX" will be displayed. Use
the UP and DOWN buttons to adjust the speed of the color
fade.
System Reset:
This will return the fixture to its factory settings.
1. Plug the fixture in and press the MODE button until "OTHER
MODE" is displayed.
2. Press the SET UP button until "SYSRESET" is displayed.
3. Press the UP and DOWN buttons simultaneously to reset or press
the MODE button to exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See
page 29 for the different dimming curves.
1. Plug the fixture in and press the MODE button until "DMX MODE
ADDR:XXX" is displayed.
2. Press the SET UP button until "DELAY:X" is displayed. "X" repre-
sents the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select
your desired dimming curve.
ADJ Products, LLC - www.adj.com - Encore Profile 1000 WW User Manual Page 8
Operating Instructions Encore Profile 1000 WW
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the fixture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to
when power is applied.
1. Plug the fixture in and press the MODE button until "DMX MODE
ADDR:XXX" is displayed.
2. Press the SET UP button until "DMX MODE NO" is displayed. The
current DMX state will be displayed.
• "BLACK" (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• "HOLD" (Last State) - If the DMX signal is lost or interrupted,
the fixture will stay in the last DMX set up.
• "AUTO" (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Press the UP or DOWN buttons to scroll through and select
your desired DMX state.
IR Receiver On/Off:
This function is used to activate and deactivate the infared sensor.
When this function is activated you can control the fixture using the
ADJ LED RC2 (sold separately), ADJ UC IR (sold separately), and
Airstream IR app. Please see pages 12-14 for remote controls and
functions. To control the Encore Profile 1000 WW, plug the included
IR receiver into IR receiver input located on the rear of the controller.
You must aim the remote at the IR sensor and be no more the 30 feet
away.
1. Plug the fixture in and press the MODE button until "OTHER
MODE" is displayed.
2. Press the SET UP button until "IR: XX" is displayed.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
Gamma:
This feature is predominately used when shooting video. Adjust the
gamma setting to clean up any lines that might be seen on camera.
1. Plug the fixture in and press the MODE button until "GAMMA" is
ADJ Products, LLC - www.adj.com - Encore Profile 1000 WW User Manual Page 9
Operating Instructions