Installation; Switching On The Appliance; Selecting The Temperature - Bosch KAN56 Operating And Installation Instructions

Installation

Installation location
Install the appliance in a dry, well
ventilated room. If installation near
a heat source is unavoidable, use
a suitable insulating plate or observe
the following minimum distances to
a heat source:
Observe the following minimum
distances to heat sources:
- 3 cm to an electric cooker.
- from an oil or solid fuel cooker
30 cm.
The floor on which the appliance is to
be installed must be rigid. If required,
reinforce the floor.
The appliance is very heavy, for empty
weight see the following table.
Basic model
Basic model
Model with dispenser
Model with home bar
Model with home bar
Model with dispenser&home bar
To ensure that the ice maker functions
correctly, the appliance must be
upright. To ensure that the doors
can open all the way, observe lateral
minimum distances when installing
the appliance in a corner or recess
(see section on Appliance
dimensions").
Installing and connecting
the appliance
Have a technician install the
appliance and connect it to the
water supply according to the
enclosed installation instructions.
After installing the appliance, wait at
least ½ hour before switching on the
appliance. During transportation the oil
in the compressor may have flowed
into the refrigeration system.
Before switching on the appliance for
the first time, clean the interior of the
appliance (see Cleaning the
appliance").
Electrical connection
Do not use any extension cables or
distributors. Two permanently installed
sockets are required for connection of
this appliance.
The socket for connection of the
appliance must be freely accessible.
Connect the appliance to 220 240 V/
50 Hz alternating current via a correctly
installed earthed socket. The socket
must be fused with a 10 A fuse or
higher.
If the appliance is to be operated in
a non European country, check on
Non - China
the rating plate whether the indica
ted voltage and current type corres
pond to the values of your mains
supply. The rating plate is situated
in the bottom left hand side of the
appliance. The power cord may be
replaced by an electrician only.
Warning!
!
Never connect the appliance to
104 kg electronic energy saver plugs
104Kg
(e.g. Ecoboy: Sava Plug) or to
113 kg
106Kg
power inverters which convert the
115 kg direct current to 230 V alternating
115Kg
current (e.g. solar equipment,
power supplies on ships).
Observe ambient
temperature and
ventilation
The climatic class can be found on the
rating plate and indicates the ambient
temperatures at which the appliance
can be operated.
Climatic class
SN
N
ST
T
Ventilation
Never cover the ventilation openings
in the base panel. Otherwise, the
refrigerating unit must work harder and
the power consumption is increased.
Switching on
the appliance
S Insert the mains plug into a socket.
The appliance begins to cool down as
soon as it is connected to the power
supply. When the doors are open,
the interior lights come on.
Note:
The preset temperatures (factory
settings) are reached after approx.
2 to 3 hours. Do not put any food in
the appliance beforehand.
To change the set temperatures >
see Setting the temperature".
Selecting the
temperature
Appliances with control
panel
- The temperature for the refrigerator
- The factory setting for the refrigerator
- The factory setting for the freezer
To change the values:
S Keep pressing the Selection button
Permitted ambient
temperature
+10 °C to 32 °C
+16 °C to 32 °C
+18 °C to 38 °C
+18 °C to 43 °C
The value last indicated is saved by the
system.
and freezer compartments can be
adjusted separately. The set value is
indicated on the display panel.
compartment is 4 °C.
compartment is 19 °C.
until the required temperature value
is indicated.
en
6