vita Vacumat 6000 M Operating Manual

vita Vacumat 6000 M Operating Manual

Heating system for dental ceramic furnace
Hide thumbs Also See for Vacumat 6000 M:

Advertisement

VITA VACUMAT
6000 M
®
Operating manual
VITA Farbkommunikation
VITA Farbkommunikation
VITA shade taking
VITA shade communication
VITA shade reproduction
VITA shade control
Date of issue: 10.13
VITA shade, VITA made.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vacumat 6000 M and is the answer not in the manual?

Questions and answers

Мария
July 21, 2025

Здравствуйте! В какой сервисный центр в Санкт-Петербурге можно обратиться? Не работает планшет.

Summary of Contents for vita Vacumat 6000 M

  • Page 1 VITA VACUMAT 6000 M ® Operating manual VITA Farbkommunikation VITA Farbkommunikation VITA shade taking VITA shade communication VITA shade reproduction VITA shade control Date of issue: 10.13 VITA shade, VITA made.
  • Page 2: Table Of Contents

    1 Introduction 2 Delivery Scope 2.1 Control unit 2.2 Accessories (can be purchased separately) 3 Technical Information 3.1 General description of the VITA VACUMAT 6000 M furnace 4 Technical data 4.1 Dimensions/Weights 4.1.1 VITA VACUMAT 6000 M furnace 4.2 Electrical specifications 4.2.1 Furnace...
  • Page 3: Introduction

    (maintenance, inspection, repairs), either with or on the device. We hope that you will find using VITA VACUMAT 6000 M to be an enjoyable and successful experience. Copyright The confidentiality of this operating manual must be maintained.
  • Page 4: Delivery Scope

    VACUMAT 6000 M / MP or VITA ZYRCOMAT 6000 MS. An additional switchbox and a connection cable are required for the operation of 2 or more VITA VACUMAT 6000 M / 6000 MP or VITA ZYRCOMAT 6000 MS with a VITA vPad comfort, VITA vPad excellence or VITA vPad clinical control unit.
  • Page 5: Technical Information

    VITA VACUMAT 6000 M Technical information General description of the VITA VACUMAT 6000 M furnace • High-performance technology with highest temperature accuracy for optimal firing results • Time-saving operating convenience, modest spatial requirements • Sheet steel casing with a painted or stainless-steel finish •...
  • Page 6: Intended Use

    VITA VACUMAT 6000 M 5 Intended use Basic information on the device construction The device is constructed according to a state of the art design and recognized safety regulations. However, if it is used inappropriately, hazards for the health and safety of the user or third parties may arise as well as the risk of damaging the device and other valuable assets.
  • Page 7: Ambient Conditions

    VITA VACUMAT 6000 M 7 Ambient conditions • Indoor use • Ambient temperature: 2°C to 40°C • Relative humidity: 80% at 31°C • Maximum altitude: 3,800 m • Rated voltage fluctuations must not exceed plus/minus 10% of the rated voltage...
  • Page 8: Installation And First Use

    VITA VACUMAT 6000 M 9 Installation and first use 9.1 Installation location • Install the device in a dry, heated room. The distance to the closest wall should be at least 25 cm. (see sect. 7. Ambient conditions) • When the temperature is below 15°C (59ºF) (e.g. after transport), leave the device to stand for approx.
  • Page 9: Status Display

    VITA VACUMAT 6000 M 9.3 Status display The status display indicates following operation status: • green – furnace in standby-mode • blue – firing program active • red – error Please see operating manual of the corresponding control unit. 9.4 Fuses On the back of the device (see sect.
  • Page 10: Connecting The Device To The Mains Power Supply

    VITA VACUMAT 6000 M 9.6 Connecting the device to the mains power supply Important! Before first use, read section 6 on safety information! For information about the connections, see sect. 9.2 • Attach the connection cable to the control unit and the furnace.
  • Page 11: Cleaning The Furnace

    VITA VACUMAT 6000 M 10 Cleaning the furnace Before each cleaning operation, remove the power supply plug! It is not necessary to clean the inside of the firing chamber. Cleaning the casing of the firing chamber at regular intervals with a damp cloth contributes to its operating safety.
  • Page 12: Mains Power Supply Failure

    The warranty and liability comply with the terms and conditions set in the contract. In the event of software modifications without the knowledge and approval of VITA Zahnfabrik H. Rauter GmbH & Co. KG, all liability and warranty claims are invalidated. 14.1 Spare parts Spare parts must comply with the technical requirements determined by the manufacturer.
  • Page 13: Alphabetical Order Of Contents

    VITA VACUMAT 6000 M Accessories Safety features Ambient conditions Safety instructions Authorized modes of operation Service Spare parts Status display CE mark Storage plates Cleaning work Switching off the device Connecting the device to the mains power supply Copyright Technical data...
  • Page 14 Claims for damages based on fault liability (culpa in contrahendo, breach of contract, unlawful acts, etc.) can only be made in the case of intent or gross negligence. The VITA Modulbox is not necessarily a component of the product.

Table of Contents