Download Print this page
Fein ASsd 636-1 Operating Instructions
Fein ASsd 636-1 Operating Instructions

Fein ASsd 636-1 Operating Instructions

42 volts

Advertisement

Quick Links

ASsd 636-1
To be handed to the workshop
Operating instructions
for the Electric Screw-Driver type ASsd 636-1
and for type ASsd 736-1 (42 Volts)
1. Technical data
Current:
~
(single phase AC)
for iron screws
Tool holder
Input
Type
up to
Speed R.P.M.
Watts
mm
Net
weight
in.
I
mm
full
load
ASsd 636-1
ASsd
736-1
,,4
6
450
2. Construction
This
screwdriver
is
an electric
tool
of
class II
with
protective
insulation
without earth
wire
and
is in
accordance with
the
VDE
regulations
0740. The protective insulation is
attained
by
the shockproof motor housing
made of Polyamide-and by insulat-
ing the
armature against the pinion.
The
protective insulation
is
tested
with
the
prescribed test voltage of 4000
V.
The machine
is radio suppressed in accordance with radio interference VDE
0875. It is supplied with a two-core
cable
without earth
wire and
must not be
earthed.
Type
ASsd 736-1
for low tension (42 Volts)
is of the same
design,
but without
protective
insulation.
The
machine
is provided
with
a
reversing switch for clockwise
and anticlockwise rotation.
It
must not be operated
when
the
machine is
running.
To prevent the overbridging of the insulation no additional
marking plates and signs must be riveted or screwed on the
housing. We
recommend
the use
of transfers
only.
3. Connection
Main
voltage
must
correspond to
the
operating voltage marked
I
no
load
lbs
I
kg
70
800
230
with
round
5.1
2.3
receiver
table below) by simply exchanging the pressure spring (70). For
exchanging
the pressure spring
only
unscrew the three
screws
(71) and draw off
guide
bushing.
First relieve the
stress ·of
the
adjusting
ring (68)! By turning
the adjusting ring
(68) the
required
torque is
adjusted by
means
of
the
pressure
spring
(70)
infinitely variable within a range of
torque.
I
Torque
I
I
Wire dia.
I
Spring
I
kpm
ft. lbs
mm
in.
0.30-0.70
2.2
-5.0
FD
1-186
(stand.)
4
5
h2
0.15-0.30
1.1
-2.2
FD
1-187
3.2
1
/a
0.10-0.20
0.75-1.5
FD 1-190
2.5
3
h2
The
screwdriver
is
provided with an instant release clutch, so
that the tool shaft is
separated
from the motor
when
reaching
the torque.
When
removing the machine
from
the
tightened
screw
the
clutch engages automatically.
Tightened
screws can
be
un-
screwed without adjusting
the
reversing ring (68).
on the rating plate.
The
tool
can
be plugged into plain or safety
5. Maintenance
sockets.
Switch must be in the "Off" position when
connecting.
4. Adjustment of
the•
torque
The
screwdriver
can
be adjusted for
three
ranges of
torque
(see
BE
223/e
X
1.73
Printed
in Germany
Before carrying out any maintenance work always remember
to pull out the plug.
Every 300
duty
hours blow
or brush out
the tool with
special
attention
to
carbon brush
holders and
insulated parts
in
order
to
guarantee the safety given by the protective
insulation.

Advertisement

loading
Need help?

Need help?

Do you have a question about the ASsd 636-1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

This manual is also suitable for:

Assd 736-1