Subscribe to Our Youtube Channel
Related Manuals for King Industrial KC-108-OSC
Summary of Contents for King Industrial KC-108-OSC
- Page 1 6” x 108” OSCILLATING edGe SANder 04/2017 INSTrUCTION MANUAL MOdeL: KC-108-OSC COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
-
Page 2: Warranty Information
WArrANTY INFOrMATION 2-YeAr KING CANAdA TOOLS LIMITed WArrANTY OFFerS A 2-YeAr LIMITed WArrANTY FOr THIS OSCILLATING edGe SANder FOr COMMerCIAL USe. PrOOF OF PUrCHASe Please keep your dated proof of purchase for warranty and servicing purposes. rePLACeMeNT PArTS Replacement parts for this product are available at our authorized King Canada service centres across Canada. LIMITed TOOL WArrANTY King Canada makes every effort to ensure that this product meets high quality and durability standards. -
Page 3: General Safety Instructions
GeNerAL SAFeTY INSTrUCTIONS VOLTAGe WArNING: Before connecting the machine to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate. A power source with voltage greater than specified can result in SERIOUS INJURY to the user - as well as damage the machine. -
Page 4: Electrical Information
eLeCTrICAL INFOrMATION WArNING ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE EDGE SANDER DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! POWer SUPPLY MAGNeTIC SWITCH ANd eMerGeNCY STOP bUTTON WArNING: YOUR EDGE SANDER MUST BE CONNECTED TO A... -
Page 5: Specifications
8) 4” dust chute. 18) End table lock handle. 9) Motor (220V). 19) End table. 10) Timing belt tension adjustment. SPeCIFICATIONS MODEL KC-108-OSC Belt 6” x 108” Oscillating stroke 1/4” Table size (front) 37” x 7 3/4” Table size (side) 19”... -
Page 6: Assembly And Setup
ASSeMbLY & SeTUP UNPACKING ANd SeTTING UP YOUr SANder Warning! This sander weighs 356 lbs, use material handling equipment when moving shipping crate and removing sander from the crate. Carefully unpack the sander and all loose items inside the cabinet base. This sander must be placed on a flat and even floor capable of supporting the machine weight. -
Page 7: Sanding Belt Tracking Adjustment
AdJUSTMeNTS & CHANGING SANdING beLT SANdING beLT TrACKING AdJUSTMeNT Warning! Disconnect power from power source before attempting to adjust this edge sander. To prolong the life of the sanding belt and to avoid any slippage of the belt off the drums, proper sanding belt tracking is important to maintain the sanding belt running straight on the drums. -
Page 8: Maintenance
CHANGING SANdING beLT & MAINTeNANCe CHANGING THe SANdING beLT continued..Warning! Disconnect power from power source before attempting to change the sanding belt. 3) Pull the tension lever (A) Fig.12 completely to the left “loose” position as shown. 4) Remove the used sanding belt from both rollers. 5) The sanding belt runs counterclockwise on the rollers, before installing a new sanding belt on the rollers, make sure the arrows on the inside of the sanding belt correspond to the belt rotation label on the safety guard on the right side...
Need help?
Do you have a question about the KC-108-OSC and is the answer not in the manual?
Questions and answers