Related Manuals for Enterasys WS-AP3705i
Summary of Contents for Enterasys WS-AP3705i
- Page 1 Enterasys Wireless ® Wireless Access Point Access Points Installation Guide WS-AP3705i Draft P/N 9034646...
- Page 2 Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.
- Page 3 It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please go to www.enterasys.com/support/ or contact Enterasys Customer Support at 353 61 705586 (Ireland). Draft...
- Page 4 SJ/T 11363-2006 standard. This table shows where these substances may be found in the supply chain of Enterasys’ electronic information products, as of the date of sale of the enclosed product. Note that some of the component types listed above may or may not be a part of the enclosed product.
- Page 5 CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc., on behalf of itself and its Affiliates (as hereinafter defined) (“Enterasys”) that sets forth Your rights and obligations with respect to the Enterasys software program/firmware (including any accompanying documentation, hardware or media) (“Program”) in the package...
- Page 6 Enterasys, and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii) the use, copying and deployment of the Program. You also grant to Enterasys and its authorized...
- Page 7 Agreement. 12. WAIVER. A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing and will not be construed as a waiver of any subsequent breach of such term or condition. Enterasys’ failure to enforce a term upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion.
-
Page 8: Table Of Contents
Unpacking the WS-AP3705i ........................2-1 Accessories ..............................2-1 WS-AP3705i Installation Procedures ......................2-2 Mounting the WS-AP3705i to a Flat Drop Ceiling ..................2-2 Mounting the WS-AP3705i to a Protruded Drop Ceiling ................2-3 Mounting the WS-AP3705i to a Wall ......................2-6 Mounting on a Junction Box ........................ - Page 9 Enterasys Wireless WS-AP3705i Front View ..................1-2 WS-AP3705i Back View ........................1-3 Mounting the WS-AP3705i on a Flat Drop Ceiling (no bracket) ............2-3 Attaching the Ceiling Mount Assembly to the T-Rail ................2-4 Mounting the AP to the Ceiling Mount Assembly ................2-5 Optional Wall Mounting Bracket (WS-MB3705-01) ................
-
Page 10: About This Guide
About This Guide The guide describes how to mount and connect cables to the Enterasys Wireless WS-AP3705i. In addition, this guide provides information on the product certifications and national approvals for the WS-AP3705i. Note: This guide does not provide information on configuration of the Enterasys Wireless APs. -
Page 11: Related Documents
The manual listed below can be obtained from the World Wide Web in Adobe Acrobat Portable Document Format (PDF) at the following site: https://extranet.enterasys.com/downloads/ • Enterasys Wireless Convergence Software User Guide Typographical Conventions The following typographical conventions and icons are used in this document. blue type Indicates a hypertext link. -
Page 12: Getting Help
Getting Help For additional support related to the WS-AP3705i or this document, contact Enterasys Networks using one of the following methods: World Wide Web www.enterasys.com/support/ Phone 1-800-872-8440 (toll-free in U.S. and Canada) or 1-978-684-1000 For the Enterasys Networks Support toll-free number in your country: www.enterasys.com/support/... -
Page 13: Ws-Ap3705I Overview
T-bar rail. Mounting brackets are available as optional accessories for mounting of the WS-AP3705i to walls and protruded drop ceilings. The WS-AP3705i is an 802.11n AP that also supports 802.11a/802.11g and 802.11b legacy devices. It is delivered in a round, compact enclosure. The WS-AP3705i contains four internal antennas, providing range and coverage versatility. -
Page 14: Ws-Ap3705I Led Indicators
The WS-AP3705i provides four LED indicators (see Figure 1-1). The LEDs provide status information (see Table 1-1) on the current state of the WS-AP3705i. For more information, see the Enterasys Wireless Convergence Software User Guide. Table 1-1 WS-AP3705i LED Status Indicators Icon Status... -
Page 15: Console Port
1-3) for debug purposes. This port enables connection of a console device to the WS-AP3705i through a serial cable. The AP must be removed from the wall or ceiling mount to enable access to the console port. The console device can be a PC or workstation running a VT-100 terminal adapter emulator, or a VT-100 terminal. -
Page 16: Reset Switch
Power over Ethernet (PoE). Reset Switch The WS-AP3705i provides a Reset Switch to reset or restore factory default configurations. Use a pen tip or a nail to press the switch button through the hole (located on the side of the AP). If you hold down the button for less than 5 seconds, the WS-AP3705i performs a software interrupt, causing the AP to drop all connections and reset. -
Page 17: Chapter 2: Installation
Enterasys Networks if there are any signs of damage. Refer to “Getting Help” on page xi for details. Accessories The following is a list of accessories available for the Enterasys Wireless WS-AP3705i. For ordering information, contact your Enterasys sales representative. • Wall mount/Junction box bracket –... -
Page 18: Ws-Ap3705I Installation Procedures
A flat drop ceiling is a drop ceiling in which the ceiling tiles are flat across the T-bar rails on which they rest. To mount the WS-AP3705i to a flat drop ceiling, you do not need an extra mounting bracket. To attach the WS-AP3705i to a flat drop ceiling: Remove the ceiling panels around the drop ceiling rails where you intend to mount the AP. -
Page 19: Mounting The Ws-Ap3705I To A Protruded Drop Ceiling
WS-AP3705i Installation Procedures Place the back of the WS-AP3705i against the T-bar rail and turn the AP so that the mount clips snap over the rail, as shown in Figure 2-1. Figure 2-1 shows the AP mounting operation from a perspective above the rail, in which case the twist is clockwise. From a perspective below the AP, you are turning the AP in a counterclockwise motion. -
Page 20: Attaching The Ceiling Mount Assembly To The T-Rail
WS-AP3705i Installation Procedures Attach the bracket to the drop ceiling T-bar rails by sliding the slide plates over the rails as shown (Figure 2-2), then insert and tighten the two included machine screws into the mount holes in the ceiling mount plate and slide plate. -
Page 21: Mounting The Ap To The Ceiling Mount Assembly
AP until it stops. Warning: If the rivet is not inserted as described in this step, there is a risk the Enterasys Wireless WS-AP3705i will fall from the bracket. -
Page 22: Mounting The Ws-Ap3705I To A Wall
(near the ceiling for maximum radio wave dispersion) but in reach of the Ethernet cable and a wall power outlet if the application does not use Power over Ethernet. Place the WS-AP3705i wall mounting bracket firmly against the wall surface. Secure the bracket to the wall with three 1.5” screws and wall plugs if applicable (see Figure 2-5). -
Page 23: Mounting On A Junction Box
AP. Then depress the top of the rivet until it is completely seated. Warning: If the rivet is not inserted as described in this step, there is a risk the Enterasys Wireless WS-AP3705i will fall from the bracket. -
Page 24: Mounting On An Existing Mount Plate
AP. Then depress the top of the rivet until it is completely seated. Warning: If the rivet is not inserted as described in this step, there is a risk the Enterasys Wireless WS-AP3705i will fall from the bracket. -
Page 25: Network And Power Connections
AP. Then depress the top of the rivet until it is completely seated. Warning: If the rivet is not inserted as described in this step, there is a risk the Enterasys Wireless WS-AP3705i will fall from the bracket. -
Page 26: Connecting The Dc Power Supply To The Ws-Ap3705I
Note: Currently, the DC connector on the back of the WS-AP3705i is non-functional. There is no wall mount for a DC power supply. To connect the power supply to the WS-AP3705i for everyday operation, mount the AP and plug in the power supply as described in the section, “Mounting the WS-AP3705i to a... -
Page 27: Appendix A: Specifications
Specifications This appendix lists the specifications for the Enterasys Wireless WS-AP3705i. Table A-1 Specifications for the WS-AP3705i Item Specification Enclosure material Metal base, plastic housing Power source 802.3af compliant PoE PD, (Currently,Non-functional) 48V DC input Power consumption < 12.94W (Max.) Outside dimensions (max) 6.62"... - Page 28 Draft...
-
Page 29: Appendix B: Regulatory Information
This appendix provides regulatory information for the Enterasys Wireless WS-AP3705i. Warning: Changes or modifications made to the WS-AP3705i which are not expressly approved by Enterasys could void the user's authority to operate the equipment. Only authorized Enterasys service personnel are permitted to service the system. Procedures that should be performed only by Enterasys personnel are clearly identified in this guide. -
Page 30: Usa Conformance Standards
• IEEE 802.3af (PoE) Warning: The WS-AP3705i must be installed and used in strict accordance with the manufacturer's instructions as described in this guide and related documentation for the device to which the WS- AP3705i is connected. Any other installation or use of the product violates FCC Part 15 regulations. -
Page 31: Canada
22 cm de distance entre la source de rayonnement et votre corps. European Community The WS-AP3705i is designed for use in the European Union and other countries with similar regulatory restrictions where the end user or installer is allowed to configure the WS-AP3705i for Draft... -
Page 32: Declaration Of Conformity In Languages Of The European Community
WS-AP3705i will use the proper frequencies and power outputs for that country code. The WS-AP3705i is intended for indoor use and must be installed in a proper indoor location. Contact local Authority for procedure to follow and regulatory information. For more details on legal combinations of frequencies, power levels and antennas, contact Enterasys. -
Page 33: European Conformance Standards
Šiuo Enterasys deklaruoja, kad šis Radio LAN device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Latvian Ar šo Enterasys deklar , ka Radio LAN device atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem Lithuanian Enterasys deklaruoja, kad Radio LAN device atitinka 1999/5/EC Direktyvos esminius reikalavimus ir kitas nuostatas". -
Page 34: Conditions Of Use In The European Community
The WS-AP3705i must not be operated until configured for the customer’s geographic location. Caution: The user or installer is responsible to ensure that the WS-AP3705i is operated according to channel limitations, indoor / outdoor restrictions, license requirements, and within power level limits for the current country of operation. -
Page 35: European Spectrum Usage Rules
Indoor or outdoor Switzerland Indoor only Indoor only Indoor or outdoor Indoor or outdoor Turkey Indoor only Indoor only Indoor or outdoor Indoor or outdoor Indoor only Indoor only Indoor or outdoor Indoor or outdoor Draft Enterasys Wireless WS-AP3705i Install Guide B-7... -
Page 36: Certifications Of Other Countries
Enterasys Wireless WS-AP3705i Certifications of Other Countries The WS-AP3705i has been certified for use in various other countries. Once the correct country code is selected, the Wireless AP automatically uses the proper frequencies and power outputs for that country code.