National Instruments BNC-2110 Installation Manual
  1. Manuals
  2. Brands
  3. National Instruments Manuals
  4. Adapter
  5. BNC-2110
  6. Installation manual

National Instruments BNC-2110 Installation Manual

Desktop and din rail-mountable bnc adapter for multifunction daq devices
Hide thumbs Also See for BNC-2110:

Advertisement

Table of Contents

INSTALLATION GUIDE

BNC-2110
Desktop and DIN Rail-Mountable BNC Adapter
for Multifunction DAQ Devices

What You Need to Get Started

This installation guide describes how to install and configure your
BNC-2110 accessory with an E Series, S Series, or NI 671X/673X
waveform generation Multifunction DAQ device.
The BNC-2110 is a desktop and DIN rail-mountable BNC adapter you
can connect to data acquisition (DAQ) devices. The BNC-2110 includes
15 BNC connectors, a terminal block with 30 pins for signal connections,
and a 68-pin I/O connector that connects to the E Series, S Series, and
waveform generation Multifunction DAQ devices. The BNC-2110 is ideal
for simplifying connections between your measurement apparatus and your
DAQ device in laboratory, test, and production environments.
To set up and use your BNC-2110 accessory, you need the following:
❑
BNC-2110 BNC Adapter
❑
BNC-2110 Installation Guide
❑
Multifunction DAQ device and the appropriate cable
❑
Small flathead screwdriver (supplied)
For detailed specifications for the BNC-2110, refer to the Specifications
section.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BNC-2110 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for National Instruments BNC-2110

Summary of Contents for National Instruments BNC-2110

  • Page 1: Installation Guide

    DAQ device in laboratory, test, and production environments. What You Need to Get Started To set up and use your BNC-2110 accessory, you need the following: ❑ BNC-2110 BNC Adapter ❑...

  • Page 2: Installing Your Bnc-2110

    Installing Your BNC-2110 To connect your BNC-2110 to your DAQ device, refer to Figure 1 as you complete the following steps. Consult your computer user manual or technical reference manual for specific instructions and warnings. Note If you have not already installed your DAQ device, refer to the DAQ Quick Start Guide for instructions.

  • Page 3: Connecting The Cables

    When you have finished using the BNC-2110, power off any external signals connected to the BNC-2110 before you power off your computer. The BNC-2110 is not designed for input voltages greater than 42 V, even if a Caution user-installed voltage divider reduces the voltage to within the input range of the DAQ device.

  • Page 4: Configuring The Bnc-2110

    This section describes how to configure your BNC-2110 accessory. Figure 2 shows the front panel of the BNC-2110. With NI-DAQmx, National Instruments has revised its terminal names so they are Note easier to understand and more consistent among NI hardware and software products.
  • Page 5 Table 2 describes the BNC connectors on the front panel of the BNC-2110. Refer to the Connecting Digital/Timing I/O section for terminal block connector descriptions.

  • Page 6: Measuring Floating Signals

    Measuring Floating Signals You can use the BNC-2110 to measure floating and ground-referenced analog input signals. To measure floating signal sources, move the switch located below the BNC connector for the AI channel you are using to the floating source switch position (labeled FS). In the floating source switch position, the amplifier negative terminal connects to ground through a 5 kΩ...

  • Page 7: Connecting Analog Outputs

    Multifunction DAQ devices are available on the front panel of the BNC-2110. Refer to your DAQ device documentation for information on using these signals. Table 4 describes the digital terminals on the front panel of the BNC-2110. Table 4. BNC-2110 Digital Terminal Descriptions Terminal Description PFI <1..9>...

  • Page 8: Specifications

    Refer to your DAQ device user manual for more information on using this signal. E Series and S Series devices only Specifications This section lists the specifications of the BNC-2110. These specifications are typical at 25 °C unless otherwise specified. Physical Dimensions ..........19.05 by 10.48 by 3.51 cm...

  • Page 9: Electromagnetic Compatibility

    Relative humidity ........5 to 90% noncondensing Safety The BNC-2110 meets the requirements of the following standards for safety and electrical equipment for measurement, control, and laboratory use: • IEC 61010-1, EN 61010-1 • UL 3111-1, UL 61010B-1 • CAN/CSA C22.2 No. 1010.1...
  • Page 10 National Instruments Corporation. Product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or...

Table of Contents