Table of Contents
Advertisement
三.安裝原則
1.安裝前請先檢查：
l. 附件：說明書、風管圈、油杯。
ll. 性能：接上電源檢查照明與馬達鍵是否正常。
lll.此電器必須接上地線以免導致受傷或損壞。
2.風管長度：
使用直徑8吋的風管更能提高排風之效率。
排風出口至機體之距離應盡量避免過長，以免氣流擠壓於管內影
響其排風效果。
抽油煙機之安裝高度係指爐面至機身底面之距離，建議參考高度
為26-30 英吋。抽油煙機若能越接近爐面則其排煙效果越佳。
3.理想安裝位置：
安裝於爐台之上方抽油煙機底部邊緣距地面約在 62 – 64 吋之間
(抽油煙機底部與瓦斯爐上方不得超過30吋)。
4.鑽穿牆洞：
先量好彎管正對牆面位置，釘頭與牆壁間最多保持1/4 吋距離做掛
勾之用，此舉有助機身保持水平。
然後在壁面畫好鑽洞範圍，再使用電鑽鑽穿牆壁鑽洞時應要留意
牆壁結構和質料切勿破壞牆洞以外之璧面。
裝設機身及排氣管：在已選定的安裝位置上，釘上螺絲釘。
調整機身兩側之掛勾（吊鐵），將機身懸掛於螺絲釘上。
懸掛後，機身要保持一定水平。
按已選好排氣管的適當位置，選擇適當長度的直管進行裝設。
本風管座已在出廠前套入出風口，安裝時請將風管照一般方式反
方向套入即可。安裝前先以強力膠注入風管圈後將風管圈崁入，再
用封膠封住風管圈，以避免清潔劑泡沫流出。
3.
III. Installation Guidelines
A. Please Inspect the Following Before Installation:
l. Enclosed Items: manual, duct collar, oil cup
ll. Performance: Check if light and motor switch appear normal after
connecting the power.
lll. This electrical appliance must be connected to the ground outlet to avoid
accidents or damaging the appliance.
B. Exhaust Pipe Length:
Using an 8-inch diameter exhaust pipe can improve ventilation efficiency.The
distance from the exhaust opening to the body of the hood should not be too
long. Otherwise, the airflow gets trapped inside the pipe and affects the
exhaust function.The ideal distance from the range hood to the stove top should
be 26-30 inches. This distance should be measured from the bottom of the range
hood to the top of the stove.The closer the range hood is to the stove top the
more effective the exhaust ventilation.
C. Ideal Installation Position:
The range hood should be installed with the bottom edge of the range hood
62-64 inches from the floor. (The distance between the bottom of the range
hood and the top of the gas stove should not exceed 30 inches).
D. Drilling a Hole on the Wall:
Measure the spot on the wall where the L-shape exhaust pipe will be placed.
The screw heads should stick out ¼ inches from the wall for the range hood
to be mounted, which also allows the range hood to stay leveled when installed.
Then make marks on the wall where you are going to drill the holes. Before
drilling holes in the wall, be sure to check the structure of the wall and the
material behind the wall so it will not be damaged after drilling.
Then proceed to drill holes on the marked areas.
Installing range hood and exhaust pipe:
Install the screws into the wall on marked areas. Adjust the hooks (hanging rail)
on both sides of the range hood and hang the range hood on the screws.
After the range hood is mounted, check to make sure it's balanced.
Based on the position marked for the exhaust pipe, pick a straight pipe cut to
an appropriate length and install. An air outlet has been attached to the exhaust
pipe unit before leaving the factory. Attach the exhaust pipe to the straight pipe
where the two units connect. Before installation, put some glue on the inside
ring of the exhaust pipe opening, so the pipes can be securely attached.
Then secure the attachment point with plastic tape to prevent cleaning foams
from leaking during cleaning.
3.
Advertisement
Table of Contents
