Gree GWH18TC-S3DNA1D Service Manual page 22

Service Manual
● Under swing left and right mode, when the status is switched from off to
status directly; if press this button again within 2s, the change of swing status will also depend on the circulation sequence stated above.
7. button
Press this button can select up & down swing angle. Fan blow angle can be selected circularly as below:
● When selecting " ", air conditioner is blowing fan automatically. Horizontal louver will automatically swing up & down at maximum angle.
● When selecting "
、
● When selecting " 、 、 " , air conditioner is blowing fan at fixed angle. Horizontal louver will send air at the fixed angle.
● Hold " "button above 2s to set your required swing angle. When reaching your required angle, release the button.
Note:
● " 、 、 " may not be available. When air conditioner receives this signal, the air conditioner will blow fan automatically.
● Press this button continuously more than 2s, the main unit will swing back and forth from up to down, and then loosen the button, the unit
will stop swinging and present position of guide louver will be kept immediately.
● Under swing up and down mode, when the status is switched from off to
status directly; if press this button again within 2s,the change of swing status will also depend on the circulation sequence stated above.
8. SLEEP button
Press this button, can select Sleep 1 (
Cancel is defaulted.
Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run for one hour, the main unit setting temperature will increase 1 ℃ , two hours,
setting temperature increased 2 ℃ , then the unit will run at this setting temperature; In Heat mode: sleep status after run for one hour, the
setting temperature will decrease 1 , two hours, setting temperature will decrease 2℃ , then the unit will run at this setting temperature.
● Sleep 2 is sleep mode 2, that is air conditioner will run according to the presetting a group of sleep temperature curve.
● Sleep 3-the sleep curve setting under Sleep mode by DIY;
(1)Under Sleep 3 mode, press "Turbo" button for a long time, remote controller enters into user individuation sleep setting status, at this time,
the time of remote controller will display "1hour", the setting temperature "88" will display the corresponding temperature
of last setting sleep curve and blink (The first entering will display according to the initial curve setting value of original factory);
(2)Adjust "+" and "-" button, could change the corresponding setting temperature, after adjusted, press "Turbo" button for confirmation;
(3) At this time, 1hour will be automatically increased at the timer postion on the remote control, (that are "2hours" or "3hours" or "8hours"),
the place of setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours temperature setting finished,sleep,curve setting finished, at this time, the remote
controller will resume the original timer display; temperature display will resume to original setting temperature.
● Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user individuation sleep setting status,
but do not change the temperature, press "Turbo" button directly for confirmation. Note: In the above presetting or enquiry procedure, if
continuously within 10s, there is no button pressed, the sleep curve setting within 10s, there is no button pressed, the sleep curve setting
status will be automatically quit and resume to display the original displaying. In the presetting or enquiry procedure, press "ON/OFF" button,
"Mode" button, "Timer" button or "Sleep" button, the sleep curve setting or enquiry status will quit similarly.
9. I FEEL button
Press this button to start I FEEL function and "
will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor temperature according to the
detected temperature. Press this button again to close I FEEL function and "
● Please put the remote controller near user when this function is set. Do not put the remote controller near the object of high temperature
or low temperature in order to avoid detecting inaccurate ambient temperature.
10. TIMER ON / TIMER OFF button
● TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, "
blinks. Press " ▲ " or "
or decrease 1min. Hold " ▲ " or "
confirm it. The word "ON" will stop blinking. "
up, press "TIMER ON" button to cancel it.
Technical Information
no display
(horizontal louvers stops
at current position)
、 、 ", air conditioner is blowing fan at fixed position. Horizontal louver will stop at the fixed position.
、
), Sleep 2 (
" will be displayed on the remote controller. After this function is set, the remote controller
"button to adjust TIMER ON setting. After each pressing " ▲ " or "
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER ON" to
" icon resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is started
, if press this button again 2s later,
, if press this button again 2s later,
), Sleep 3 ( ) and cancel the Sleep, circulate between these, after electrified, Sleep
" will disappear.
" icon disappears and the word "ON" on remote controller
" button, TIMER ON setting will increase
status will switch to off
status will switch to off
19