Specifications - Makita BJN160 Instruction Manual

ENGLISH (Original instructions)
1-1. Button
1-2. Red indicator
1-3. Battery cartridge
2-1. Star marking
3-1. Die holder
3-2. Lock nut
3-3. Loosen
3-4. Wrench
4-1. Gauge for cutting stainless:
1.2 mm (3/64")
4-2. Gauge for cutting mild steel:
1.6 mm (1/16")
4-3. Notch
5-1. Slide switch

SPECIFICATIONS

Max. cutting capacities
Min. cutting radius
Strokes per minute (min
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
Noise
The typical A-weighted
according to EN60745:
Model BJN160
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model BJN161
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Explanation of general view
6-1. Indicating lamp
7-1. Die holder
7-2. Die
7-3. Bolts
7-4. Hex wrench
8-1. Punch
8-2. Punch holder
8-3. Screw
8-4. Hex wrench
8-5. Loosen
8-6. Tighten
9-1. Punch
9-2. Notch
10-1. Bolts
Model
Steel up to 400 N/mm
Steel up to 600 N/mm
Aluminum up to 200 N/mm
Outside edge
Inside edge
-1
)
Overall length
Net weight
Rated voltage
noise level determined
) : 72 dB (A)
pA
) : 73 dB (A)
pA
BJN160
2
1.6 mm / 16 ga
2
1.2 mm / 18 ga
2
2.5 mm / 12 ga
50 mm
45 mm
1,900
313 mm
2.1 kg
D.C. 14.4 V
ENE037-1
Vibration
The vibration
determined according to EN60745:
ENG905-1
Model BJN160
Work mode : cutting sheet metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model BJN161
Work mode : cutting sheet metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
4
10-2. Die
10-3. Punch
10-4. Die holder
13-1. From the side view
13-2. Cutting head should be at a right
angle (90 ﾟ) to cutting surface.
14-1. Limit mark
15-1. Holder cap cover
15-2. Notch
15-3. Screwdriver
16-1. Brush holder cap
16-2. Screwdriver
BJN161
1.6 mm / 16 ga
1.2 mm / 18 ga
2.5 mm / 12 ga
50 mm
45 mm
1,900
313 mm
2.2 kg
D.C. 18 V
total value (tri-axial
2
) : 7.0 m/s
h
2
2
) : 6.5 m/s
h
2
ENG900-1
vector sum)
ENG901-1