Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LAMI Freesia 55C
Summary of Contents for LAMI Freesia 55C
- Page 1 Instruction Manual LAMI CORPORATION INC.
-
Page 2: Table Of Contents
┣ Power Connection for re-winding Device ....................P 6 ┗ Fuse Installation Method..........................P 7 ■ Name of Each Part ┣ Main Body of Freesia 55C.......................... P 8 ┣ Operation Panel............................P 9 ┗ Foot Switch ..............................P 10 ■ Before Processing Laminate P 11 ┗... -
Page 3: Precautions Before Use P
Precautions before Use List of Labels Attached to the Product ▼Nameplate label (porting) ▼Rated label ▼Cover switch restriction label ▼Jamming and entangling warning ▼Grounding instruction label ▼Fuse label label Ground connection must be done. ▼Emergency stop switch label ▼Tension control label Meaning of Symbols This document uses symbols to explain the degree of harm and damage caused by incorrect use of the product and to prevent harm on customers and others or damage on properties. -
Page 4: Precautions For Handling
Precautions for Handling Warning Power cable included in the product must be used. Do not use power supply not indicated on the product. Do not place heavy objects on power cable, place cables nearby heating devices, or complex wiring. Do not process power cable or use damaged power cable. Accurately insert to the end of electrode. -
Page 5: Place For Installation
Place for Installation This device shall be installed in the following places. ●Horizontal and stable place Use as slanted or in unstable state may result in adverse effects such as paper return. Also, unexpected accidents can occur. ●Place where exclusive power outlet is available Do not use power types other than the rated voltage regulated on this Manual. -
Page 6: Characteristics And Confirmation Of Parts P
Characteristics ●Pressure can be adjusted in 8 steps automatically ●Speed of laminate processing can be adjusted step by step ●Rotation and stopping of the roller can be done using foot switch ●Transparent safety cover Confirmation of Parts The following parts and documents are included in the main body. If there is a missing part, contact a nearby business office of our company or store from which the product was purchased. -
Page 7: Installation Of The Machine Stand Assembly Method
Installation of the Machine Stand Assembly Method ①M6 screw (4 EA x 2 places) ②M6 screw 2 EA ③M6 screw 2 EA Stand is assembly type. Use hex wrench to install the stand while being careful about left and right directions. ※... -
Page 8: Fuse Installation Method
Fuse Installation Method Fuse is placed nearby the power switch on the rear of right surface and power switch of the Re-winding device. (Spare fuse is only included in the Re-winding device.) Take out the fuse using flat-head driver to check disconnection of the fuse. If it is disconnected, replace with a new fuse before supplying power again. -
Page 9: Name Of Each Part Main Body Of Freesia-55C
Name of Each Part Main Body of Freesia-55C Right Side of Main Body ① Stand ② Media holder shaft ③ Film shaft for under-film ④ Idle roller (front) ⑤ Front signboard ⑥ Finger jamming prevention cover ⑦ Laminate roll ⑧ Stay bar (reinforcement bar) ⑨... -
Page 10: Operation Panel
Operation Panel LCD Display Panel Speed Thickness Forward and reverse rotation of roller Current status Displayed during laminate processing STOP Displayed when laminate processing is stopped FORWARD If 【FORWARD】 is shown on the LCD panel, the roller rotates in forward direction. REVERSE If 【REVERSE】... -
Page 11: Foot Switch
Buttons on the operating panel 【℃ ℃ ℃ ℃ /℉ ℉ ℉ ℉ 】 button 【TEMPERATURE】 button This button is not used. This button is not used. 【SPEED】 button 【THICKNESS】 button This button is not used. Rotational speed of the laminate roller can be adjusted within 0 ~ 1.9 m/min. -
Page 12: Before Processing Laminate About Laminate Film
Before Processing Laminate About Laminate Film There are two types of laminate film including 「roll type」 and 「pack type」. This product uses 「cold roll film」 type. ※ 「Pack type」 and 「hot roll film」 cannot be used. Thickness of the laminate film is selected according to the use. Thickness (µ) Thickness of the cold roll film used by this product ranges from 20 µ... -
Page 13: Cold Laminate Processing Installation And Processing Of Cold Laminate Film
Cold Laminate Processing Installation and Processing of Cold Laminate Film 【1】 Install the paper tube holder on the film shaft. All 6 film shafts are common parts. Use hex wrench to move or fixate the branch pipe holder. Fixate 4 sides of each branch pipe holder. - Page 14 Only cut the release paper on the laminate film and rotate the laminate roller until the cross section of the release paper cut touches the re- winding paper tube. Here, hold the release paper so that it does not get entangled. When the release paper touches the re-winding paper tube, attach it using cellophane tape to finish installation.
- Page 15 Release liner Paper tube for re-winding release liner Laminate film Under-film After setting the re-winding shaft, please turn the shaft holder cover Paper tube for product Re-winding 【5】 Perform laminate processing. 1 : Use the 【THICKNESS】 button to adjust pressure (gap) according to thickness of processing material and 【PRESS/RELEASE】...
-
Page 16: Maintenance P
Maintenance This product is composed of many rollers, and they must be cleaned according to usage. The laminate can be maintained in desirable state by cleaning the rollers. Cleaning of Roller Clean each roller since rollers have paper scraps and dusts attached. Caution The roller must be stopped when cleaning. -
Page 17: Troubleshooting
Troubleshooting The following measures are taken for troubleshooting. Power does not turn on · machine does not function Insert outlet plug and check power switch This product is used at AC 100V~240V. Make sure that the outlet plug is correctly connected. Check that the power switch on the back of the main body is turned on. -
Page 18: Others P
Panel processing : 1.2mm · 1.7mm · 2.3mm · 3mm · 5mm· 8mm Maximum power consumption AC 100V~240V 100W Dimensions 1838 × 591 × 1196 (mm) (width × length × height) Weight 137 kg ※ Specifications may be changed without notice for improvements. Contact LAMI CORPORATION INC. 81-6-6453-1871...