Pc-programmable temperature transmitters (60 pages)
Summary of Contents for Rosemount 3051
Page 1
00825-0100-4007, Rev DD January 2017 ™ Rosemount 3051 Pressure Transmitter and Rosemount 3051CF Series Flowmeters ® with 4–20 mA HART Revision 5 and 7 Protocol Note Before installing the transmitter, confirm the correct device driver is loaded on the host systems.
Quick Start Guide NOTICE This guide provides basic guidelines for Rosemount 3051 Transmitters. It does not provide instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 HART Revision 5 and 7...
Rosemount 3051 device revisions and drivers Table 1 provides the information necessary to ensure you have the correct device driver and documentation for your device. Table 1. Rosemount 3051 Device Revisions and Files Review Review Identify device Find device driver...
January 2017 Quick Start Guide Transmitter installation Mount the transmitter Liquid applications Coplanar In-line 1. Place taps to the side of the line. 2. Mount beside or below the taps. Flow 3. Mount the transmitter so that the drain/vent valves are oriented upward.
Page 5
Quick Start Guide January 2017 Figure 1. Panel and Pipe Mounting Panel mount Pipe mount Coplanar flange Traditional flange Rosemount 3051T panel bolts are customer supplied.
Page 6
January 2017 Quick Start Guide Bolting considerations If the transmitter installation requires assembly of the process flanges, manifolds, or flange adapters, follow the assembly guidelines to ensure a tight seal for optimal performance characteristics of the transmitters. Use only bolts ™...
Page 7
Quick Start Guide January 2017 Table 2. Torque Values for the Flange and Flange Adapter Bolts Bolt material Head markings Initial torque Final torque Carbon Steel (CS) 300 in-lb 650 in-lb Stainless Steel (SST) 150 in-lb 300 in-lb Environmental seal for housing Thread sealing (PTFE) tape or paste on male threads of conduit is required to ®...
The security switch allows (unlocked symbol) or prevents (locked symbol) any configuration of the transmitter. Default security is off (unlocked symbol). 1. Rosemount 3051C original position aligns with “H” side; Rosemount 3051T original position is the opposite side of bracket holes.
Quick Start Guide January 2017 Use the following procedure to change the switch configuration: 1. If the transmitter is installed, secure the loop, and remove power. 2. Remove the housing cover opposite the field terminal side. Do not remove the instrument cover in explosive atmospheres when the circuit is live. 3.
Page 10
Quick Start Guide Installation of the transient protection terminal block does not provide transient protection unless the Rosemount 3051 case is properly grounded. Do not run signal wiring in conduit or open trays with power wiring, or near heavy electrical equipment.
AMS Device Manager. Verifying configuration with a Field Communicator A Rosemount 3051 DD must be installed on the Field Communicator to verify configuration. Fast Key sequences for the latest DD are shown in Table 3 on page 11.
Page 12
January 2017 Quick Start Guide Table 3. Device Revision 9 and 10 (HART 7), DD Revision 1 Fast Key Sequence Fast Key sequence Function HART 7 HART 5 Descriptor 2, 2, 7, 1, 5 2, 2, 7, 1, 4 Digital to Analog Trim (4–20 mA Output) 3, 4, 2 3, 4, 2 Disable Configuration Buttons...
Page 13
Switch HART revision mode If the HART configuration tool is not capable of communicating with HART Revision 7, the Rosemount 3051 will load a generic menu with limited capability. The following procedures will switch the HART revision mode from the generic menu: 1.
When performing a zero trim, ensure that the equalization valve is open and all wet legs are filled to the correct level. It is not recommended to zero an absolute transmitter, Rosemount 3051CA or 3051TA models. 1. Choose your trim procedure.
2. Press and hold the Zero button for two seconds to perform a digital zero trim. Safety instrumented systems installation For safety certified installations, refer to Rosemount 3051 HART Revision 5 and 7 Reference Manual for installation procedure and system requirements.
Standards: FM Class 3600 – 2011, FM Class 3610 – 2010, FM Class 3611 – 2004, FM Class 3810 – 2005 Markings: IS CL I, DIV 1, GP A, B, C, D when connected per Rosemount drawing 03031-1019 (–50 °C ≤ T ≤...
Page 17
Quick Start Guide January 2017 2. The Rosemount 3051 Transmitter with the transient terminal block (option code T1) will not pass the 500 Vrms dielectric strength test and this must be taken into account during installation. Canada Explosionproof, Dust-Ignitionproof, Intrinsic Safety and Nonincendive Certificate: 1053834 Standards: ANSI/ISA 12.27.01-2003, CSA Std.
Page 18
January 2017 Quick Start Guide 4. Some variants of the equipment have reduced markings on the nameplate. Refer to the Certificate for full equipment marking. ATEX Intrinsic Safety and Dust Certificate: BAS97ATEX1089X; Baseefa11ATEX0275X Standards: EN60079-0:2012, EN60079-11:2012, EN60079-31:2009 II 1 G Ex ia IIC T5/T4 Ga, T5(–60 °C ≤ T ≤...
Page 19
Quick Start Guide January 2017 N1 ATEX Type n and Dust Certificate: BAS00ATEX3105X; Baseefa11ATEX0275X Standards: EN60079-0:2012, EN60079-15:2010, EN60079-31:2009 II 3 G Ex nA IIC T5 Gc (–40 °C ≤ T ≤ +70 °C); Markings: 105 °C Da (–20 °C ≤ T ≤...
Page 20
January 2017 Quick Start Guide Table 10. Input Parameters Parameter HART Fieldbus/PROFIBUS Voltage U 30 V 30 V Current I 200 mA 300 mA Power P 0.9 W 1.3 W 0.012 μF 0 μF Capacitance C Inductance L 0 mH 0 mH Special Conditions for Safe Use (X): 1.
Page 21
Quick Start Guide January 2017 Brazil INMETRO Flameproof Certificate: UL-BR 13.0643X Standards: ABNT NBR IEC60079-0:2008 + Errata 1:2011, ABNT NBR IEC60079-1:2009 + Errata 1:2011, ABNT NBR IEC60079-26:2008 + Errata 1:2008 Markings: Ex d IIC T6/T5 Ga/Gb, T6(–50 °C ≤ T ≤...
Page 22
January 2017 Quick Start Guide Table 13. Input Parameters Parameter FISCO Voltage U 17.5 V Current I 380 mA Power P 5.32 W Capacitance C <5 nF <10 μH Inductance L Special Conditions for Safe Use (X): 1. If the equipment is fitted with an optional 90 V transient suppressor, it is not capable of withstanding the 500 V insulation test required by ABNT NBR IEC 60079-11.
Page 23
Ex-certified associated apparatus to establish explosion protection system that can be used in explosive gas atmospheres. Wiring and terminals should comply with the instruction manual of both Rosemount 644 and associated apparatus. The cables between Rosemount 644 and associated apparatus should be shielded cables (the cables must have insulated shield).
Page 24
January 2017 Quick Start Guide 7. End users are not permitted to change any intern components but to settle the problem in conjunction with the manufacturer to avoid damage to the product. 8. During installation, use and maintenance of this product, observe the following standards: GB3836.13-1997, GB3836.15-2000, GB3836.16-2006, GB50257-1996, GB12476.2-2006, GB15577-2007.
Page 25
Certificate: 23155 Requirements: Bureau Veritas Rules for the Classification of Steel Ships Application: Class notations: AUT-UMS, AUT-CCS, AUT-PORT and AUT-IMS; Pressure transmitter type 3051 cannot be installed on diesel engines Det Norske Veritas (DNV) Type Approval Certificate: TAA000004F Intended Use: DNV GL Rules for Classification — Ships and offshore units...
Page 26
January 2017 Quick Start Guide Application: Location classes Temperature Humidity Vibration Enclosure Lloyds Register (LR) Type Approval Certificate: 11/60002 Application: Environmental categories ENV1, ENV2, ENV3, and ENV5 Custody Transfer - Measurement Canada Accuracy Approval Certificate: AG-0226; AG-0454; AG-0477...
Page 27
Quick Start Guide January 2017 Figure 11. Rosemount 3051 Declaration of Conformity...
Page 31
Quick Start Guide January 2017 Rosemount 3051 China RoHS List of Rosemount 3051 Parts with China RoHS Concentration above MCVs / Hazardous Substances Hexavalent Polybrominated Polybrominated Part Name Lead Mercury Cadmium Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr +6)
Page 32
+65 6777 0947 The Emerson logo is a trademark and service mark of Emerson Enquiries@AP.Emerson.com Electric Co. AMS, Rosemount, and Rosemount logotype are trademarks of Middle East and Africa Regional Office Emerson. Emerson Automation Solutions DTM is a trademark of the FDT Group.
Need help?
Do you have a question about the 3051 and is the answer not in the manual?
Questions and answers