Page 1
This will allow the recycling of raw materials and help protect the environment. FOR HELP OR ADVICE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR, OR SIP DIRECTLY ON: TEL: 01509500400 05726, 05728 & 05730 EMAIL: sales@sip-group.com or technical@sip-group.com www.sip-group.com...
Page 2
Conforms to the requirements of the following directive(s), as indicated. 2006/95/EC Low Voltage Directive 2004/108/EC EMC Directive 2011/65/EU RoHS Directive And the relevant harmonised standard(s), including EN 60974-1:2012 EN 60974-10:2007 Signed: …………………………………... Mr P. Ippaso - Managing Director - SIP (Industrial Products) Ltd Date: 06/05/2015.
SAFETY SYMBOLS USED THROUGHOUT THIS MANUAL NOTES Danger / Caution: Indicates risk of personal injury and/or the possibility of damage. Warning: Risk of electrical injury or damage! Note: Supplementary information. SAFETY INSTRUCTIONS Important: Please read the following instructions carefully, failure to do so could lead to serious personal injury and / or damage to the invert- er welder.
Page 5
MAINTAIN THE INVERTER WELDER WITH CARE: Keep the earth clamp and electrode hold- er clean for the best and safest performance. USE ONLY RECOMMENDED ACCESSORIES: Consult this user manual, your distributor or SIP directly for recommended accessories. Follow the instructions that accompany the ac- cessories.
Page 6
The work should be clamped firmly whilst welding, If its loose it could result in personal injury or damage to the machine or item that is being welded. Ref. Ref. No. Description SIP Part No. Description SIP Part No. Do not attempt any repairs to the welder unless you are a competent electrician or Handle...
Page 7
Frequently inspect leads for wear, splits, cracks and any other damage. Imme- diately replace those with worn or damaged insulation to avoid a possibly lethal shock from bare leads. Ref. Ref. No. Description SIP Part No. Description SIP Part No. FIRE Handle WE01-00085...
Page 8
GLARE AND BURNS Ref. Ref. No. Description SIP Part No. Description SIP Part No. The welding arc produces ultraviolet (UV) and infrared (IR) rays as well as extreme tem- peratures that can cause injury to your eyes and skin. Do not look at the welding arc...
Page 9
WIRING DIAGRAM - 05730 SAFETY INSTRUCTIONS….cont First aid facilities and a qualified first aid person should be available for each shift unless medical facilities are close by for immediate treatment of flash burns to the eyes and skin. Flammable hair products should not be used by persons intending to weld. Warn bystanders not to watch the arc and not to expose themselves to the welding arc rays or to hot metal.
Page 10
SAFETY INSTRUCTIONS….cont WIRING DIAGRAM - 05726 & 28 Vapours from chlorinated solvents can be decomposed by the heat of the arc (or flame) to form phosgene a highly toxic gas and other lung and eye-irritating products. The ultra violet (radiant) energy of the arc can also decompose tri- chloroethylene and perchlorethylene vapours to form phosgene.
Burns through thin metal. arc welding. Connecting to the power supply 05726: This SIP Inverter welder (05726) is fitted with a standard 230v ~ 13 amp type plug. Be- Symptom Possible Cause Solution fore using the Inverter welder, inspect the mains lead and plug to ensure that neither are damaged.
Page 12
ELECTRICAL CONNECTION….cont MAINTENANCE Connecting to the power supply 05728 and 05730: Clear dust from the machine at regular intervals, if used in a dirty environment the machine should be cleaned once a month. The 05728 and 05730 are supplied without a plug fitted, they must not be connected Check all connections are clean and tight, if there is any oxidization clean the to a standard 13A supply, consult the technical specification table (page14) for the connection with a mild abrasive or wire brush.
GUARANTEE Guarantee: WELDING These SIP Inverter welders are covered by a 12 month parts and labour warranty cov- Ensure all protective equipment is worn and bystanders are not in Caution: ering failure due to manufacturers defects. This does not cover failure due to misuse or the vicinity.
Bottle of argon gas Filler rod Ref. No. Description Ref. No. Description * SIP Tig torch: SR17V, Part Number 05029. Negative Dinse Socket Welding selector switch The required tungsten diameter is determined by the thickness of the material to be...
GETTING TO KNOW YOUR INVERTER WELDER….cont OPERATING INSTRUCTIONS ARC WELDING There are no hard and fast rules by which a particular gauge of electrode is selected, usually this is determined by the type of welding required and the thickness of the workpiece e.g.
Need help?
Do you have a question about the Weldmate HG 05726 and is the answer not in the manual?
Questions and answers