Advertisement
Advertisement
Table of Contents
Related Manuals for Major Science MP-300
Summary of Contents for Major Science MP-300
- Page 1 Instruction Manual PowerPoint Power Supply, Model MP-300...
-
Page 2: Table Of Contents
Table of Contents Packing list Warning Safety Information Product Specifications Product Description Controls and Features Installation Instructions Operation Instructions Troubleshooting Guide Warranty... -
Page 3: Packing List
Packing list MP-250 or CS-300: - 1 x MP-300 - 1 x Power Cord for power supply - 1 x Extra fuse inside power plug on the rear of unit - 1 x power supply instruction manual... -
Page 4: Warning
Warning This power supply series has been tested and found to comply with the limits for the CE regulation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This power supply series generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. -
Page 5: Safety Information
Safety Information Use high level precautions against any electrical device. Before connecting with the electrical supply, check the supply voltage is within the range stated at the rating label, and this device must be earthed. Place the unit in a safe and dry location not touching any surrounding material. Follow safety precautions for chemicals and dangerous materials. - Page 6 Avoiding Damage to the Instrument 1. Do not attempt to operate the device if damaged. 2. Protect this unit from physical damage, corrosive agents and extreme temperatures (direct sunlight etc). 3. For proper ventilation, leave at least 10 cm of space behind the instrument, and at least 5 cm of space on each side.
-
Page 7: Product Specifications
Product Specifications Output Voltage / Inc 2-300V / 1V Output Current / Inc 1-700mA / 1mA Max. Watt 150W Operating Constants Voltage or Current Control Microprocessor Controller Terminator Pairs 4 pairs Timer 1~999 mins with alarm, continuous No Load detect Safety Device Leakage detect Overload detect... -
Page 8: Product Description
This manual describes the setup and operation of the 300V Power Supply including important information on safety and maintenance of the unit. The MP-300 power supply are capable of running DNA/RNA electrophoresis, Electroblotting, SDS-PAGE, native PAGE applications, and second-dimension SDS-PAGE applications. - Page 9 Introduction Overview MP-300 Power Supplies are recognized as one of the most advanced power supply equipped with outstanding specifications to cover the majority of electrophoresis applications on the market. Sufficient and accurate output voltages, four pairs of terminator, compact size and CE compliance for safety concerns can deliver accurate and reliable experimental results from one experiment to another.
-
Page 10: Controls And Features
Controls and Features Front Control Panel Key -- to increase either Voltage or Current or Time value Key - to decrease either Voltage or Time value Key – to activate or stop the unit Key – to temporarily interrupt power to an operation in progress without terminating electrophoresis and to resume power after pausing without resetting the timer. -
Page 11: Installation Instructions
Installation Instructions Place on a sturdy and level surface in a safe, dry place, and connect with a buffer filled electrophoresis system. Operation Instructions 1. Place the power supply on a sturdy and level surface in a safe, dry place, away from laboratory traffic. - Page 12 7. Press Key, and then press Key or Key to adjust timer (minute) upon your request if setting time is required. It will auto stop when the timer is up. 8. Press Key to start the run. The LED is lit. 9.
-
Page 13: Troubleshooting Guide
Troubleshooting Guide Many operating problems may be solved by carefully reading and following the instructions in this manual. Some suggestions for troubleshooting are given below. Should these suggestions not resolve the problem, contact the SERVICE DEPARTMENT or a distributor in your region for assistance. If troubleshooting service is required, please include a full description of the problem. -
Page 14: Error Messages
High voltage DISABLE No Load alarm on the application is set to Display Screen run on a very low current Error Messages Err1; power Current exceeds Check that the correct supply stops; setting running buffer and buffer alarm sounds. concentration have been used Check that cables are connected properly... - Page 15 A58, A57 safety. etc. Maintenance MP-300 Power Supply series only requires little maintenance to assure reliable operation. The housing may be cleaned with a dry cloth.
-
Page 16: Warranty
Warranty These Power Supply units have a warranty against manufacturing and material faults of twelve months from date of customer receipt. If any defects occur during this warranty period, your dealer will repair or replace the defective parts free of charge. This warranty does not cover defects occurring by accident or misuse or defects caused by improper operation.