Related Manuals for Major Science MS 250V
Summary of Contents for Major Science MS 250V
-
Page 1: Power Supply
MS 250V / MS 300V Power Supply Instruction Manual Catalog Nos. MP-250V MP-300V www.majorsci.com service@majorsci.com Version 01A October 20, 2009... -
Page 2: Un Packing List
1 x UK Plug Power Cord or 1 x Israel Plug Power Cord - 1 x MS 250V / MS 300V Power Supply Instruction Manual Major Science is liable for all missing or damaged parts / accessories within 7 days after customer received this instrument package. Please contact Major Science immediately regarding this issue. -
Page 3: Packing List
- 1 x US Plug Power Cord or 1 x Euro Plug Power Cord or 1 x UK Plug Power Cord or 1 x Israel Plug Power Cord - 1 x MS 250V / MS 300V Power Supply Instruction Manual Signed: Date:... -
Page 4: Table Of Contents
Table of Contents Un packing list Packing list Warning Safety Information Product Specifications Product Description Introduction Overview Controls and Features Installation Instructions Operation Instructions Troubleshooting Guide Maintenance Ordering Information Warranty... -
Page 5: Warning
Major Science MS 250V / MS 300V power supply series has been tested and found to comply with the limits for the CE regulation. Also, MS 250V / MS 300V power supply series is RoHS compliant to deliver confident product, which meets the environmental directive. -
Page 6: Safety Information
Avoiding Electrical Shock Follow the guidelines below to ensure safe operation of the unit. MS 250V / MS 300V power supply series has been designed to use with shielded wires thus minimizing any potential shock hazard to the user. Major Science recommends against the use of unshielded wires. - Page 7 2. NEVER access dangerous chemistry or other material to prevent possible hazards of explosion and damage. Symbols The symbols used on MS 250V / MS 300V Power Supply are explained below. Used on MS Power Supply to indicate an area where a potential shock hazard may exist.
-
Page 8: Product Specifications
Product Specifications Output Voltage / Inc 2~250V / 1V for MP-250V 2~300V / 1V for MP-300V Output Current / Inc 1~700mA / 1mA Max. Watt 150W Operating Constants Voltage or Current Control Microprocessor Controller Terminator Pairs 4 pairs Timer 1~999 mins with alarm, continuous Safety Device No Load detection Leakage detection... -
Page 9: Product Description
This manual describes the setup and operation of MS 250V / 300V Power Supply, including important information on safety and maintenance of the unit. MS 250V and MS 300V power supplies are capable of running horizontal &... -
Page 10: Introduction
Introduction Overview Major Science MS 250V and 300V Power Supplies are recognized as one of the most advanced power supplies equipped with outstanding specifications to cover the majority of electrophoresis applications on the market. Sufficient and accurate output voltages, four pairs of terminator, compact size, RoHS and CE compliance for safety concerns can deliver accurate and reliable experimental results from one experiment to another. -
Page 11: Controls And Features
Controls and Features Please refer to Figures on the following page for the location of the following controls and features. MS 250V Power Supply Cat. No.: MP-250V MS 300V Power Supply Cat. No.: MP-300V Front Control Panel Key – to increase either Voltage or Current or Time value... -
Page 12: Installation Instructions
Key – to set or select Timer mode Installation Instructions Major Science MS 250V / MS 300V Power Supply series is actually an already installed instrument. As long as it is placed on a sturdy and level surface in a safe, dry place, and is further connected with well-prepared electrophoresis system, it is ready for operation. -
Page 13: Operation Instructions
Operation Instructions 1. Place MS 250V / MS 300V Power Supply series on a sturdy and level surface in a safe, dry place, away from laboratory traffic. 2. Ensure that the AC power switch is OFF, and then plug the three-pronged... - Page 14 flashing. 10. Press Key to temporarily interrupt the run if necessary. , the LED is flashing. Press Key to restart the run. 11. Press Key again to stop the unit at any time if necessary. 12. When the run is completed, operation stops with alarm and the screen shows .
-
Page 15: Troubleshooting Guide
Use the correct cords. The fuse has blown Replace the fuse Repeated fuse broken Hardware failure Contact Major Science service department Electrophoresis leads are Check the connections to the power supply not connected to the and on your electrophoresis cell to make sure power supply or to the the connection is intact;... - Page 16 2. Call Technical Service or e-mail to service@majorsci.com 3. If the unit must be shipped back for repair, contact Major Science or the distributor for a Return Authorization Number and shipping instructions. The unit will be repaired as quickly as possible and returned to you.
- Page 17 For additional fuses, contact Major Science co. ltd. To replace the fuse: 1. Turn off the main power switch on the rear of MS 250V or MS 300V Power Supply and detach the power cord from the rear of MS 250V or MS 300V Power Supply.
-
Page 18: Maintenance
Maintenance MS 250V and 300V Power Supply series uses all solid-state components and should require no maintenance or recalibration under normal use. The housing may be cleaned with a dry cloth. If the unit must be returned for repair, contact our SERVICE DEPARTMENT or your local distributor for shipping instruction. -
Page 19: Warranty
All claims made under this warranty must be presented to Major Science within two years following the date of delivery of the product to the customer. - Page 20 MEMO...