Development Hardware Connections; Attach Module To Prototyping Board - RabbitCore RCM3000 Getting Started Manual

2.3 Development Hardware Connections

There are four steps to connecting the Prototyping Board for use with Dynamic C and the
sample programs:
1. Attach the RCM3000 module to the Prototyping Board.
2. Connect the programming cable between the RCM3000 module and the workstation PC.
3. Connect the module's Ethernet port to a PC's Ethernet port, or to an Ethernet network.
4. Connect the power supply to the Prototyping Board.

2.3.1 Attach Module to Prototyping Board

Turn the RCM3000 series module so that the Ethernet connector end of the module
extends off the Prototyping Board, as shown in Figure 3 below. Align the module headers
J1 and J2 into sockets J21 and J13 on the Prototyping Board.
GND
GND
VBAT
EXT
/RES
IN
SM0
/IOWR
PG5
RCM3000
PG7
PE1
PE4
PE6
PF7
PF5
PB7
PB5
PB3
PB0
GND
GND
VBAT
EXT
/RES
IN
SM0
/IOWR
PG5
PG7
PE1
PE4
PE6
PF7
PF5
PB7
PB5
PB3
PB0
Figure 3. Installing the RCM3000 Series Module on the Prototyping Board
Although you can install a single module into either the
on the Prototyping Board, all the Prototyping Board features (switches, LEDs, serial port
drivers, etc.) are connected to the
module in the MASTER
NOTE: It is important that you line up the pins on headers J1 and J2 of the RCM3000
series module exactly with the corresponding pins of headers J12 and J13 on the Proto-
typing Board. The header pins may become bent or damaged if the pin alignment is off-
set, and the module will not work. Permanent electrical damage to the module may also
result if a misaligned module is powered up.
Press the module's pins firmly into the Prototyping Board headers.
Getting Started
RN1
NC PD1 PD0
GND
+3.3V PD7 PD6
VRAM PD3 PD2
SM1 PD5 PD4
/IORD PG3 PG2
PG1 PG0
PG4
PD4
PG6 PD5
PC5
PE0 PC4
PC3
PE3 PC2
PC1
PE5 PC0
PF0
PE7 PF1
PF6 PF2 PF3
PF4 PA0 PA1
PB6 PA2 PA3
RCM3000 RABBITCORE
PB4 PA4 PA5 RCM1
J14
PB2 PA6 PA7
SLAVE
UX10
/RES PE4 GND
MASTER
J1 J3
C1
RC15 RCM3000
RCM2
RABBITCORE
RC24
R1 RC19
R4
RC20
RC23
R3
UX9
C3
R5
R2
RC14
RC17 RC22
RC16
RC13
UX3
RC21
RC12
R21
RC10
RC2
RC11
NC PD1 PD0
+3.3V PD7 PD6
VRAM PD3 PD2
SM1 PD5 PD4
/IORD PG3 PG2
PG4 PG1 PG0
J13
J12
PG6 PD4 PD5
PE0 PC5 PC4
PE3 PC3 PC2
PE5 PC1 PC0
PE7 PF0 PF1
U1
PF6 PF2 PF3
PF4 PA0 PA1
C5
PB6 PA2 PA3
C8
J12
PB4 PA4 PA5
C6
RESET
S2
PB2 PA6 PA7
RxC TxC
/RES PE4 GND
C7
J5
J4
RS-232
TxB RxB GND
MASTER
position.
RN5
R20
R17
U4
+5V
Battery
+3.3V
BT1
J15
UX11
UX2
GND GND
GND
+3.3V +3.3V
+3.3V +3.3V
+5V
+5V
RC6 RC7
C9
U3
UX5
R14
RC9
UX7
RCM3000 PROTOTYPING BOARD
J13
S3
PG6 PG7
DS2 DISPLAY BOARD
DS1
MASTER
position. We recommend you install a single
L1
C17
J11
D1
C13
2.5 MM JACK
D2 GND +DC
C12
U5
+5V
+3.3V
GND
+5V +5V
J8 UX4
RC25
RC4
C16 RC5
DISPLAY BOARD
U6
C14
RC27
U3
RC28
RC29
RC26
UX13
J10 J7
DISPLAY BOARD
or the SLAVE position
11