Sony STR-DN1000 Service Manual page 71

QQ
3 7 63 1515 0
HDMI BOARD IC3508 SII9134CTU (HDMI TRANSMITTER)
Pin No. Pin Name
1
2
3
4
5
6 to 9 SD3 to SD0
10
11
12
13
14 IOVCC33
15
16
17
18
19
20
21
22
23
24
25
26
27 EXT_SWG
TE
L 13942296513 28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45 DCCPWR5V
46
47
48
49
50
51
52
www
53 IOVCC33
54
55
.
56 to 63 D35 to D28
64
65
http://www.xiaoyu163.com
I/O
DE I Data enable signal input from the video controller and HDMI receiver
HSYNC I Horizontal sync signal input from the video controller and HDMI receiver
VSYNC I Vertical sync signal input from the video controller and HDMI receiver
SPDIF I S/PDIF signal input from the HDMI receiver
MCLK I Master clock signal input from the HDMI receiver
I PCM audio signal input from the HDMI receiver
WS I L/R sampling clock signal input from the HDMI receiver
SCK I Bit clock signal input from the HDMI receiver
CVCC18 - Power supply terminal (+1.8V)
GND - Ground terminal
- Power supply terminal (+3.3V)
DCLK I Not used
DR0 I Not used
DL0 I Not used
DR1 I Not used
DL1 I Not used
DR2 I Not used
DL2 I Not used
DR3 I Not used
DL3 I Not used
INT O Interrupt signal output to the HDMI controller
RESET# I Reset signal input from the HDMI controller
AGND - Ground terminal
- Not used
PVCC1 - Power supply terminal (+1.8V)
AGND - Ground terminal
TXC- O TMDS clock (negative) output to the HDMI OUT connector
TXC+ O TMDS clock (positive) output to the HDMI OUT connector
AVCC18 - Power supply terminal (+1.8V)
TX0- O TMDS data (negative) output to the HDMI OUT connector
TX0+ O TMDS data (positive) output to the HDMI OUT connector
AGND - Ground terminal
TX1- O TMDS data (negative) output to the HDMI OUT connector
TX1+ O TMDS data (positive) output to the HDMI OUT connector
AVCC18 - Power supply terminal (+1.8V)
TX2- O TMDS data (negative) output to the HDMI OUT connector
TX2+ O TMDS data (positive) output to the HDMI OUT connector
AGND - Ground terminal
PVCC2 - Power supply terminal (+1.8V)
AGND - Ground terminal
AVCC33 - Power supply terminal (+3.3V)
I Power supply voltage (+5V) input terminal
DSCL O I2C clock signal output to the HDMI OUT connector
DSDA I/O I2C data bus with the HDMI OUT connector
CSCL I I2C clock signal input from the HDMI controller
CSDA I/O I2C data bus with the HDMI controller, EEPROM, and HDMI receiver
CI2CA - Not used
HPD I Hot plug detection signal input from the HDMI OUT connector
TMODE - Not used
- Power supply terminal (+3.3V)
x ao
y
GND - Ground terminal
VPP18 - Power supply terminal (+1.8V)
i
I Serial data input from the video controller and HDMI receiver
CVCC18 - Power supply terminal (+1.8V)
GND - Ground terminal
http://www.xiaoyu163.com
8
Q Q
3 6 7 1 3
u163
.
2 9 9 4 2 8
Description
"L": reset
1 5 0 5 8 2 9 9 4
m
co
STR-DN1000
9 9
2 8 9 9
71