Sony STR-DN1000 Service Manual page 14

STR-DN1000
QQ
3 7 63 1515 0
SPECIAL MENU MODE
Procedure:
1. Press the [ ] button to turn on the main power, then while pressing the [INPUT SELECTOR +] button, press the [A.F.D.], [2CH/A.
?/1
DIRECT], [MUSIC], [MOVIE] button in order, the message "SPECIALIZE" appears.
2. Press the [ ]/[ ] buttons on the remote commander, the message "< SPECIAL>" appears.
M m
3. Press the [ ] button on the remote commander, the item is appears.
,
4. Each time the [ ]/[ ] buttons on the remote commander is pressed, the item is switched in order as follows.
M m
Some items can change the content. Display the cursor by pressing the [
by pressing the [ ]/[ ] buttons on the remote commander, and fi x the content by pressing the [
M m
when you want to change the content of the item.
5. To release from this mode, while pressing the [INPUT SELECTOR +] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC],
[MOVIE] button in order again, the message "OFF" appears.
Items
Model/Destination change
Main micom version display
Farouja version display
CGROM micom version display
HDMI micom version display
DSP serial fl ash version display
FLI update
HD update
TE
L 13942296513
HDCP key read
Video Factroy
Auto cal mic test
FL display fonts test
DSP halt
Super reset
RAM watch menu
EEPROM debug
Protector on/off
www
Audio swap
Volume value display (FL/FR)
.
Volume value display (SL/SR)
14
http://www.xiaoyu163.com
Display
When [,] button on the remote commander is pressed, the message "N1
** XX" is appears
MODEL
**: Destination
XX: fx or at
X.XX: System controller software version
N1 ** MX.XX
**: Destination
F.Ver X.XX X.XX: Farouja software version
G.Ver X.XX X.XX: CGROM controller software version
H.Ver X.XX X.XX: HDMI controller software version
S.Ver X.XX X.XX: Serial fl ash software version
When [,] button on the remote commander is pressed, the message "ON"
FLI UPDATE
or "OFF" is appears
Switching with [M]/[m] buttons on the remote commander
When [,] button on the remote commander is pressed, the message "ON"
HD UPDATE or "OFF" is appears
Switching with [M]/[m] buttons on the remote commander
When [,] button on the remote commander is pressed, the message "ON"
HDCP KEY or "OFF" is appears
Switching with [M]/[m] buttons on the remote commander
V. FACTORY Not used for the servicing
When [,] button on the remote commander is pressed, the message
"SOURCE" or "MIC" is appears
SP OUT
Switching with [M]/[m] buttons on the remote commander
SOURCE: normal mode, MIC: mode that output audio from mic input
When [,] button on the remote commander is pressed, the message
"0X**=X" is appears
FL FONT
**: 20 to FF, X: character
Switching with [M]/[m] buttons on the remote commander
When [,] button on the remote commander is pressed, the message "ON"
DSP HALT
or "OFF" is appears
Switching with [M]/[m] buttons on the remote commander
Not used for the servicing
RESET When EEPROM initialization is required, perform the "memory clearing
mode"
When [,] button on the remote commander is pressed, the message
"XXXXXXXXXX" is appears
RAM WATCH
XXXXXXXXXX: Various internal RAM
Switching with [M]/[m] buttons on the remote commander
When [,] button on the remote commander is pressed, the message "****
XX" is appears
EEPROM
****: EEPROM address, XX: EEPROM data
Switching with [M]/[m] buttons on the remote commander
When [,] button on the remote commander is pressed, the message "ON"
PROTECTOR or "OFF" is appears
Switching with [M]/[m] buttons on the remote commander
When [,] button on the remote commander is pressed, the message
"XXXXXXXXXX" is appears
SWAP MODE
XXXXXXXXXX: audio swap mode
x ao u163
Switching with [M]/[m] buttons on the remote commander
y
****: Front L-ch volume value, XXXX: Front R-ch volume value (for design
L****RXXXX
i
evaluation)
****: Surround L-ch volume value, XXXX: Surround R-ch volume value (for
S****SXXXX
design evaluation)
http://www.xiaoyu163.com
2 9
8
] button on the remote commander, and changing the content
,
<
Remark
Q Q
3 6 7 1 3 1 5
co
.
9 4 2 8
] button on the remote commander
0 5 8 2 9 9 4 2 8
m
9 9
9 9