Installation - Haier HW80-1479 User Manual

Troubleshooting
Problem Cause
Excessive foam floats • Detergent is not a appropriate
drum and/or deter-
gent drawer. • Excessive use of detergent.
Automatic adjustment • Washing programme duration will be
of washing time. adjusted.
Spinning fails. • Unbalance of laundry.
Unsatisfactory wash- • Degree of pollution does not agree with
ing result selected programme.
• Detergent quantitiy was not sufficient.
• Maximum load has been exceeded.
• Laundry was unevenly distributed in the
drum..
Washing powder • Insolubke particles of detergent can re-
residues are on the
main as white spots on the laundry.
.
laundry
Laundry has grey • Caused by fats such as oils, creams or
patches. ointments
Note:
If too much foam is inspected during spin cycle, motor stops and drain pump will be ac-
tivated for 90 seconds. If that elimination of foam fails up to 3 times, programme ends
without spinning.
Should the error messages reappear even after the taken measures, switch off the appli-
ance, disconnect the power supply and contact the customer service.
In case of power failure
The current programme and its setting will be saved. When power supply is restored op-
eration will be resumed.
IIf a power failure cuts an operating wash programme door opening is mechanically
blocked. To get out any laundry water level should not be seen in the glassy porthole of the
door. - Danger of burns! Water level has to be lowered as described in "Pump filter". Not
till then pull lever beneath service flap until door is unlocked by a gentle click. Afterwards
refix all parts.
22
GB
Solution
• Check detergent recommen-
dations.
• Reduce amount of detergent.
• This is normal and doesn't af-
fect functionality.
• Check machine load and laun-
dry and run a spinning pro-
gramme again. .
• Select an other programme.
• Choose the detergent acc.to the
degree of pollution and acc. to
manufaturer specifications.
• Reduce loading.
• Loose the laundry.
• Perform extra rinse.
• Try to brush the points from the dry
laundry.
• Choose an other detergent.
• Pretreat the laundry with a special
cleaner.
GB
Preparation
▶ Take the appliance out of the packaging.
▶ Remove all packaging material including polystyrene base, keep them out of childrens
reach. While opening the package, water drops may be seen on plastic bag and port-
hole. This normal phenomenon results from water tests in the factory.
Note:
Keep all packaging materials out of childrens reach and dispose them in an environmen-
tally friendly manner.
Adjusting the bottom cover board
When opening the shrink package, you will find a calci-
um-plastic board and a felt. The board is used for re-
ducing noise after covering the bottom of the cabinet.
1. Past the felt on one side of the calcium-plastic
board.
2. Lay the washing machine down to its side, porthole
pointing upwards, bottom side towards operator and
screw off the four bolts.
3. Place the calcium-plastic board with felt towards
inside, screw the bolts through the four holes on the
board on to the tub firmly. Finally set the machine up-
right again.
Dismantle the transportation bolts
The transportation bolts are designed for clamping
anti-vibration components inside the appliance during
transportation to prevent inner damage.
1. Remove the back cover.
2. Remove all 4 bolts on the rear side and take out
plastic spacers (A) from inner side of the machine.
3. Replace back cover by inserting it in the two gaps
its convexity is facing out.
4. Fill left holes with blanking plugs.
Note:
Keep the transportation bolts in a safe place for later
use. Whenever the appliance is to be moved at first
reinstall the bolts.

Installation

1 2
3
1 2
A
4
3
3
23