Sony HCD-SHAKE5 Service Manual page 14

HCD-SHAKE5/SHAKE6D
[PROTECT KIND CHECK TEST MODE]
This mode is used to check types of protect occurred during
protector on.
Procedure:
1. During protection on, fl uorescent indicator tube shows blinking
message "PROTECT EXX" where "EXX" represent the error
code.
2. Press [] button and [‒ / ] (SHAKE5) / [‒/PRESET‒]
(SHAKE6D) button simultaneously.
3. Fluorescent indicator tube display will toggle between
"PROTECT" message and protector kind message display.
Below table explains on protector kind.
Error Protector
Code Message
E01 "AMP OCP"
E03 "POWER
SUPPLY"
E04 "DC DETECT"
E05 "THERMISTOR"
E06 "FAN BLOCK"
To release from this mode:
Press [] button and [‒ / ] (SHAKE5) / [‒/PRESET‒]
(SHAKE6D) button simultaneously again or unplug & re-plug in
the power cord.
If speaker does not have output even if the set status is not in
PROTECT mode, the following defect might be possible:
Defects Possible cause
RESET defect Reset signal status from micom is not 'H'.
If the PROTECT mode is "POWER SUPPLY", there is possibility
of unusual power supply of any of the AMP IC or Pre-amplifi er.
14
Description
The over current condition to
MOSFET occurs by defect of
MOSFET or defect of PS output
line.
Defect of power supply circuit
to AMP
DC appears in SP terminal by
defect of AMP IC and MOS-
FET.
Unusual heat up of MOSFET by
improper assembly of heat sink,
destruction of MOSFET etc.
Defect of DC FAN and DC FAN
driver circuit
[MODEL & DEST WRITE MODE]
This mode is used to set software model & destination.
This mode is only available when no permanent model &
destination is stored.
Procedure:
1. Press [OPTIONS] (SHAKE5) / [X] (SHAKE6D) button and
[FOOTBALL] button simultaneously and hold for 5 seconds.
2. Fluorescent indicator tube display will show "M XXXXX".
3. Press [+ / ] (SHAKE5) / [+/PRESET+] (SHAKE6D) /
[‒ / ] (SHAKE5) / [‒/PRESET‒] (SHAKE6D) button to
select the model based on the set's model.
Product Code
STORM-JR-CD
STORM-JR-DVD
4. Press [ENTER] button.
5. Fluorescent indicator tube display will show "D XXXXX".
6. Press [+ / ] (SHAKE5) / [+/PRESET+] (SHAKE6D) /
[‒ / ] (SHAKE5) / [‒/PRESET‒] (SHAKE6D) button to
select the destination based on the set's country.
Area Code Country
J1 Japan
JE1 Tourist
U2/CA2 America, Canada
CEL/CE1/ Europe (general)
CE2
CEK U.K.
RU1/RU3 Russia
AU1 Australia
CN1 China
E12 India, Pakistan, Morocco
E3/E93/ Middle East, Africa
SA2/E15 (South Africa), Iran
E4 Africa
EA3 Saudi Arabia
HK1/ Hong Kong, Philippines,
HK2/PL1/ Singapore, Malaysia,
SP1/SP2/ Thailand
SP6/TH1
KR2 Korea
TW2 Taiwan
E2, E32, Latin America (general),
E51, AR2 Chile, Peru, Argentina
BR1 Brazil
MX2, Mexico
MX4
7. Press [ENTER] button to confi rm the selection.
8. "RESET" appears on the fl uorescent indicator tube. After that,
the fl uorescent indicator tube becomes blank for a while, and
the system is reset.
9. Mode in [PANEL TEST MODE] again to confi rm on the
model & destination.
F. Tube display
"M STORM-JR"
"M STORM-JRD"
F. Tube display
"D J"
"D JE"
"D NA"
"D CE2"
"D CEK"
"D RU"
"D AU"
"D CN"
"D E12"
"D E3"
"D E12"
"D EA3"
"D ASIA"
"D KR"
"D TW"
"D LATIN"
"D BR"
"D MX"