HCD-SHAKE5/SHAKE6D
Pin No.
Pin Name
52
O-ANALOG-ASEL
53
O-ANALOG-CSEL
54
O-VIDEO-MUTE
55
O-MTK-BUSY
56
I-MTK-XIFCS
57
O-MTK-RESET
58
O-CD-MOTOR +
59
O-CD-MOTOR -
60
VCC
61
O-DIGITAL-SEL
62
VSS
63
I-CDM-LOAD-SW
64
I-CDM-UNLOAD-SW
65
AD-KEY0
66
I-DSP-INT
67
O-DSP-MUTE
68
/I-FAN-BLOCK
69
I-FAN-DRIVE
70
/I-THERMISTOR-DET
71
/I-DC-DET
72
I-DAMP-OCP
73
O-DAMP-RESET
74
/I-SD-FAST
75
I-DSP SDA
76
I-DSP SCL
77
NO-USE
78
O-PCONT-DAMP
79
O-MTK-POWER-CTRL
O-RGB-TRANS-LED-
80
SPK
81
NO-USE
82
NO-USE
83
NO-USE
84
/I-HUB-OC-USB B
85
O-VBUS-OE
86
/I-HUB-OC-USB A
87
O-HUB-VBUS-DETECT
88
O-HUB-RESET
89
NO-USE
90
I-AD-KEY-1
91
I-MIC-DETECT
92
I-MASTER-VOLUME
93
O_PCONT_BTSTBY
94
AVSS
95
I-MODEL-DEST IN
96
VREF
97
AVCC
98
O-FL-LATCH
99
O-FL-SOUT
100
O-FL-CLK
56
I/O
O
Multiplexer selector A for Analog input
O
Multiplexer selector C for Analog input
O
Video Mute. "L" : mute On
O
BUSY Signal communication between MTK
I
MTK CHIP SELECT
O
MTK Reset Pin
O
CDM turning motor control signal output
O
CDM turning motor control signal output
I
Power supply terminal (+3.3V)
O
Digital Selector Pin
I
Ground terminal
I
CDM LOAD SW
I
CDM UNLOAD SW
I
Key input terminal (A/D input)
I
DSP Initialization completion interrupt signal
O
DSP Mute control . "H": Mute On
I
Fan Block Detection Pin. "L": Block On
I
Fan on/off control input signal. "H": On
I
Temperature protect pin. "L": Protect on
I
DC detection pin. "L": Protect on
I
Digital Amp over current protection pin. "L": Protect on
O
Digital Amp Reset Pin
I
Power Supply Shutdown Protection Detection Pin. "L": Protect on
I
DSP IC: Data signal for IIC communication
I
DSP IC: Clock signal for IIC communication
O
NO USE
O
Digital Amp Module Power Control Pin. "H": ON
O
Power Control pin for MTK
O
Transfer signal to RGB driver (driver for Speaker LED)
-
Not used
-
Not used
-
Not used
I
USB Overcurrent Detection input port B
O
MTK Vbus Output enable control pin
I
USB Overcurrent Detection input port A
O
Hub Power (V-DET) Control Port
O
MTK Hub reset pin
-
Not used
I
Key input terminal (A/D input)
I
Mic Input Detection pin. "H": Mic detected
I
Jog dial pulse input from the MASTER VOLUME encoder (A/D input)
O
BT Standby Power Control Pin. "H": ON
I
Ground terminal
I
Model and Destination setting terminal (A/D input)
I
A/D Converter reference voltage input terminal (+3.3V)
I
Power supply terminal (+3.3V)
O
Data Latch signal to FL CIG
O
Serial data output to FL CIG
O
Serial clock output to FL CIG
Description