Hearth & Home IFT-RC400 User Manual

Hearth & Home IFT-RC400 User Manual

Intellifire touch remote control
Hide thumbs Also See for IFT-RC400:

Advertisement

Introduction

This user guide serves as a quick reference to the screen,
functions and indicators on your IntelliFire™ Touch
Remote control.
SCREEN
INDICATOR BAR
ROOM TEMPERATURE
FUNCTIONS
DYNAMIC ICONS
IFT-RC400
IntelliFire™ Touch Remote Control
DISPLAY
SELECTION
INDEX
Hearth & Home Technologies • IFT-RC400 User Guide • 2326-983 Rev. C • 1/17

User Guide

Turn Flame On/Off

Toggle this function to turn ON or OFF your appliance.

Thermostat

You can set and maintain your desired room temperature
with the thermostat function. This function automatically
adjusts your appliance to maintain the desired set
temperature (ST).
To achieve the most accurate thermostat function, place
your remote control in the same general space that
you want to have the temperature controlled by your
appliance.
For
control away from direct radiant heat from the appliance,
adjacent windows and doors, HVAC vents, and direct
sunlight.
To use the thermostat function, access the main menu
screen on your remote, and select thermostat. Next,
simply select your desired set temperature by using the
arrow keys and press ON to confirm the setting. The
actual room temperature (RT), measured by your remote
control, will be displayed in the upper right corner of the
main menu screen. To turn the thermostat function off,
simply select thermostat on the main menu screen and
select OFF.
If the RT cools to more than 3 °F lower than the ST for
at least 2 minutes, then your appliance will automatically
turn ON. The thermostat function will automatically adjust
the flame height based on the difference between the RT
and the ST. As the RT rises closer to the ST, the flame
height will automatically adjust down. If the RT rises 2 °F
above the ST for at least 2 minutes, then your appliance
will automatically turn OFF.
During thermostat use, you will not be able to set your
desired flame height level. Your appliance will
automatically adjust flame height based on the difference
between the RT and ST.

Flame Height

You can set your desired flame height level to affect the
ambiance and control the heat output.
Your appliance will remember the previous flame height
setting and adjust the flame to that level 10 seconds after
start.
FUNCTIONS
best
results,
keep
your
remote
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IFT-RC400 and is the answer not in the manual?

Questions and answers

Jerry Brown
February 11, 2025

My remote is saying there is a communication error

1 comments:
Mr. Anderson
February 12, 2025

To fix a communication error on the Hearth & Home IFT-RC400 remote, try the following steps:

1. Verify that the home circuit breaker is on.
2. Ensure the master reset is on (if equipped).
3. If there is a power outage, install new batteries in the battery backup.

If the issue persists, contact your Hearth & Home Technologies dealer for further assistance.

This answer is automatically generated

Lawrence Brown
February 2, 2025

Room and fireplace surround gets too hot how can you lower the heat intensity?

1 comments:
Mr. Anderson
February 10, 2025

To lower the heat intensity of the Hearth & Home IFT-RC400 room and fireplace surround, use the thermostat mode. The IFT system automatically adjusts the flame intensity based on the difference between the desired and actual room temperature. As the actual temperature approaches the set temperature, the flame intensity will decrease. Additionally, ensure the IFT-RC400 is not placed directly in the path of an air draft or vent, as this can affect temperature readings.

This answer is automatically generated

Summary of Contents for Hearth & Home IFT-RC400

  • Page 1: User Guide

    Your appliance will remember the previous flame height setting and adjust the flame to that level 10 seconds after start. Hearth & Home Technologies • IFT-RC400 User Guide • 2326-983 Rev. C • 1/17...
  • Page 2: Child Lock

    When the flame is turned off, a post-purge time of approximately 20 minutes will occur. Cold-climate function and battery backup are disabled if * = Optional Feature a Power Vent is used. Hearth & Home Technologies • IFT-RC400 User Guide • 2326-983 Rev. C • 1/17...
  • Page 3 3. Double-beep from the remote will indicate that the remote will reset the 300-hour maintenance reminder. If the remote 300-hour maintenance message does not clear on the first try, repeat above steps. Hearth & Home Technologies • IFT-RC400 User Guide • 2326-983 Rev. C • 1/17...
  • Page 4 Verify home circuit breaker is on and master reset is on (if No power to appliance. message on-screen: equipped). “Remote Control Communication Power outage. Install new batteries in battery backup. Error.” Hearth & Home Technologies • IFT-RC400 User Guide • 2326-983 Rev. C • 1/17...
  • Page 5 2) This device may accept any interference, including interfer- Hearth & Home Technologies dealer, ence that may cause undesired operation of the device. please visit www.hearthnhome.com. Hearth & Home Technologies • IFT-RC400 User Guide • 2326-983 Rev. C • 1/17...

Table of Contents

Save PDF