Advertisement
Quick Links
Advertisement
Related Manuals for Autoglide CASA-50P
Summary of Contents for Autoglide CASA-50P
- Page 1 INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 1...
-
Page 2: Table Of Contents
4.1 Technical Data Sheet of Series. 4.2 Photocell Data Sheet. 4.3 Transmitter Data Sheet. 4.4 Flashing Light Data Sheet. 4.5 External Receiver Box Data Sheet. 5. Additional Information 5.1 Wire Connection of Photocell (Safety Beam). INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 2... -
Page 3: Warning
Keep all the components of CASA-50P system and this manual for further consultation • Be aware of the hazards that may exist in the procedures of installation and operation of the gate-automated system. -
Page 4: Installation
4. Flashing light 2.2 Description of Device a. Operation gear, b. Limit switch device, c. 24Vdc motor, d. Back-up batteries (Optional) e. Release device, f. Control panel, g. Terminals of devices, h. Green Box (Optional) INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 4... -
Page 5: Dimension Of Device
2.3 Dimension of Device. 2.4 Installation of Gear Motor and Gear Rack. INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 5... -
Page 6: Checking For Installation
If the LED display is in normal performing refer to “4.2.1”, you can control the gate by either transmitters or the button. On the board: “UP”-clockwise moving, “SET”- stop and “DOWN”- Counterclockwise moving INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 6... - Page 7 Push Button: 10-11 INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 7...
- Page 8 1, 2, 3 Step2: Press left button (A) on time, the LED display should show “LP” 4 , 5 Step3: The gate goes to Auto-learning, please wait for the learning process to be completed INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 8...
-
Page 9: Programmable Function Setting
There actions of the 1. Please do the function setting Pleas the function photocells/safety after H & J setting after 8 edge/loop detector 2. The factory setting is 3-1 when they detecting obstacles INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 9... - Page 10 (8-2) 15 seconds 18 seconds The flashing light blinks when the gate Pre-flashing starts to move The factory setting is (9-1) The flashing light blinks 3 seconds before the gate starts to move INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 10...
- Page 11 The factory setting is (J-0) function Open Photocell test Close 1.The factory setting is (L-0) function 2.if the function open Open Stop connector Close 1.The factory setting is (P-1) function 2. St Open INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 11...
- Page 12 Loop Detector Photocell 1 Closed Open No effect Open Reloads automatic closing time Stop during moving Open Reloads automatic closing time Closing Open Open Opening Open No effect The position of safety devices: INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 12...
-
Page 13: Recognition Of Led
27.10 cm/s 4.1 Photocell Data Sheet Detection type Through beam Operating distance 25 meters Response time 100ms Input voltage AC/DC 12~24V -20℃~+60℃ Operating Temperature Protection class IP54 Dimension 96mm * 45mm * 43mm INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 13... -
Page 14: Transmitter Data Sheet
Red LED (RX): ON (When Beam is Broken)Green(TX):ON Dimensions 96*45*43mm Output Method Relay Output Current Consumption TX: 35MA/Rx: 38MA (When beam aligned properly); TX: 35MA/ Rx: 20MA (When beam is broken) Water Proof IP54 INSTRUCTIONS CASA-50P SLIDING GATE OPENER Page 14... - Page 15 P600B PCB. And use an extra wire to connect terminals 2 and 5 on the receiver as a bridge. Proprietary Intellectual Property, Do not Distribute without authorization. All rights Reserved- Copyright@2015 Autoglide. www.autoglideglobal.com INSTRUCTIONS CASA-50P SLIDING GATE OPENER...
Need help?
Do you have a question about the CASA-50P and is the answer not in the manual?
Questions and answers