Subscribe to Our Youtube Channel
Related Manuals for Helipal Luminer QAV-X Storm Edition
Summary of Contents for Helipal Luminer QAV-X Storm Edition
- Page 1 Luminer QAV-X Storm Edition with HGLRC 3-in-1 SP Racing F3 Controller (w/ CleanFlight) USER MANUAL V1.0 Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 2 6) Never overcharge LiPo batteries. Do not charge above 4.2V per cell. When the battery is fully charged, disconnect it from the charger. Never leave the battery charger unattended during charging. 7) Never discharge batteries to below 3.3V per cell 8) Remove batteries when not using the drone. Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 3 Quick Start - Radiolink AT9 Radio Controller Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 4 Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 5 Quick Start - FrSky Taranis X9D Plus Radio Controller Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 6 Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 7 How to Control - Radiolink AT9 Radio Controller Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 8 How to Control - FrSky Taranis X9D Plus Radio Controller Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 9 Motors and propellers rotation Copyright@2016 HeliPal.com. All Rights Reserved...
-
Page 10: Fpv System
The bigger different in video frequency between drones, the less interference generated. LONG press to change Band SHORT press to change Channel Always check the supported channels of you FPV reception devices such as monitor, goggles Frequency Table Copyright@2016 HeliPal.com. All Rights Reserved... - Page 11 The receiver will stop flashing once the binding process complete and there will be a Signal Strength icon on the screen. Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 12 Go to [AUX-CH] -> ATTITUDE, apply the setting [CH8] = SwC [CH9] = SwF [CH10] = SwA below: [CH] = CH5 [SW3] = SwG [SW2] = NUL [STABL.] = 0% [STABL.] = 50% [ARCO.] = 100% Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 13 10) Go to [F/S], apply the setting below: [1] [AILE] = NOR [2] [ELEV] = NOR [3] [THRO] = 15% [4] [RUDD] = -70% [5] [ATTI] = NOR [6] [AUX1] = NOR [7] [AUX2] = NOR [8] [AUX3] = NOR Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 14 You can find the procedures below: Download OPENTX program by isiting http://www.open-tx.org/downloads.html. Always use the latest version Use the latest OPENTX 2.1 branch. Download the latest helipal profile for our drone here (Please unzip before use): www.helipal.com/download/uav/srd-taranis-x9d-plus.zip http://goo.gl/PZQeWO Turn on your radio by holding both lower trims towards the center and turn on transmitter at the same time, you will enter BootLoader mode.
- Page 15 Remember to click ! to write the profile back to your radio. Unplug USB cable, switch off transmitter and switch on again. Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 16 VFAS : Battery voltage RSSI : Radio signal VFAS- : Lowest battery voltage RSSI- : Lowest radio T1 : Timer (Auto start with throttle, Switch H to reset) VFAS: Battery voltage RSSI : Radio signal Copyright@2016 HeliPal.com. All Rights Reserved...
- Page 17 How to use the battery strap? Secure the battery leads along with the battery strap. Copyright@2016 HeliPal.com. All Rights Reserved...
Need help?
Do you have a question about the Luminer QAV-X Storm Edition and is the answer not in the manual?
Questions and answers