Functional Description - Makita DFJ202 Instruction Manual

Material
DFJ202 Outer material: Polyester (100%)
DFJ203 Inner material: Polyester (100%)
Pocket: Cotton (100%)
DFJ300 Outer material: Cotton (100%)
DFJ301 Inner material: Polyester (100%)
Pocket: Cotton (100%)
DFJ400 Outer material: Polyester (100%) + titanium
DFJ401
Inner material: Polyester (100%)
Pocket: Cotton (100%)
Shoulder pad: Polyester (65%) +
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications and battery cartridge may differ from
country to country.
• Operating time may differ depending on battery type,
charging status, and usage condition.
ASSEMBLY
Installing or removing the battery
cartridge to the battery holder (Fig. 3)
CAUTION:
• Hold the battery holder and the battery cartridge
firmly when installing or removing battery
cartridge. Failure to hold the battery holder and the
battery cartridge firmly may cause them to slip off
your hands and result in damage to the battery
holder and battery cartridge and a personal injury.
To install the battery cartridge (15), align the tongue on
the battery cartridge with the groove in the battery holder
and slip it into place. Insert it all the way until it locks in
place with a little click. If you can see the red indicator (13)
on the upper side of the button, it is not locked completely.
Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out
of the battery holder, causing injury to you or someone
around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
To remove the battery cartridge, slide it from the battery
holder while sliding the button (14) on the front of the
cartridge.
Installing or removing the fan unit to the
jacket (Fig. 4, 5 & 6)
Attach the fan hook to the fan unit and pass it through the
jacket so that the fan hook can hold your belt. The fan
hook is useful for more comfortable mobility.
Attach the fan unit onto the jacket with closing the zipper.
And then fasten the snap button to secure it.
Follow the installation procedure in reverse when
removing.
Attaching the battery holder (Fig. 7 & 8)
Connect the battery holder and the power cable of the
jacket.
You can hang the battery holder on your waist belt.
6
pearly coating
Cotton (35%)
For 18V and 14.4V battery holders
The battery holder employs anti-drop function.
When removing the battery holder from the belt, pull up
the battery holder with the unlock button (16) pressed.
Attaching filter set (optional accessory)
(Fig. 9)
The filter set protects the fan unit from the dust and
powder. It is recommended to use the filter set in a dusty
or powdery work place.
Attach the sponge filter (17) to the fan unit, and then put
the filter (18) on it. Follow the installation procedure in
reverse when removing.

FUNCTIONAL DESCRIPTION

CAUTION:
• The fan jacket takes effect as intaking air which
temperature and humidity are lower than body
surface. The fan jacket may not take effect if
circumstance air temperature and/or humidity are
higher than those of in the jacket.
Switch action (Fig. 10)
To turn on the jacket, press and hold the power button
(21). The jacket starts with high air speed. Each time you
tap the power button, the air speed changes from high to
medium, medium to low, and low to high. The air speed
indicator (20) shows current air speed.
To turn off, press and hold the power button again.
Turbo button (Fig. 10)
By pressing turbo button (19), the jacket works in turbo
mode for quick cooling. The turbo mode lasts for a minute
and the air speed returns to normal.
Air flow control (Fig. 11, 12, 13 & 14)
To maintain stable air flow, close the button at the neck of
the jacket. (Fig. 11)
You can control the air flowing inside the jacket by
fastening or opening the inner zippers.
When fastening the inner zippers (Fig. 12), the most of air
flows through neck opening with high air volume. When
opening the inner zippers (Fig. 13), the air flows through
neck and sleeves openings.
For models with hood (Fig. 14)
Wear the hood with the helmet on. The air from the fan
goes through the helmet and cools your head.
Battery pocket (Fig. 15)
A pocket is provided for storing the battery holder
(with battery) inside the jacket. Connect the power cable
with the battery holder, and then put it into the pocket. The
10.8V battery holder is suitable for this pocket.
Connecting USB devices (Fig.16)
CAUTION:
• Connect only devices which are compatible with
the USB power supply port. Otherwise it may cause
malfunction to the battery holder.
The battery holder (with the battery) can work as an
external power supply for USB devices.