Specifications; Functional Description - Makita DFJ201 Instruction Manual

• Let a hot battery cartridge cool
down before charging it.
• Charge the battery cartridge if
you do not use it for a long
period (more than six months).
• For an optimum life-time, the
battery cartridge has to be fully
charged, after use.
SAVE THESE
INSTRUCTIONS.
(See the last part of this instruction manual for all the
illustrations.)
DESIGNATION OF PARTS (Fig. 1)
(1) Fan unit
(2) Power cable
(3) Battery holder

SPECIFICATIONS

Model
Material
USB power supply port
Operating time
(hour)
(Approximately)
1
Air speed 2
3
Rated voltage (V)
Battery cartridge
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications and battery cartridge may differ from
country to country.
• Operating time may differ depending on battery type
and usage condition.
ASSEMBLY
Installing or removing the battery
cartridge to the battery holder (Fig. 2)
CAUTION:
• Hold the battery holder and the battery cartridge
firmly when installing or removing battery
cartridge. Failure to hold the battery holder and the
DFJ201
Polyester (100%)
DC 5V, 2.1A (1 port)/
DC 5V, 3.0A (2 ports in total)
With battery With battery
BL1450 BL1850
20 29
15 21
8 12
14.4 18
BL1415, BL1415N, BL1430,
BL1440, BL1450, BL1815,
BL1815N, BL1820, BL1830,
BL1840, BL1850
battery cartridge firmly may cause them to slip off your
hands and result in damage to the battery holder and
battery cartridge and a personal injury.
To install the battery cartridge (4), align the tongue on the
battery cartridge with the groove in the battery holder and
slip it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator (5) on the
upper side of the button, it is not locked completely.
Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out
of the battery holder, causing injury to you or someone
around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
To remove the battery cartridge, slide it from the battery
holder while sliding the button (6) on the front of the
cartridge.
Installing or removing the fan unit to the
jacket (Fig. 3)
Attach the fan unit onto the jacket with closing the zipper.
And then fasten the snap button to secure it.
Attaching the battery holder (Fig. 4)
Connect the battery holder and the power cable of the
jacket.
You can hang the battery holder on your waist belt.

FUNCTIONAL DESCRIPTION

CAUTION:
• The fan jacket takes effect as intaking air which
temperature and humidity are lower than body surface.
The fan jacket may not take effect if circumstance air
temperature and humidity is higher than air in the
jacket temperature and humidity.
Switch action (Fig. 5)
To turn on the jacket, press and hold the power button (7).
The jacket starts with high air speed. Each time you tap
the power button, the air speed changes from high to
medium, medium to low, and low to high. The air speed
indicator (8) shows current air speed.
To turn off, press and hold the power button again.
Turbo button (Fig. 5)
By pressing turbo button (9), the jacket works in turbo
mode for quick cooling. The turbo mode lasts for a minute
and the air speed returns to normal.
Air flow control (Fig. 6, 7 & 8)
To maintain stable air flow, close the button at the neck of
the jacket.
You can control the air flowing inside the jacket by
fastening or opening the inner zippers.
When fastening the inner zippers (Fig. 7), the most of air
flows through neck opening with high air volume. When
opening the inner zippers (Fig. 8), the air flows through
neck and sleeves openings.
The sleeve of the jacket is detachable. Remove the
sleeve according to your work condition by unzipping.
5