Advertisement
Table of Contents
PaintREADY™
Contents
2
4
5
6
8
9
10
12
14
15
16
49
52
• Form No. 0529843B
0913
Station
Español
Owner's Manual
Read this manual for complete instructions
Français (page 17) / Español (página 33)
Questions?
Call Wagner Technical Service at:
1-800-328-8251
Register your product online at:
www.wagnerspraytech.com
Français
English
Advertisement
Table of Contents
Related Manuals for WAGNER 0529017
Summary of Contents for WAGNER 0529017
-
Page 1: Table Of Contents
Français (page 17) / Español (página 33) PaintREADY™ Station Contents Important Safety Information Controls and Functions Questions? Material Preparation Assembly Call Wagner Technical Service at: Air and Material Controls 1-800-328-8251 Spray Pattern Adjustment Proper Spraying Technique Register your product online at: Cleanup www.wagnerspraytech.com Reassembly... -
Page 2: Important Safety Information
No adapter should be 11. Fire extinguisher equipment shall be present used with this product. and working. Grounded Outlet Grounding Pin Cover for grounded outlet box English © Wagner Spray Tech - All Rights Reserved... - Page 3 OnLY with materials 12. Do not spray outdoors on windy days. having flashpoint above 70ºF (21ºC). 13. Hose may become hot and cause skin burn. 14. Use only Wagner HVLP hose. English © Wagner Spray Tech - All Rights Reserved...
-
Page 4: Controls And Functions
1 = Thin materials 2 = Thick materials Material Flow Control: The material flow control determines the amount of spray material that is sprayed from the spray gun. English © Wagner Spray Tech - All Rights Reserved... -
Page 5: Material Preparation
Never exceed the thinning advice given by the coating manufacturer. Do not thin with materials that have a flashpoint below 70°F (21°C). The material flashpoint should be shown on the material container. English © Wagner Spray Tech. - All Rights Reserved... -
Page 6: Assembly
Make sure the suction tube is inserted as far as it will go to ensure a tight fit. 3. Carefully screw the cup back onto the nozzle assembly. Tighten firmly. English © Wagner Spray Tech. - All Rights Reserved... - Page 7 7. Insert the air hose tightly into the connection into the turbine. The connections can be positioned as desired. IMPORTAnT: If the unit has already been used, make sure the nozzle seal is in place (see pages 13-14). English © Wagner Spray Tech - All Rights Reserved...
-
Page 8: Air And Material Controls
Spraying a thinner material at high air pressure will result in more overspray. Overspray is sprayed material that does not stick to the spray surface and bounces back. English © Wagner Spray Tech - All Rights Reserved... -
Page 9: Spray Pattern Adjustment
Use lower air power Use lower material flow Horizontal pattern Use ‘up and down’ spraying motion Vertical pattern Use ‘side to side’ spraying motion English © Wagner Spray Tech - All Rights Reserved... -
Page 10: Proper Spraying Technique
Doing this will help avoid irregularities in the finish (i. e. runs and sags). Even coat throughout Correct 6 - 8 inches Keep stroke smooth and at an even speed English © Wagner Spray Tech - All Rights Reserved... - Page 11 • Spray gun movement - moving the gun too quickly will cause the spray pattern to be too thin and excess overspray. Moving the gun too slowly will cause the spray pattern to be too coarse or thick. English © Wagner Spray Tech - All Rights Reserved...
-
Page 12: Cleanup
IMPORTAnT: If you cleaned the sprayer using mineral spirits, repeat steps 1-6 using warm, soapy water. Move on to “Cleanup - Cleaning the nozzle”, next page. PULL Empty waste container English © Wagner Spray Tech - All Rights Reserved... - Page 13 If the groove) is facing out towards this occurs, make sure to pull the front of the nozzle. Improper it out. installation will cause leakage. Groove English © Wagner Spray Tech - All Rights Reserved...
-
Page 14: Reassembly
Make sure the cup side of the seal (the side with the groove) is facing out towards the front of the nozzle. Improper installation will cause leakage. Groove English © Wagner Spray Tech - All Rights Reserved... -
Page 15: Maintenance
Turning the spray gun upside down will prevent the valve seal from falling out of the valve cover during reinstallation. 4. Place the air tube on the valve cover and on the nipple at the spray gun. English © Wagner Spray Tech. - All Rights Reserved... -
Page 16: Troubleshooting
Have you tried the recommendations above and are still having problems? In the United States, to speak to a customer service representative, call our Technical Service at 1-800-328-8251. See www.wagnerspraytech.com in the “Contact Us” section for Technical Service hours. English © Wagner Spray Tech. - All Rights Reserved... -
Page 17: Parts List
Turbina (incluye le item 2) articulo 2) 2307279 Filter Filtre Filtro 0414219 Air hose Tuyau d’air Manguera de aire 2303300 Turbine handle Poignée de pistolet Asa de pistola Français Español English English © Wagner Spray Tech. - All Rights Reserved... - Page 18 Tube / Joint de clapet Tube / Junta de la válvula 0417474 Seal Joint Sello 0417473 Suction tube Tube d’aspiration Tubo de succión 2303366 Material container Réservoir de liquide Recipiente Français English Español © Wagner Spray Tech - All Rights Reserved...
- Page 19 (une liste des centres de service après-vente accompagne cet article). Le centre de service après-vente agrée de Wagner vous renverra l’article en port payé, après l’avoir réparé ou remplacé (ce choix étant à la discrétion de Wagner).
-
Page 20: Warranty
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO one year FOLLOWING DATE OF PURCHASE. WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF THIS WARRANTY OR ANY OTHER REASON.
Need help?
Do you have a question about the 0529017 and is the answer not in the manual?
Questions and answers