Network Camera·Quick Operation Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. About This Document: This manual applies to DS-2CD8464F-E(I)(W), DS-2CD8433F-E(I)(W) series cameras. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice.
Network Camera·Quick Operation Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 4
Network Camera·Quick Operation Guide 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
Network Camera·Quick Operation Guide Contents 1 Appearance Description ..........5 1.1 Camera Description ..........5 1.2 Camera Wiring Diagram ........9 2 Installation ..............10 3 Setting the Network Camera over the LAN ....16 4 Accessing via WEB browser ......... 22...
Network Camera·Quick Operation Guide 1 Appearance Description 1.1 Camera Description Figure 1-1 Overview Table 1-1 Description Description Photosensitive resistance Infrared light PIR sensor Microphone Lens Alarm: Indicator is solid red when the camera is armed and it is solid blue when the camera is...
Page 7
Network Camera·Quick Operation Guide Description unarmed. Indicator flashes blue when movement or presence is detected in its field of view. Link: Indicator flashes orange when network connection is functioning properly. Tri-axial adjustment bracket USB interface Battery Speaker RESET: Reset button. Micro SD card slot Power supply interface 10M / 100M self-adaptive Ethernet interface &...
Network Camera·Quick Operation Guide Remote Control: Figure 1-2 Remote Control Table 1-2 Remote Control Button Description Button Description Name Status Indicating the status of the remote; when you press the Indicator button on the remote, the indicator flicks in red. Arm Button Press the button to arm the camera.
Page 9
Network Camera·Quick Operation Guide Description Button Name Disarm Press the button to disarm the camera. In the disarming Button status, the alarm linkage is disabled. Emergency Press the button to trigger the emergency alarm. The Button emergency alarm has the highest priority. Stream Switch for the video stream transmitting.
Network Camera·Quick Operation Guide 2 Installation Notes: Read the following contents carefully before the installation. Make sure that all the related equipment is power-off during the installation. Check whether the power supply is matched with your AC outlet to avoid damage.
Page 12
Network Camera·Quick Operation Guide Fixator Right cover Figure 2-1 Remove the Cover and Fixator 2. Remove the battery cover; insert the battery; reinstall the battery cover. Note: If you want to install the battery, then you can take this step.
Page 13
Network Camera·Quick Operation Guide Battery Battery cover Figure 2-2 Install the Battery 3. Stick the drilling template to the ceiling. Note: For cement ceiling mounting, you need to use the expansion screw to fix the camera. The mounting hole of the expansion pipe on the wall should align with the mounting hole of the drilling template.
Page 14
Network Camera·Quick Operation Guide Cable outlet Drilling template Figure 2-3 Stick the Drilling Template 4. Use two PA4X24 screws to fix the camera to the ceiling and the screw hole on the camera should align with the mounting hole on the drilling template. Figure 2-4 Fix the Camera...
Page 15
Network Camera·Quick Operation Guide 5. Connect the network cable and power cable; reinstall the right cover and fixator. Note: If you need to pull the cable through the side cable outlet of the camera, pull the cables from the slot without reinstall the fixator.
Network Camera·Quick Operation Guide 3 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or iVMS-4200 software to search and change the IP of network camera.
Network Camera·Quick Operation Guide Use iVMS-4200 software and to list the online devices. Please refer to the user manual of client software for detailed information. 2. Change the IP address and subnet mask to the same subnet as of your PC. Refer to the following introductions to set IP address with SADP software: ...
Page 19
Network Camera·Quick Operation Guide Figure 3-2 Searching Online Devices Note: Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online...
Network Camera·Quick Operation Guide Note: You can click on each column heading to order the information; you can click to show the device table and hide the network parameter panel on the right side, or click to show the network parameter panel.
Page 21
Network Camera·Quick Operation Guide Figure 3-3 Select a device Figure 3-4 Modify Network Parameters 3. Enter the IP address of network camera in the address field of the web browser to view the live video.
Page 22
Network Camera·Quick Operation Guide Notes: The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”. For accessing the network camera from different subnets, please set the gateway for the network camera after you log...
Network Camera·Quick Operation Guide 4 Accessing via WEB browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above...
Page 24
Network Camera·Quick Operation Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
Page 27
Network Camera·Quick Operation Guide Figure 4-5 Install Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, please refer to the user manual of network camera.