Table of Contents
Advertisement
, Push in the Center;
Pull Down
A Twist of the Wrists
Raise Signal
Arm to Stop Ice Maker.
Lower
Signal
Arm to Start It.
Push the Tab
to Clear the Cover
Snap Back Into Place
Removing the light Shield.
You may want to remove
the light shield
when
cleaning,
or for
changing
the bulb. First, unplug
the refrigerator.
Then, push lightly
on
the upper
center
of the shield
until the notched
tab is free from the
console.
Pull down
until the tab clears, then lift the back
hooks out of
their slots.
To replace
it, do the reverse.
Ice Cube Trays.
To remove
ice from the flexible
ice trays, hold a tray at both ends,
as shown. Slightly
twist the tray; the ice will come
out easily.
If cubes
are not used for a number
of weeks,
they may
become
smaller.
The moving
air is so cold
that it starts a slow evaporation.
(That's also why its so important
to wrap
food carefully.)
The longer
they are stored, the smaller
they can get.
Optional
ICE MAGIC@ Automatic
Ice Maker.
If you have the automatic
ice maker accessory
(Part No. ECKMF-61,
or plan to add one, there are a few things you will want to know:
l
On the side of your ice maker
is a wire signal
arm. When it's down,
the ice maker
will make
ice automatically.
Raise the arm to shut
off the ice maker.
l
Shake
the bin occasionally
to keep
cubes
separated,
and
to
obtain
increased
storage
capacity.
It is normal
for the cubes
to be
attached
by a corner. They will break
apart
easily.
l
You will hear water
running
when the ice maker
is working.
You'll
hear ice fall into the bin. Don't let these new sounds bother
you.
l
The ice maker
will not operate
until the freezer
is cold
enough
to
make
ice. This can take overnight.
l
Because
of new plumbing
connections,
the first ice may
be dis-
colored
or off-flavored.
l
Your ice maker
will work faster when the freezer
is colder.
If you
want more ice, turn the Temperature
Control
dial to a higher
num-
ber, or turn the Air Control
dial toward
a higher
number.
l
If you remove
the ice bin, make
sure you raise the signal
arm to
shut off operation.
When you put the bin back, make
sure its all the
way in and the arm is lowered.
l
If cubes
are stored too long, they may develop
an off-flavor...like
stale water. Throw them away.
They will be replaced.
Cubes
in the
ice bin can also become
smaller
by evaporation.
Moving the Meat Pan and Cover.
The meat pan can be fitted under any of the shelves...in
the mid-
dle or either
side. To move
it, remove
the meat
pan by pulling
for-
ward, lifting over the stops and pulling
it out the rest of the way.
Remove
the cover
by lifting
up the front and pulling
the unit for-
ward and out. To replace
it, fit the notches
in the sides of the cover
over the center
shelf support.
Lower the cover
into place
and slide
the meat pan into the side supports.
Removing the Crispers and Crisper Covers.
To remove
the crispers,
slide them out until they stop. Lift the front a
little and slide them the rest of the way out.
Each cover
is held
in place
by two pegs
at the back
and two
notched
tabs in the front. Press the tabs out of the way to lift the front.
Lift the back
off the pegs.
To put the covers
back,
replace
the center
leg. Replace
each
cover
by first fitting the back
notches
over the pegs. Then push the
front down
into the notched
tabs.
The center
leg can be made
shorter
or longer
to help
level
the
crisper
covers,
if necessary.
Hold the leg
and
turn the top
part
counter-clockwlse
to make the leg longer. Turn it clockwise
to shorten
the leg.
5
Advertisement
Table of Contents
